Bedienungsanleitung Ciclo CM 8.3 A Master (Seite 10 von 11) (Englisch)

588920

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

their training. But how do you train to achieve those aims in the most

efficient possible manner? How do you find the right intensity of effort

during the training? CICLOInZone

is the optimum training ZONE for

effort, resistance and weight loss.

What does CICLOInZone

do?

It calculates the optimum training zone for effort, resistance and

weight loss. The values vary from person to person and they offer a

valid training support – always staying between 70 % and 85 % of the

maximum heart rate.

(+/- 5% of tolerance, taking into consideration the actual heart rate

when at rest and the level of training).

The question of burning fat is seen in the “correct” light with

CICLOInZone

– on the basis of the personal data collected.

9. Battery change

CM 8.3A: First you should put CM 8.3A into the “Powerdown Mode”

(see chapter 5 Settings) Open battery cap with a coin (unscrew to the

left). Insert battery type CR2032 (please use battery with smooth minus-

pole) with plus-pole facing up. Close battery cap, being sure not to over

tighten. After inserting the battery the display will show normal mode.

(Speed-)Transmitter: Open battery cap at the top of the transmitter

with a coin (unscrew to the left), remove old battery and insert new 12

V battery, type 23A (with pluspole facing up). Close battery cap, being

sure not to over tighten.

(Battery change in the optional cadence transmitter works in the same

way.)

Please do not throw away battery in your normal garbage.

10. Trouble shooting

Faulty or no display

- check to see if battery is installed properly or replace battery (Attention:

removing battery will clear all settings and values in the CM 8.3A)

- press AC-button on the rear of the computer

Actual Speed not displayed

- transmitter hasn`t been initialized (see chapter 5)

- check to see if wheel-sensor is mounted properly

- check the position of the spoke magnet (max. 3 mm distance to wheel-

sensor)

- make sure CM 8.3A is mounted in bracket correctly

- check wheel circumference

- start transmitter search (press left button for 3 seconds)

Speed to high or to low

- check wheel circumference

- check to see if you are using miles or kilometers

Transmitters cannot be initialized

(initialization is very slow or “error” displayed)

- Tranmitter battery is discharged or transmitter is defect

- Transmitter has already been initialized for one of the bikes. If you still

want to initialize the transmitter for the current bike you must initialize

the transmitter again for the other bike, but without an active transmit-

ter. “Error” will be displayed. Now you can initialize it again with the

choosen bike.

Automatic search of the transmitter doesn’t start by moving

the bike.

- CM 8.3A is not correctly located in the handlebar bracked

- A transmitter has already been found (CM 8.3A displays SPD 0) e.g. if

you switch bikes. If you stay in the transmitting area of the first trans-

mitter CM 8.3A displays 0. If CM 8.3A is outside the transmitting area

it will display “-“. With the next movement of the bike the transmitter

search will start again.

- transmitter hasn`t been initialized (see chapter 5)

No heart rate displayed or values displayed are incorrect or

unstable

- proof whether heart rate is switched on in setting mode

- Check transmitter belt (battery)

- Skin too dry or cold

- Distance between CM 8.3A and transmitter belt is too big (max. 5m)

- start manual transmitter search (press left button for 3 seconds)

Manual transmitter search doesn’t start

- no transmitter has been initialized

Cadence is not displayed or value incorrect or unstable

- Check whether switched on in setting mode

- Check sensor and magnet for correct installation

- start transmitter search (press left button for 3 seconds)

CM 8.3A is making noise

- its normal because of the automatic movement sensor

PC Recording doesn’t start

- storage is full, you have to delete recorded tours (with HACtronic

program or the reset function in settings of CM 8.3A see chapter 5;

Attention: the other values will be deleted also)

Wrong values displayed for the altitude

- Check home-altitude values (adjusting mode), you may have adjusted

wrong values

- Air pressure has changed, e.g. caused by changing weather conditions

(readjust current hight)

11. Guarantee

We offer a guarantee for 2 years from the date of purchase on the CM

8.3A. The guarantee is limited to material and processing faults. Broken

transmitters, or damages of wasted parts of CM 8.3A are excluded from

the guarantee.

The guarantee is valid only if the computer, with accessories, has been

handled and maintained carefully and according to operating instructions.

The guarantee will take place through changes of or repairing the defective

parts. The guarantee doens’t cover direct, indirect or subsequent damages

which are related to the product.

This guarantee doesn’t limit any rights of the consumer (considering rela-

tive national law) in respect to the dealer.

To return the CM 8.3A under conditions/terms of the guarantee, please

refer to your dealer, your local distributor or send the computer with the

proof of purchase (date) and all accessories and with sufficient postage

to:

CICLO SPORT SERVICE

K. W. Hochschorner GmbH

Konrad-Zuse-Bogen 8

D-82152 Krailling

E-Mail: ciclo-service@ciclosport.de

Please read through the operating manual again carefully before sen-

ding in the device and check the battery.

In case of valid guarantee claims, the repaired device or a replacement

device will be returned free of charge.

Repair:

If your CM 8.3A is sent in for repair (or battery change) or if a gua-

rantee claim is not valid, repairs up to EUR 19.- will be carried out

automatically.

In case of higher repair costs you will be notified. The repaired device

will be sent back COD.

Ciclo CM 8.3 A Master Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM 8.3 A Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info