Bedienungsanleitung Ciclo CM 628 Master (Seite 3 von 16) (Englisch)

588917

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

38 39

2.1 Installing the handlebar bracket

The handlebar bracket can be attached to the handlebars

or to the stem. To use on the stem, slide off the upper part

of the handlebar bracket from the lower section by

pressing the snap-closure

mechanism (e.g. with a pin).

Now rotate upper part through

90° and reconnect to the lower

part, until the snap-closure

mechanism engages audibly

and visibly.

Remove the protective foil on

the underside of the handlebar

bracket and place the handlebar

bracket at the required location

on the handlebars (or on the

stem) and press slightly. Fasten

with the cable tie.

Slide the CM 628 onto the

bracket in the direction of the

arrow until it engages audibly and

visibly (release button must be at

the initial position). In order to

remove it again, press down the release button behind the

CM 628 and remove the CM 628 with light pressure.

2.2 Installing the speed transmitter

Attach speed transmitter to the

fork or to the rear construction

with the aid of the attached O-

ring (marked side of the trans-

mitter must point to the spokes).

Suspend the O-ring on one side

of the transmitter, wrap it around

the fork and likewise suspend on

the opposite side.

Mount the magnets on a spoke directly opposite the

transmitter, so that the magnet points exactly to the marker

on the transmitter. Do not over tighten the fixing screw on

1. GENERAL INFORMATION

Warning: whoever carries out sport should have a general

medical check up on his/her general state of health -

especially beginners, persons older than 35 years of age

and anyone who has suffered from illnesses or injuries in

the past. It is recommended that a doctor be consulted in

any case in the presence of risk factors, such as smoking,

high blood pressure, high cholesterol values, diabetes, lack

of exercise and excess weight.

Pacemaker wearers should consult their doctor

before using any heart rate measurement device!

Measurement of the heart rate is only possible if the trans-

mitter belt is fitted correctly (see Chap. 2.4) and the

CM 628 is within the transmitter’s reception range

(approx. 10 m).

The CM 628 has been set to receive the signals from the

chest belt. It is supplied ready to use, but may require user

initialisation under certain circumstances (see Chap. 4.6 –

Initializing the receiver for heart rate monitoring).

The heart rate can be measured even when the CM 628 is

not mounted on the bike. In this case start the heart rate

transmitter search by short pressing both buttons when in

heart rate mode ('H' in lower display).

If a ➀ appears in the top left of display, the indicated

values apply to Bike 1. In order to display the values for

Bike 2, press both buttons simultaneously for a brief period

(the changeover is only possible if the speed = 0) and a ➁

will appear in the top left of display. To switch back to

values for Bike 1 press both buttons simultaneous again

briefly, and the display will show ➀.

2. OPERATIONAL STARTUP

The CM 628 is set in the power-saving mode. By pressing

any button, it switches to the normal operating mode.

If no characters or unintelligible characters appear in the

display, press the AC button on the reverse side of the

CM 628 (repeat if necessary) with the aid of a ballpoint

pen (or similar).

Caution: Longer pressing of the AC button (3 sec.) causes

a total reset, i.e. the initialisation already carried out at the

works is also deleted with that, and so the speed, as well

as the cadence- and heart rate transmitter, must be initia-

lised again (see Chap. 4.3, 4.5 and 4.6).

02 CM 628 englisch 34-65 19.05.2005 10:23 Uhr Seite 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo CM 628 Master Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM 628 Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info