727972
305
Zoom out
Zoom in
Vorherige Seite
1/316
Nächste Seite
Cisco Systems, Inc.
www.cisco.com
Cisco has more than 200 offices worldwide.
Addresses, phone numbers, and fax numbers
are listed on the Cisco website at
www.cisco.com/go/offices.
Cisco 800 Series Integrated Services
Router Hardware Installation Guide
July 31, 2016
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be
determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1721R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display
output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in
illustrative content is unintentional and coincidental.
Cisco 800 Series Integrated Services Router Hardware Installation Guide
© 2016 Cisco Systems, Inc. All rights reserved.
1
Cisco Integrated Services Router Hardware Installation Guide
CONTENTS
Preface vii
Objective vii
Audience vii
Organization viii
Conventions viii
Related Documentation xvi
Searching Cisco Documents xvi
Obtaining Documentation and Submitting a Service Request xvi
Product Overview 1-1
Cisco 810 Series 1-1
Cisco 812 Series 1-1
General Description 1-1
Hardware Features 1-4
SKU Information 1-9
Cisco 819 Series 1-10
General Description 1-10
SKU Information 1-14
Hardware Features 1-23
Cisco 860, 880, 890 Series 1-38
General Description 1-39
Cisco 860 Series ISRs 1-39
Cisco 860VAE Series ISRs 1-41
Interfaces 1-41
IOS Images 1-41
Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and
Cisco 860VAE-POE-W-A-K9 ISRs
1-43
Model-Specific Features 1-43
Common Features 1-44
Cisco 880 Series ISRs 1-47
Cisco 880 Series Data Routers 1-48
Cisco 880 Series Voice and Data Routers 1-51
Cisco 880 Series with Embedded WLAN Antennas 1-57
C881G-B/S/V-K9 ISRs 1-59
C881GW-S/V-A-K9 ISRs 1-59
Contents
2
Cisco Integrated Services Router Hardware Installation Guide
C881G-U-K9 ISRs 1-60
HSPA+ Versions of the Fixed-Platform ISRs 1-60
Cisco C881, C886, and C887 Series ISRs 1-60
Cisco C881 Router 1-61
Cisco C886VA Router 1-62
Cisco C886VAJ Router 1-63
Cisco C887VA Router 1-64
Cisco C887VAM Router 1-65
Cisco C888 Integrated Services Router 1-67
Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers 1-70
Cisco C881G-4G Integrated Services Router 1-79
Cisco C886VAG-LTE 1-82
Cisco C887VAG-4G Integrated Services Router 1-85
Cisco C896VAG-LTE Integrated Services Router 1-88
Cisco C897VAG-LTE Integrated Service Router 1-92
Cisco C898EAG-LTE Integrated Service Router 1-95
Cisco C899G-LTE Integrated Service Router 1-99
Cisco 890 Series Integrated Service Routers 1-104
Cisco 891, Cisco 892, and Cisco 892F 1-104
Cisco C897VAB-K9 1-114
Cisco C891 Series ISRs 1-117
Cisco C891F Router 1-117
Cisco C891FW Router 1-119
Cisco C891-24X/K9 Integrated Services Router 1-121
Hardware Features 1-122
Kensington Lock 1-123
Reset Button 1-123
LEDs 1-125
Memory 1-131
USB Port 1-132
Fan 1-133
Power Supply 1-133
Power over Ethernet Module 1-133
3G Cellular Data WAN Connectivity 1-134
Small Form-Factor Pluggable Port 1-136
Feature Summary 1-136
Installing the Router 2-1
Installing the Cisco 810 ISR 2-1
Installing the Cisco 812 ISR 2-1
Contents
3
Cisco Integrated Services Router Hardware Installation Guide
Items Shipped with your Router 2-2
Items Shipped with your PoE+ Splitter 2-2
Installing the Cisco PoE+ Splitter 2-2
Grounding the Cisco 812 ISR 2-18
Installing the Cisco 819 ISR 2-19
Installing the Router 2-22
Mounting the DC Power Supply 2-39
Installing the Cisco 860, 880, 890 ISR 2-40
Equipment, Tools, and Connections 2-41
Items Shipped with your Router 2-41
Additional Items 2-41
Connections 2-42
Ethernet Devices 2-42
Installing the Cisco 860, 880, and 890 Series Routers 2-42
Warnings 2-42
Installing on a Table 2-43
Mounting on a Wall 2-43
Installing the Router Ground Connection 2-46
Installing the FIPS Cover 2-46
Installing Antennas for Cisco 890 Series 2-50
Installing Cisco 890 Series in a Rack 2-54
Installing the C881G-B/S/V-K9 ISR 2-56
Installing Antennas 2-56
Installing the C881GW-S/V-A-K9 ISR 2-56
Installing Antennas 2-56
Installing the C881G-U-K9 ISR 2-56
Installing the Cisco 880G for 3.7G (HSPA+)/3.5G (HSPA) ISRs 2-58
Connecting the Router 3-1
Cisco 810 Series 3-1
Cisco 819 Series 3-1
Preparing to Connect the Router 3-1
Connecting a PC, Server, or Workstation 3-2
Connecting an External Ethernet Switch 3-3
Connecting a Terminal or PC to the Console Port 3-4
Connecting a Modem to the Console Port 3-5
Connecting the AC Adapter 3-5
Connecting the DC Adapter 3-6
Verifying Connections 3-7
Cisco 860, 880, 890 Series 3-8
Contents
4
Cisco Integrated Services Router Hardware Installation Guide
Safety Warnings 3-9
Preparing to Connect the Router 3-10
Preventing Damage to the Router 3-11
Connecting a PC, Server, or Workstation 3-12
Connecting a Phone 3-13
Connecting an External Ethernet Switch 3-14
Connecting the V.92 modem Port 3-15
Connecting a Terminal or PC to the Console Port 3-16
Terminal Emulator Settings 3-16
Connecting a Modem to the Auxiliary Port 3-17
Connecting the 3G Card 3-18
Installing the 3G Adapter for Extended Cable/Antenna 3-24
Connecting a Data BRI Port 3-28
Connecting an FE Line to an FE WAN Port 3-30
Connecting a GE Line to an GE WAN Port 3-31
Connecting an xDSL Line 3-31
Connecting Power over Ethernet 3-34
