Bedienungsanleitung Christopeit WALKER (Seite 17 von 44) (Deutsch, Englisch, Holländisch, Französisch)

602838

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

English

Step 8:

Checks

1. Check the correct installation and function of all screwed and plug con-

nections.

2. When everything is in order, familiarise yourself with the machine at a

low resistance setting.

Note:

Please keep the tool set and the instructions in a safe place as these may

be required for repairs or spare parts orders becoming necessary later.

How to move/store your treadmill:

1. Pull the locking Knop (54) and place your hand on the end cap of the

system frame then folding the system frame up and lock it with locking

knob.

2. Place your hands on top of the handrails, than lean the machine toward

your body sideways, this way you can move it easily.

3. Pull out the locking knob (54) and fold down slowly the main frame (1) to

the ﬂ oor and ensure that the locking knob (54) secures this position.

Possible faults and their remedies

Most faults which can occur can be rectiﬁ ed by the following, simple

steps.

1. The computer no longer operates correctly

a) Check that all plugged connections are made correctly.

b) Check whether the batteries still have sufﬁ cient capacity/power.

2. The belt (36) no longer runs evenly

To achieve even running and to reduce the friction between the belt (36)

and the board (35), you should apply a silicone-based lubricant occasio-

nally on the slip surface beneath the belt (36). Ensure that the lubricant is

not based on an oil or petroleum compound.

3. The belt (36) no longer runs centrally or slides

a) If the belt (36) has run to the left of the direction of running, turn the left

screw (5) clockwise and the right screw (5) anticlockwise by a quarter of a

revolution each. Run brieﬂ y on the belt.

If the belt still does not run centrally, repeat the above procedure.

b) If the belt (36) has run to the right of the direction of running, turn the left

screw (5) anticlockwise and the right screw (5) clockwise by a quarter of a

revolution each. Run brieﬂ y on the belt. If the belt still does not run central-

ly, repeat the above procedure.

c) If the belt (36) slips, turn both screws (5) clockwise by a quarter of a re-

volution. Run brieﬂ y on the belt. If the belt (36) still slips, repeat the above

procedure.

Step 7:

Installation of Walking sticks (69) at supports (24+33) with the screws

(78), washers (77) and selﬂ ocking nut (76).

1. Place the screws (78), washers (77) and nuts (76) beside the foot (23).

2. Put the walking stick (69) with walking stick holder (71) into appropriate

holder at the supports (24+33) so that the holes align.

3. Push the screws (78) through the holes and put on each screw end one

washer (77) and a nut (76). Screw it tightly, so that the walking sticks can

move in an easy way.

4. Finally, cover the selﬂ ocking nuts (76) with a screw cap (75).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit WALKER Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info