Bedienungsanleitung Cisco 820 Series (Seite 8 von 10) (Englisch)

605003

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Cisco 820 Series and SOHO Series Routers Cabling and Setup Quick Start Guide

78-13937-04

6: Check the PC Configuration

Each PC that is connected to the router must be configured to use the Transmission Control

Protocol/Internet Protocol (TCP/IP) and to obtain its IP address automatically. Follow these steps to

configure each PC that is running Microsoft Windows NT or Microsoft Windows 95 or 98. If the PC is

running a different version of Microsoft Windows, refer to the documentation that came with the PC.

Step 1 Start the PC, and open the Control Panel.

Step 2 Click the Network icon to display the Network window.

Step 3 Verify that TCP/IP has been added and associated with the Ethernet adapter. TCP/IP is shown as a cable

icon in the Configuration window on Microsoft Windows 95 and 98; and as a cable icon in the Protocol

window on Microsoft Windows NT. If the icon is not visible, click Add, and add Microsoft TCP/IP.

Step 4 To verify that the PC is configured to obtain an IP address automatically, click the TCP/IP cable icon,

and select the IP address tab in the TCP/IP Properties window. If it is unchecked, check Obtain an IP

address from a DHCP server. The IP address and Subnet mask fields should be grayed out.

Step 5 To accept all changes and exit this window, click OK. Then click OK in the Network window.

Step 6 If you are prompted, click Ye s to reboot the PC.

For more information on how to configure TCP/IP, refer to the Cisco Router Web Setup Troubleshooting

Guide, which is available on Cisco.com.

7: Configure the Router with Cisco Router Web Setup

The Cisco Router Web Setup (CRWS) software is loaded on the router and should be used to configure

it to connect to the Internet. The CRWS software runs on Netscape version 3.0 to 4.7, and on Internet

Explorer version 4.0 or later. Follow these steps to start the CRWS software and configure the router:

Step 1 Start, or restart, a PC connected to one of the router Ethernet ports (1, 2, 3, or 4).

Step 2 Open a web browser. Make sure that the browser is set to work in online mode.

• In Internet Explorer, click the File menu, and verify that the “work offline” option is unchecked.

• In Netscape, the default selection in the File menu is set to work online.

Step 3 Type in the following universal resource locator (URL):

http://10.10.10.1

The home page of the router should appear after one or two minutes.

Tip If the CRWS home page does not appear when you enter the URL http://10.10.10.1, test the connection

between the PC and the router by doing the following:

1. Check that the OK LED on the router is on, and check the cable connection between the router and

the PC. Be sure that the TO HUB/TO PC button is in the correct position. The position is correct if

the LED for the port on the front of the router is on.

2. If the CRWS home page still does not appear, verify that the web browser’s “work offline” option

is disabled.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cisco 820 Series Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info