Connecting the AC Adapter 3-35
Connecting an FXS Line 3-39
Connecting an FXO Line 3-40
Connecting a Voice ISDN BRI Line 3-42
Verifying Connections 3-45
Initial Configuration 4-1
Cisco 810 Series 4-1
Cisco 819 Series 4-1
Cisco IOS CLI 4-1
Setup Command Facility 4-1
Verifying the Initial Configuration 4-2
Cisco 860, 880, 890 Series 4-2
Cisco Configuration Professional Express 4-2
Cisco IOS CLI 4-2
Setup Command Facility 4-4
Verifying the Initial Configuration 4-6
Initial Configuration of the Wireless Access Point 4-7
Technical Specifications A-1
Cisco 810 Series A-1
Cisco 812 Series A-1
Router Specifications A-1
Contents
5
Cisco Integrated Services Router Hardware Installation Guide
Mean Time Between Failure Ground Benign Environment A-4
Cisco 819 Series A-4
Router Specifications A-4
Mean Time Between Failure Ground Benign Environment A-8
Supported Power Adapters A-9
Cisco 860, 880, 890 Series A-11
Router Specifications A-12
All Models Except Cisco 860VAE Series A-12
Cisco 860VAE Series A-14
Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 Series A-15
Cisco 870 Series A-16
Cisco 880 Series A-17
Cisco 880G Series 3G Wireless Integrated Services Router A-19
Cisco 880VA Series A-19
Cisco 890 Series A-21
Power Supply A-22
Wireless Access Point A-22
FE and GE Port Pinouts A-23
Console and Auxiliary Port Connector Pinouts A-24
FXS and FXO Port Connector Pinouts A-24
VDSL2 Port Connector Pinouts A-24
ADSL2+ Port Connector Pinouts A-25
V.92 Port Connector Pinouts A-25
G.SHDSL Port Connector Pinouts A-25
Data BRI Port Connector Pinouts A-26
Voice ISDN BRI Interface Pin Numbers and Functions A-27
SFP Port Connector Pinouts A-27
Cable Specifications A-28
Ethernet Cable Specifications A-28
Maximum Cable Length A-28
Contents
6
Cisco Integrated Services Router Hardware Installation Guide
vii
Cisco Integrated Services Router Hardware Installation Guide
Preface
This preface describes the objectives, audience, organization, and conventions of this guide and
describes related documents that have additional information. It contains the following sections:
Objective, page vii
Audience, page vii
Organization, page viii
Conventions, page viii
Related Documentation, page xvi
Searching Cisco Documents, page xvi
Obtaining Documentation and Submitting a Service Request, page xvii
Objective
This guide provides an overview and explains how to install, connect, and perform initial configuration
for the following series:
Cisco 810 series ISRs that include both Cisco 812 series and 819 series ISRs
Wireless and non-wireless Cisco 860 series, Cisco 880 series, and Cisco 890 Integrated Services
Routers (ISRs)
Audience
This guide is intended for Cisco equipment providers who are technically knowledgeable and familiar
with Cisco routers and Cisco IOS software and features.
viii
Cisco Integrated Services Router Hardware Installation Guide
Organization
This guide is organized into the following chapters and appendix.
Conventions
This section describes the conventions used in this guide.
Note Means reader take note. Notes contain helpful suggestions or references to additional information and
material.
Caution This symbol means reader be careful. In this situation, you might do something that could result in
equipment damage or loss of data.
Tip Means the following information will help you solve a problem. The tip information might not be
troubleshooting or even an action, but could be useful information.
Chapter Name Description
Chapter 1 Chapter 1, “Product Overview” Describes the router models and the
hardware features available.
Chapter 2 Chapter 2, “Installing the Router” Lists the items shipped with the router, the
equipment and tools necessary for
installing the router, the safety warnings
and guidelines, and the procedures for
installing the router.
Chapter 3 Chapter 3, “Connecting the Router” Describes typical connections for the
router, procedures for connecting the
router to various devices, and how to
verify the connections.
Chapter 4 Chapter 4, “Initial Configuration” Provides the procedures for initially
configuring the router settings.
Appendix A Appendix A, “Technical Specifications” Provides the router, port, and cabling
specifications.
ix
Cisco Integrated Services Router Hardware Installation Guide
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
x
Cisco Integrated Services Router Hardware Installation Guide
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
xi
Cisco Integrated Services Router Hardware Installation Guide
xii
Cisco Integrated Services Router Hardware Installation Guide
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
xiii
Cisco Integrated Services Router Hardware Installation Guide
xiv
Cisco Integrated Services Router Hardware Installation Guide
Warning
When installing the product, please use the provided or designated connection cables/power
cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical
Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown
on the code) for any other electrical devices than products designated by CISCO. The use of cables
that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the
code) is not limited to CISCO-designated products.
