Bedienungsanleitung Ciclo HAC 4 Pro (Seite 3 von 15) (Englisch)

588929

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

1. GENERAL INFORMATION

The HAC is a multi-functional device which unifies a heart

rate monitor, an altimeter, and a wireless cycling computer in one.

That is why it is the ideal device for monitoring training.

It has a 2-part display so that the functions shown on the upper

display can be combined with those shown on the lower display.

Furthermore, the HAC offers 3 pulse settings on the dis-

play so that the pulse can be shown with every other function.

The HAC also has a storage function which offers the pos-

sibility to compare tours (evaluation is possible with any PC equipped

with at least Windows 98, 2000, NT and XP with the accessory unit

HACtronic).

Persons who wear a cardiac pacemaker should contact their

physician before using this device to measure their pulse!

2. OPERATION

Basically, the following applies:

- Heart rate measurement is only possible when the breast belt is

properly put on and the HAC is not farther away from the

breast belt transmitter than 60 cm.

- In order to be used as a cycling computer, the transmitter must

be properly attached and the HAC must be properly

attached to the handlebar bracket which holds the receiver for the

wireless transmitter.

2.1 Inserting the batteries

When you purchase your HAC the depending parts need

to be supplied with batteries.

Note: please do not remove the foil inside the battery case of the

HAC4000. Insert battery below the foil.

First insert the batteries type CR2032 in the HAC , the hand-

lebar bracket and in the transmitter belt. Unscrew counter clockwise

the screwed cap on the reverse side of the HAC /transmitter

belt (and at top of handlebar bracket) with the aid of a coin. Insert the

battery with plus pole facing up and close screw caps again.

Open the battery cap of the speed transmitter also with the aid of a

coin. Insert battery type 23A with plus pole facing up (to battery cap)

and close cap again. Do not over twist battery caps!

2.2 Putting on the breast belt

Hang the transmitter belt in the elastic

breast belt and then put the breast belt

around your (naked) upper torso. The

transmitter (plastic part with inscription)

should be placed above the middle

of your upper stomach region, slightly

below the breast and the inscription on

the transmitter (when seen from the front) must be legible (pictured).

Pull the belt tight so that it always is in contact with your body when

moving and so that it can not slip. If the breast belt is not long

enough, a longer breast belt can be acquired from your local bicycle

dealer.

If your skin is too cold or too dry, the electrical contact between

the skin and the electrodes can be so minimal that an accurate

measurement is not possible. It often helps to wet the electrodes and

the skin where they are to be attached with your finger (do not wet

the transmitter but only the rubber parts on the left and on the right).

If this doesn’t help, one should train until they start sweating. You will

get the best contact by means of a special electrode-gel (available at

your local pharmacy).

2.3 Attaching the handlebar bracket and speed

transmitter

The handlebar mounting can be installed on a stem. To do this the

top section of the handlebar mounting must be removed from the

bottom section. For this open the 4 screws of the bottom section.

Then turn upper part through 90° and assemble it again with the

4 screws of the bottom section.

Remove the backing foil from the underside of the handlebar moun-

ting, place the handlebar mounting in the required position on the

handlebar (or on the stem) and press it down slightly. Secure it with

the O ring or with the cable ties

Attach the transmitter by using

the rubber shim and the cable-ties

to the front side of the right fork

or the back side of the left fork

(the flat side of the transmitter

must face towards the inside) no

further than 60 cm away from

the computer. Do not yet pull the

cable-ties tight. Make sure that

the transmitter’s battery cap is facing up and that the transmitter and

computer are both attached to the same side of the bicycle.

Attach the magnet to the spokes directly opposite to the transmitter,

so that the magnet points directly to the elongated marking on the

flat side of the transmitter. Be careful not to over wind the screw for

attaching the magnet.

Turn the transmitter so that the distance between the trans-

mitter and the magnet is not more than 2 mm.

2.4 Attaching the cadence (optional)

Plug in the cadence cable on the respective place of the handlebar

bracket. Wind the cable in a helical way round the frame in direction

to the pedal (on the left side of the bike).

Mount the sensor (on the end of the cable) on a suitable place

opposite the crank (as near as possible) and fasten it with the cable

ties. Mount the cadence magnet opposite the marking of the sensor

(distance between cadence magnet and sensor max. 5 mm).

If the cadence should be used, this function must be set ‚on‘ in the

setting mode 1 of the HAC (see chap. 4.1, function ‚Cc‘).

Electrodes

Transmitter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo HAC 4 Pro Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo HAC 4 Pro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info