Bedienungsanleitung Ciclo CM9.3A Master (Seite 7 von 18) (Englisch)

588934

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Chapter 3 – settInGs & fIrst start

In this chapter you will learn how to install and set up the CM 9.3 A (+) before the ﬁrst ride. Please note that

functions with this Symbol are only available with the (+) Version or with the optional accessories.

3.1 Mounting

3.1.1 Handlebar bracket

You can mount the handlebar bracket on the handlebar or on the stem. For mounting it on the stem, unscrew

the four screws as shown in picture 1, turn the lower part of the handlebar 90° degrees and secure it again

with the screws.

Peel off the adhesive protection and attach the rubber pad to the bottom side of the handlebar bracket.

Run the cable ties through the eyelets and position the handlebar bracket on the handlebar or on the stem.

Fix the mount with the cable ties. The ends of the cable ties can be cut off with a clipper or scissors.

3.1.2 Speed sensor

Attach the transmitter to the fork or the left chain stay. Pull the cable ties through the eyelets of the trans-

mitter, place it in the desired location and tighten the cable ties. The ends of the cable ties can be cut off with

a clipper or scissors.

3.1.3 Cadence kit

Mount the sensor as shown in picture 2 (do not tighten the cable ties, yet). Attach the cadence magnet as

described below and check the maximum distance of 3mm. Only after the cadence is initialized (Section

3.7.1), tighten the cable ties. The ends of the cable ties can be cut off with a clipper or scissors.

3.1.4 Spoke magnet

Attach the magnet to a spoke on the opposing of the transmitter.

Please note that the distance between the sensor and the magnet shall not be more than 3mm.

Please make sure to align the magnet on the markings on the sensor.

3.1.5 Trittfrequenz-Magnet

Attach the cadence magnet with a cable tie to the left crank arm, as described in picture 2. Please note that

the distance between the sensor and the magnet must not be more than 3mm.

Please make sure that the magnet is aligned with the marking on the sensor.

3.1.6 Heart rate belt

Attention: Every person who carries out sport should have a general medical checkup on his/her general

state of health Especially beginners, persons older than 35 years of age and anyone who has suffered from

illnesses or injuries in the past. It is recommended that a doctor is consulted in case of risk factors, such as

smoking, high blood pressure, high cholesterol values, diabetes, lack of exercise and excess weight.

Pacemaker wearers should consult their doctor before using any heart rate measurement

device!

Moisten the contacts on the harness and attach the transmitter belt. The chest strap should be worn centered

just below the nipples.

The heart rate can only be displayed if:

- The chest belt ﬁts correctly

- The heart rate function is activated (Chapter. 3.7)

- The heart rate belt has been initialized with the CM 9.3 A (+)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo CM9.3A Master Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM9.3A Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info