Statement 371
Warning
Read the wall-mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people
and damage to the system.
Statement 378
Warning
There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions
. Statement 1015
Warning
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
Statement 1021
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available
. Statement 1024
xv
Cisco Integrated Services Router Hardware Installation Guide
Warning
If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port
to a public network that follows the European Union standards. Connecting the port to this type of
public network can cause severe personal injury or can damage the unit.
Statement 1031
Warning
Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV)
requirements in IEC 60950 based safety standards.
Statement 1033
Warning
Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool.
Statement 1035
Warning
Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
Statement 1036
Warning
Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Statement 1037
Warning
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning.
Statement 1038
Warning
When installing or replacing the unit, the ground connection must always be made first and
disconnected last.
Statement 1046
Warning
Do not locate the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, because they may cause serious injury or death. For
proper installation and grounding of the antenna, please refer to national and local codes (for
example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code,
Section 54).
Statement 1052
Warning
No user-serviceable parts inside. Do not open.
Statement 1073
Warning
Installation of the equipment must comply with local and national electrical codes.
Statement 1074
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
xvi
Cisco Integrated Services Router Hardware Installation Guide
Warning
Read the installation instructions before connecting the system to the power source.
Statement 1004
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning
The covers are an integral part of the safety design of the product. Do not operate the unit without the
covers installed.
Statement 1077
Warning
Hot surface.
Statement 1079
Warning
The equipment is suitable for installation in the following locations
:
Network Telecommunications Facilities
Location where the NEC applies
OSP
Related Documentation
Regulatory Compliance and Safety Information for Cisco 800 Series Routers
Cisco IOS Software Releases 12.4 Special and Early Deployments
Cisco IOS Quality of Service Solutions Command Reference, Release 12.4T
Cisco IOS Security Configuration Guide, Release 12.4T
Cisco IOS Security Command Reference, Release 12.4T
Cisco CP Express User’s Guide
Searching Cisco Documents
To search an HTML document using a web browser, press Ctrl-F (Windows) or Cmd-F (Apple). In most
browsers, the option to search whole words only, invoke case sensitivity, or search forward and backward
is also available.
To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader
Search window (Shift-Ctrl-F). Use the Find toolbar to find words or phrases within a specific document.
Use the Full Reader Search window to search multiple PDF files simultaneously and to change case
sensitivity and other options. Adobe Reader’s online help has more information about how to search PDF
documents.
xvii
Cisco Integrated Services Router Hardware Installation Guide
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS Version 2.0.
xviii
Cisco Integrated Services Router Hardware Installation Guide
CHAPTER
1-1
Cisco Integrated Services Router Hardware Installation Guide
1
Product Overview
This chapter provides an overview of the features available for the Cisco 812, Cisco 819, Cisco 860, 880,
890 Integrated Services Router (ISR) and contains the following sections:
Cisco 810 Series, page 1-1
Cisco 860, 880, 890 Series, page 1-42
Note For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco
800 Series Routers.
Cisco 810 Series
This section contains the following:
Cisco 812 Series, page 1-1
Cisco 819 Series, page 1-10
Cisco 812 Series
This section provides an overview of the features available for the Cisco 812 Integrated Services Router
(ISR) and contains the following sections:
General Description, page 1-1
Hardware Features, page 1-4
SKU Information, page 1-9
Note For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco
800 Series and SOHO Series Routers.
General Description
The Cisco 812 ISR is a new router that looks like an Access Point with 3G, WLAN, and routing
capabilities.
1-2
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
The 3rd Generation (3G) is a generation of standards for mobile technology that facilitates growth,
increased in bandwidth, and supports more diverse applications.
The Cisco 812 ISR can be powered by an (included) external AC adapter or by a PoE+ capable Ethernet
source using an optional Cisco PoE splitter C810-POE-SPL.
A Wireless Local Area Network (WLAN) implements a flexible data communication system frequently
augmenting rather than replacing a wired LAN within a building or campus. WLANs use radio frequency
to transmit and receive data over the air, minimizing the need for wired connections. Figure 1-1 shows
the Cisco 812 ISR.
Figure 1-1 Cisco 812 ISR
344399
1-3
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Figure 1-2 shows the 3G antenna and LEDs display.
Figure 1-2 Cisco 812 ISR 3G and LEDs Display
1
2
43
344400
1 3G diversity antenna 3 WiFi LED
2 3G main antenna 4 3G LED
1-4
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Figure 1-3 shows the I/O side of the Cisco 812 ISR.
Figure 1-3 Cisco 812 ISR I/O Side
Hardware Features
The Cisco 812 ISR supports the following hardware features:
Platform Features, page 1-4
Antenna, page 1-5
LEDs, page 1-5
Memory, page 1-8
Power Supply, page 1-8
Note The WAAS Express feature is not supported. This feature will be supported for 3G and 4G interfaces
with later IOS releases.
