Bedienungsanleitung Christopeit XL 2 (Seite 18 von 44) (Deutsch, Englisch, Holländisch, Französisch)

585792

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Computer Instructions

The supplied training computer allows the most convenient training. Every

value relevant to training is displayed in the two-part window.

The speed, the distance covered during the current training session, the

time required, the distance covered for all completed training units and

including the current session, the approximate calorie consumption and

the pulse rate are shown from the start of the training session. All values

count upwards from zero.

Switch the computer on by brieﬂy pressing the ‘F’ button or moving a

pedal slightly.

The speed is indicated on the upper display. All other values are indicated

on the lower display.

If you wish to see one value displayed constantly as well as the speed during

training, select this with the „F“ key. If you wish to see these values in

constant alternation, select the „SCAN“ function. The display then changes

from one function to the next at intervals of approx. 6 seconds.

Simply begin your training to start the computer. The computer begins to

record and display all the values reached.

Simply end your training to stop the computer. The computer stops all

measurements and retains the last values that were measured. The most

recently reached values in functions KM, TIME, KM-TOTAL and CALORIES

are saved and are displayed again when training restarts. You can continue

training on the basis of these values.

If you wish to delete the most recently reached values, stop your training

session and hold down the ‘F’ button for around 5 seconds. The values for

all displays that can be modiﬁed are reset to zero (Exeption: KM-TOTAL).

The computers switches itself off automatically approx. 5 minutes after

the end of training and deletes the most recent values. All the displays are

reset to zero when the computer is restarted and count upwards (Exeption:

KM-TOTAL).

1. „SCAN“ display:

Selecting this function causes the achieved values of the functions KM,

TIME and CALORIES to be displayed alternately at intervals of approx. 6

seconds.

2. ”SPEED” display:

The current speed in kilometres per hour is displayed. The values most

recently reached can not be saved in this function, as described above.

(Max. display limit is 99.99 kmh)

3. ”DIST” display:

This shows the number of kilometres covered. The values most recently

reached can be saved in this function, as described above.

(Max. display limit is 99.99 km)

4. ”TIME” display:

This displays the time currently required in minutes and seconds. The values

most recently reached can be saved in this function, as described above.

(Max. display limit is 99.59 minutes)

5. ”CALORIES” display:

The approximate number of calories consumed up to that moment is dis-

played. The values most recently reached can be saved in this function, as

described above.(Max. display limit is 999.9 calories)

6. „TOTAL DIST“ (ODO) display:

The current status of the travelled kilometres of all previous training sessions

including current training session is displayed. A particular value cannot be

speci. ed. The values last attained by this function are not stored. (Limit of

the display: 9.999 km.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit XL 2 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info