Platform Features
The Cisco 812 ISR has the following platform features:
1x GE Enabled WAN (1000/100/10 Base T)
2 TNC connectors for 3G main and diversity antenna (diversity antenna multiplexed with GPS)
512 MB Compact Flash Memory
512 MB DRAM
AC Power Brick (100–264 V and max 0.5 A)
Optional PoE+ (802.3at Class 4) Power Splitter
Built-in Grounding
MAIN
C812G
GE WAN
S L
CON/
AUX
5VDC
4.0A
DIV/GPS
3 421
344393
1 GE WAN port 3 Power connection port
2 Console/Aux port 4 Power switch
1-5
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Ceiling and Wall Mounting Option
LED indicators for the platform
Antenna
The Cisco 812 ISR supports 3G external antenna and WiFi embedded antenna.
3G External Antenna
The Cisco 812 ISR provides two standard panel-mount TNC connectors to support 3G. The main antenna
is used for the primary 3G antenna. The second can be used as a diversity receive only 3G antenna or an
amplified GPS antenna. See Figure 1-2 for the location of the antennas.
WiFi Embedded Antenna
The Cisco 812 ISR supports Dual ports WiFi radios (802.11 a/b/g/n) with embedded 2x3 MIMO.
For compliance and safety information, see the Regulatory Compliance and Safety Information for the
Cisco 800 Series and SOHO Series Routers.
LEDs
The Cisco 812 ISR has two LEDs located on the top side of the router. The 3G LED is located on the
lower right side with respect to the Cisco logo. 3G LED supports multiple functions and colors. The WiFi
LED is located on lower left side with respect to the Cisco logo. Table 1-1 describes the 3G LED for the
Cisco 812 ISR.
Table 1-1 Cisco 812 3G LED Descriptions
ROMMON Mode
3G LED LED Color Description
System Yellow FPGA download is complete.
Green (four blinks) ROMMON is running.
Off No power.
Incomplete FPGA download.
IOS 3G Mode
3G Service Type White MC8700—2G (GPRS/EDGE)
MC5728—1xRTT
Green MC8700—3G (UMTS)
MC5728—EVDO Rev 0
Light Blue MC8700—3.5G (HSPA)
MC5728—EVDO Rev A
Blue MC8700—3.7G (HSPA+)
MC5728—N/A
Off (solid) No service.
1-6
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
RSSI
1
White, Green, Light Blue, or
Blue (solid)
Signal > –60 dBm
Very strong signal
White, Green, Light Blue, or
Blue (three blinks and then a
long pause)
Signal <= –60 to 74 dBm
Strong signal.
White, Green, Light Blue, or
Blue (two blinks and then a long
pause)
Signal <= –75 to –89 dBm
Fair signal.
White, Green, Light Blue, or
Blue (one blink and then a long
pause)
Signal <= –90 to –109 dBm
Marginal signal.
Off Signal <= –110 dBm
Unusable signal.
Fault / Alarm Amber (solid) Fault detected.
Red (four blinks) Temperature alert.
Red (solid) Software failure.
Power cycle.
1. The LED colors of RSSI can be any of the four colors (White, Green, Light Blue, or Blue) listed under 3G service type.
Table 1-1 Cisco 812 3G LED Descriptions (continued)
ROMMON Mode
3G LED LED Color Description
1-7
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Table 1-2 describes the WiFi LED for the Cisco 812 ISR.
Table 1-2 Cisco 812 ISR WiFi LED Descriptions
Message Type Color Description
Boot loader status sequence Blinking Green DRAM memory test in progress.
DRAM memory test is OK.
Board initialization in progress.
Initializing FLASH file system.
Initializing Ethernet.
Ethernet is OK.
Starting Cisco IOS.
Initialization successful.
Association status Green Normal operating condition with no
wireless client associated.
Blue Normal operating condition with at least
one wireless client associated.
Operating status Blinking Blue Software upgrade in progress.
Rapidly cycling through
Blue, Green, Red, and
White
Access point location command invoked.
Blinking Red Ethernet link not operational.
Yellow Router is powered up.
FPGA download is complete.
Blinking Green LED blinks four times when ROMMON is
up.
Boot loader warnings Blinking Blue Configuration recovery in progress.
(MODE button pushed for 2 to 3 seconds)
Red Ethernet failure.
Blinking Green Image recovery in progress (MODE button
released).
Boot loader errors Red DRAM memory test failure.
Blinking Red and Blue FLASH file system failure.
Blinking Red and Off Environment variable failure.
Bad MAC address.
Ethernet failure during image recovery.
Boot environment failure.
No Cisco image file.
Boot failure.
1-8
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Memory
The Cisco 812 ISR supports 512 MB DRAM and 512 MB compact flash memory. The Host router
software runs on the first core. The second core runs the WLAN Access Point software.
If WLAN is not supported in an SKU, all 512 MB DRAM memory is allocated to the first core. For the
SKUs that support WLAN, 128 MB out of the 512 MB main memory is allocated to the second core.
If WLAN is not supported in an SKU, all 512 MB DRAM compact flash memory is allocated to the first
core. For the SKUs that support WLAN, 64 MB out of the 512 MB main memory is allocated to the
second core.
Power Supply
The following are power adapters supported in the Cisco 812 ISR:
AC Power Adapter, page 1-8
PoE+ Splitter, page 1-8
AC Power Adapter
The default configuration is AC adapter that supports up to 4 A of 5 VDC current. The supported AC
power adapter is PWR2-20W-AC that has a nominal input voltage of 100 to 240 VAC.
PoE+ Splitter
The Cisco PoE+ splitter (C810-POE-SPL) splits PoE+ into power and GE. It has connectors built into
the power supply at both input and output so cables can be used at desired length as an option. Figure 1-4
shows the I/O side of the PoE+ splitter.
Cisco IOS errors Red Software failure. Try to disconnect and
reconnect the unit power.
Cycling through Blue,
Green, Red, and Off
General warning.
Table 1-2 Cisco 812 ISR WiFi LED Descriptions (continued)
Message Type Color Description
1-9
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Figure 1-4 PoE+ Splitter I/O Side
SKU Information
Table 1-3 lists the different SKUs available for the Cisco 812 ISR. The AP802-AGN-X-K9 (WLAN PID)
is integrated as part of the router for the SKUs that support WLAN and is not orderable separately.
OUTPUT
OUTPUT
65 521
3 4
345067
1 Grounding location 4 PoE+ input
2 Power status LED 5 Openings for power cord latch to lock into
enclosure
3 GE0 output 6 Input power connection
Table 1-3 Supported SKUs
SKU ID WLAN PID Description
C812G+7-K9 C812 Secure Router Standalone Unit (non-US) 3.7G HSPA
+ Release 7 with SMS/GPS
WLAN is not supported.
C812G-CIFI+7-E-K9 AP802-AGN-E-K9 C812 Secure Router (non-US) 3.7G HSPA + Release 7 with
SMS/GPS and Dual WiFi Radio with ETSI
C812G-CIFI+7-N-K9 AP802-AGN-N-K9 C812 Secure Router (non-US) 3.7G HSPA + Release 7 with
SMS/GPS and Dual WiFi Radio with ANZ
C812G-CIFI-V-A-K9 AP802-AGN-A-K9 C812 Secure Router for Verizon EV-DO Rev A with
SMS/GPS and Dual WiFi Radio with FCC
C812G-CIFI-S-A-K9 AP802-AGN-A-K9 C812 Secure Router for Sprint EV-DO Rev A with
SMS/GPS and Dual WiFi Radio with FCC
1-10
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Cisco 819 Series
This section provides an overview of the features available for the Cisco 819 and Cisco 819H Integrated
Services Routers (ISRs) and contains the following sections:
General Description, page 1-10
SKU Information, page 1-14
Hardware Features, page 1-27
Note Cisco 819 is used to refer to Cisco 819HG, Cisco 819G, Cisco 819H, Cisco 819GW, Cisco 819HGW,
Cisco 819HWD, Cisco 819HG-4G, and Cisco 819G-4G ISRs unless specifically called out otherwise.
Note This product is a Class 1 Outside Plant (OSP) as per Telcordia GR-3108.
Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap
that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and
SOHO Series Routers.
General Description
The Cisco 819 Integrated Services Router, part of the Cisco Integrated Services Routers Generation 2
(ISR G2) Family designed in compact hardened and non-hardened form factors, is the smallest Cisco
IOS Software router with support for integrated fourth-generation (4G LTE) and third-generation (3G)
wireless WAN (mobile broadband backhaul). The Cisco 819GW now supports Dual 802.11 a/b/g/n
radios WiFi. The Cisco 819 ISR machine-to-machine gateway provides a rapidly deployable, highly
available, reliable, and secure solution into machine-to-machine applications for financial, telemetry,
utility, retail, industrial automation, and transportation with comprehensive management capability.
Transparently integrated into Cisco IOS Software as an enterprise-class feature, the Cisco 819 Hardened
ISR provides highly secure data, voice, and video communications to stationary and mobile network
nodes across wired and wireless links.
Available in both non-hardened (Cisco 819G) and hardened (Cisco 819HG) versions, the Cisco 819
supporting 4G LTE and 3G wireless WAN (WWAN) speeds offers a cost-effective, rapidly deployable,
reliable, and secure primary or backup solution. With support for industrial-grade components, the
hardened Cisco 819HG extends the ISR machine-to-machine gateway footprint and provides the
flexibility for deployment in many different stationary and mobile environments where space, heat
dissipation, exposure to extreme temperatures, harsher environments, and low power consumption are
critical factors. For mobile applications, Mobile IP delivers transparent roaming across multiple wireless
networks capable of covering wide geographic areas.
The Cisco 819 ISR is a standard form factor with a commercial operating range. The 3G Cisco 819 ISRs
support the 3G speeds (High-Speed PacketAccess Plus [HSPA+] enabling up to 4G speeds and Evolution
Data Optimized [EVDO Rev A]). They are backward-compatible with High-Speed Packet Access
(HSPA), Universal Mobile Telecommunications Service (UMTS), Enhanced Data Rates for Global
Evolution (EDGE), General Packet Radio Service (GPRS), and EVDO Rev 0/1xRTT.
1-11
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
The 4G LTE C819 supports the latest Third-Generation Partnership Project (3GPP) Release 8 LTE
standards. The Cisco 4G multimode LTE WWAN C819 provides persistent and reliable LTE connectivity
with fallback and transparent handoff to earlier technologies. The Cisco 819HG-4G and Cisco 819G-4G
support multimode 4G LTE and have embedded Sierra Wireless multimode modem.
The Cisco 819 ISR is a desktop form factor with built-in wall-mount features, floor mount, and DIN rail
mount features in selected SKUs. These routers are powered by an external AC power or optional DC
adapter. Figure 1-5 shows the Cisco 819HG ISR.
The Cisco 819GW ISRs support WiFi radios with a higher memory density and a new barrel-type power
connector. A Wireless Local Area Network (WLAN) implements a flexible data communication system
frequently augmenting rather than replacing a wired LAN within a building or campus. WLANs use
radio frequency to transmit and receive data over the air, minimizing the need for wired connections.
Figure 1-6 shows the Cisco 819HGW ISR.
The Cisco 819GW ISRs have the following additional features:
Dual 802.11 a/b/g/n radios
External WiFi antenna
WLAN LED
Figure 1-5 Cisco 819HG Integrated Services Router
283010
1-12
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Figure 1-6 Cisco 819HGW Integrated Services Router
Figure 1-7 shows the front panel details of the Cisco 819HG ISR.
Figure 1-7 Cisco 819HG ISR Front Panel
285479
1 3G main antenna 7 FE ports
2 LEDs 8 GE WAN port
3 Reset button 9 Console/Aux port
1-13
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Figure 1-8 shows the front panel details of the Cisco 819HGW ISR.
Figure 1-8 Cisco 819HGW ISR Front Panel
4 3G mini-USB diagnostic port 10 5 VDC molex power input
5 Diversity/GPS antenna 11 Power switch
6 12-in-1 serial port 12 Ground
344077
21 43 6 7 9 10 11 12
5 8
1 3G main antenna 7 FE ports
2 LEDs 8 GE WAN port
3 Reset button 9 Console/Aux port
4 3G mini-USB diagnostic port 10 5 VDC barrel-type power input
5 Diversity/GPS antenna 11 Power switch
6 12-in-1 serial port 12 Ground
1-14
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Figure 1-9 shows the front panel details of the Cisco 819 4G LTE ISR.
Figure 1-9 Cisco 819 4G LTE ISR Front Panel
SKU Information
Table 1-4 lists the different 3G SKUs available for the Cisco 819HG and Cisco 819G ISRs. All SKUs
support external antenna.
Note WLAN is not supported.
285447
1 43 6 7 9 10 11 13
5 128
2
1 4G antenna connector—M0/MAIN 8 GE WAN port
2 LEDs 9 Console/Aux port
3 Reset button 10 Power input
4 4G/3G port 11 Power switch
5 4G antenna connector—M1/DIV 12 Active GPS antenna connector
6 Serial port 13 Ground
7 FE ports
Table 1-4 Supported 3G SKUs for Cisco 819HG and Cisco 819G ISRs
SKU ID Description
C819HG+7-K9 Compact Hardened 3G IOS Router with Global HSPA + Release 7 based on
MC8705
C819HG-U-K9 Compact Hardened 3G IOS Router with GLOBAL HSPA Release 6 based on
MC8795V
C819HG-V-K9 Compact Hardened 3G IOS Router with Verizon EVDO Rev A based on
MC5728V
C819HG-S-K9 Compact Hardened 3G IOS Router with Sprint EVDO Rev A based on
MC5728V
1-15
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
C819HG-B-K9 Compact Hardened 3G IOS Router with Bharat generic EVDO Rev A based
on MC5728V
C819G+7-K9 Compact Non-hardened 3G IOS Router with Global HSPA + Release 7 based
on MC8705
C819G-U-K9 Compact Non-hardened 3G IOS Router with GLOBAL HSPA Release 6
based on MC8795V
C819G-V-K9 Compact Non-hardened 3G IOS Router with Verizon EVDO Rev A based on
MC5728V
C819G-S-K9 Compact Non-hardened 3G IOS Router with Sprint EVDO Rev A based on
MC5728V
C819G-B-K9 Compact Non-hardened 3G IOS Router with Bharat generic EVDO Rev A
based on MC5728V
Table 1-4 Supported 3G SKUs for Cisco 819HG and Cisco 819G ISRs (continued)
SKU ID Description
1-16
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Table 1-5 lists the different SKUs available for the Cisco 819HGW, Cisco 819H, and Cisco 819HWD
ISRs.
Table 1-5 Supported SKUs for Cisco 819HGW, Cisco 819H, and Cisco 819HWD ISRs
SKU ID WLAN ID
WiFi External Antenna
Support Description
C819HGW+7-E-K9 AP802H-AGN-E-K9 Yes Cisco 819 Secure Hardened M2M
GW (non-US) 3.7G HSPA + Release
7 with SMS/GPS and Dual WiFi
Radio with ETSI
C819HGW+7-N-K9 AP802H-AGN-N-K9 Yes Cisco 819 Secure Hardened M2M
GW (non-US) 3.7G HSPA + Release
7 with SMS/GPS and Dual WiFi
Radio with ANZ
C819HGW+7-A-A-K9 AP802H-AGN-A-K9 Yes Cisco 819 Secure Hardened M2M
GW (North America) 3.7G HSPA +
Release 7 with SMS/GPS and Dual
WiFi Radio with FCC for ATT
C819HGW-V-A-K9 AP802H-AGN-A-K9 Yes Cisco 819 Secure Hardened Router
for Verizon EV-DO Rev A with
SMS/GPS and Dual WiFi Radio with
FCC
C819HGW-S-A-K9 AP802H-AGN-A-K9 Yes Cisco 819 Secure Hardened Router
for Sprint EV-DO Rev A with
SMS/GPS and Dual WiFi Radio with
FCC
C819H-K9 Cisco 819 Secure Hardened Router
with Serial
WLAN and 3G are not supported
C819HWD-E-K9 AP802H-AGN-E-K9 Yes Cisco 819 Secure Hardened Router
and Dual WiFi Radio with ETSI
3G is not supported
C819HWD-A-K9 AP802H-AGN-A-K9 Yes Cisco 819 Secure Hardened Router
and Dual WiFi Radio with FCC
3G is not supported
1-17
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Table 1-6 lists the different 4G LTE SKUs available for the Cisco 819HG and Cisco 819G ISRs.
Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs
SKU ID Mode Operating Regions Frequency Band Description
C819HG-4G-V-K9 LTE—DOrA North America 700 MHz (band 13) or LTE
800/1900 MHz for CDMA
1xRTT, 1xEVDO Rev A
Compact Hardened Cisco
819 router with multi
mode LTE feature
dedicated to Verizon
Wireless networks. This
comes with a Sierra
Wireless MC7750
modem.
C819G-4G-V-K9 LTE—DOrA North America 700 MHz (band 13) for LTE
800/1900 MHz for CDMA
1xRTT, 1xEVDO Rev A
Compact Non-hardened
Cisco 819 router with
multi mode LTE feature
dedicated to Verizon
Wireless networks. This
comes with a Sierra
Wireless MC7750
modem.
C819HG-4G-A-K9 LTE—HSPA+/
HSPA/UMTS/
EDGE/GPRS
North America 700 MHz (band 17)/AWS (band
4)/2100MHz (band 1) for LTE
800/850/1900/2100 MHz for
UMTS/ HSPA+/HSPA
850/900/1800/1900 MHz for
GSM/EDGE/GPRS
Compact Hardened Cisco
819 router with multi
mode LTE feature
dedicated to AT&T
Wireless networks. This
comes with a Sierra
Wireless MC7700
modem.
C819G-4G-A-K9 LTE—HSPA+/
HSPA/UMTS/
EDGE/GPRS
North America 700 MHz(band 17)/AWS(band
4)/2100MHz(band 1) for LTE
800/850/1900/2100 MHz for
UMTS/ HSPA+/HSPA
850/900/1800/1900 MHz for
GSM/EDGE/GPRS
Compact Non-hardened
Cisco 819 router with
multi mode LTE feature
dedicated to AT&T
Wireless networks. This
comes with a Sierra
Wireless MC7700
modem.
C819HG-4G-G-K9 LTE—HSPA+/
HSPA/UMTS/
EDGE/GPRS
Global 800 MHz (band 20)/900 MHz
(band 8)/1800 MHz (band
3)/2100 MHz (band 1)/2600
MHz (band 7) for LTE
900/2100 MHz for UMTS/
HSPA+/HSPA
900/1800/1900 MHz for
GSM/EDGE/GPRS
Hardened Cisco 819
router with multi-mode
LTE feature for global
wireless networks. This
comes with a Sierra
Wireless MC7710
modem.
1-18
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
C819G-4G-GA-K9 LTE—HSPA+/
HSPA/UMTS/
EDGE/GPRS
Global (Europe,
Australia and New
Zealand)
LTE—800 MHz (band 20)/900
MHz (band 8)/1800 MHz (band
3)/2100 MHz (band 1)/2600
MHz (band 7)
3G—800 MHz (band 6)/850
MHz (band 5)/900 MHz (band 8)
/1900 MHz (band 2) 2100 MHz
(band 1) for UMTS/
HSPA+/HSPA
2G—850/900/1800/1900 MHz
for GSM/EDGE/GPRS
Non-hardened Cisco 819
router with multi-mode
LTE feature for global
wireless networks. This
comes with a Sierra
Wireless MC7304
modem.
C819G-4G-NA-K9
LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
North America
(AT&T,
Bell-Canada,
Roger, Telus, and
other GSM/LTE
operators in USA
and Canada)
LTE:
AWS (band 4)
700 MHz (band 5)
850 MHz (band 17)
1900 MHz (band 2)
2600 MHz (band 7)
UMTS, HSPA+, HSPA:
1900 MHz (band 2)
AWS (band 4)
850 (band 5)
GSM, EDGE, GPRS:
850 MHz
900 MHz
1800 MHz
1900 MHz
Non-hardened Cisco 819
router with multi-mode
LTE feature for AT & T
wireless networks. This
comes with a Sierra
Wireless MC7354 modem
Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)
SKU ID Mode Operating Regions Frequency Band Description
1-19
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
C819G-4G-ST-K9 LTE
EVDO Rev-A
1xRTT
North America
(Sprint)
LTE:
AWS (band 4)
700 MHz (band 13)
PCS 1900 MHz (band 25)
3G:
800 MHz (band class 0)
1900 MHz (band class 1)
800 MHz (band class 10)
2G:
800 MHz (band class 0)
1900 MHz (band class 1)
800 MHz (band class 10)
Non-hardened Cisco 819
router with multi-mode
LTE feature for Sprint
wireless networks. This
comes with a Sierra
Wireless MC7350
modem.
C819G-4G-VZ-K9
LTE
EVDO Rev-A
1xRTT
North America
(Verizon)
LTE:
AWS (band 4)
700 MHz (band 13)
PCS 1900 MHz (band 25)
3G:
800 MHz (band class 0)
1900 MHz (band class 1)
800 MHz (band class 10)
2G:
800 MHz (band class 0)
1900 MHz (band class 1)
800 MHz (band class 10)
Non-hardened Cisco 819
router with multi-mode
LTE feature for Verizon
wireless networks. This
comes with a Sierra
Wireless MC7350
modem.
Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)
SKU ID Mode Operating Regions Frequency Band Description
1-20
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
C819GW-LTE-MN
A-AK9
LTE
HSPA+
EVDO
Revision A
(DOrA)
CDMA
EDGE/GPRS/G
SM
North America For LTE:
700 MHz (Band 13)
700 MHz (Band 17)
800 MHz (Band 5)
1900 MHz (Band 2)
1900 MHz (Band 25)
AWS 1700/2100 MHz
(Band 4)
For HSPA+:
850 MHz (Band 5)
900 MHz (Band 8)
1900 MHz (Band 2)
2100 MHz (Band 1)
AWS 1700/2100 MHz
(Band 4)
For CDMA and EVDO Revision
A:
800 MHz (Band Class 0)
1900 MHz (Band Class 1)
800 MHz (Band Class 10)
For EDGE/GPRS/GSM:
850 MHz
900 MHz
1800 MHz
1900 MHz
C819GW-LTE-MNA-AK
9 is a dedicated
Multimode LTE SKU for
North American wireless
networks and comes with
a Sierra Wireless
MC7354MNA modem.
C819GW-LTE-MNA-AK
9 is a non-hardened Cisco
819 Series Router.
For 3GPP compliance, the
extended temperature
range for this SKU is -15
to 50C. For non-3GPP
compliance, it is -15 to
55C.
Dual SIMs in this SKU
provide high reliability
and cellular multihoming
support for LTE and
HSPA-based networks
using the common FW
technology within the
same region. Dual SIMs
in the North American
SKUs provide switchover
with different FW
technology.
Note This is a 4G+
WiFi SKU. This
SKU supports all
North American
carriers like
Verizon, ATT,
Sprint, and
Canada using
MC7354MNA
modems.
Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)
SKU ID Mode Operating Regions Frequency Band Description
1-21
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
C819G-LTE-MNA-
K9
LTE
HSPA+
EDGE/GPRS/G
SM
CDMA
EVDO
North America LTE:
850MHz(band 19)
1500MHz(band 21)
2100MHz(band 1)
3G(UMTS,HSPA+,HSPA):
800MHz(band 6)
850MHz(band 5)
850MHz(band 19)
2100MHz(band 1)
2G(GSM,EDGE,GPRS):
850MHz
900MHz
1800MHz
1900MHz
C819G-LTE-MNA-K9 is
a dedicated Multimode
LTE SKU for global
wireless network and
comes with a Sierra
Wireless MC7354-MNA
modem.
C819G-LTE-MNA-K9 is
a non-hardened Cisco 819
Series Router.
For 3GPP compliance, the
extended temperature
range for this SKU is -15
to 50C. For non-3GPP
compliance, it is -15 to
55C.
Dual SIMs in this SKU
provide high reliability
and cellular multihoming
support for LTE and
HSPA-based networks
using the common FW
technology within the
same region. Dual SIMs
provide switchover with
different FW technology.
Note This SKU does
not have a WiFi
module.
Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)
SKU ID Mode Operating Regions Frequency Band Description
1-22
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
C819HG-LTE-MNA
-K9
LTE
HSPA+
EDGE/GPRS/G
SM
CDMA
EVDO
North America LTE:
AWS (band 4)
850MHz(band 19)
1500MHz(band 21)
2100MHz(band 1)
3G(UMTS,HSPA+,HSPA):
800MHz(band 6)
850MHz(band 5)
850MHz(band 19)
2100MHz(band 1)
2G(GSM,EDGE,GPRS):
850MHz
900MHz
1800MHz
1900MHz
C819HG-LTE-MNA-K9
is a dedicated Multimode
LTE SKU for North
American wireless
networks and comes with
a Sierra Wireless
MC7354-MNA modem.
C819G-LTE-MNA-K9 is
a hardened Cisco 819
Series Router.
For 3GPP compliance, the
extended temperature
range for this SKU is -15
to 50C. For non-3GPP
compliance, it is -15 to
55C.
Dual SIMs in this SKU
provide high reliability
and cellular multihoming
support for LTE and
HSPA-based networks
using the common FW
technology within the
same region. Dual SIMs
provide switchover with
different FW technology.
Note This SKU does
not have a WiFi
module.
Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)
SKU ID Mode Operating Regions Frequency Band Description
1-23
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
C819G-LTE-LA-K9 LTE
HSPA+
HSPA
UMTS
Latin
America/APAC
For FDD LTE:
700 MHz (band 28)
850 MHz (band 5)
800 MHz (band 19)
800 MHz (band 18)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
For TDD LTE:
1900 MHz (Band 39)
2300 MHz (Band 40)
2500 MHz (Band 41)
2600 MHz (Band 38)
For UMTS, HSPA+, HSPA:
800 MHz (band 6)
800 MHz (band 19)
850 MHz (band 5)
900 MHz (band 8)
1700 MHz (band 9)
2100 MHz (band 1)
C819G-LTE-LA-K9 is a
dedicated Multimode LTE
SKU for Latin American
wireless networks and
comes with a Sierra
Wireless MC7430
modem.
Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)
SKU ID Mode Operating Regions Frequency Band Description
1-24
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
C819GW-LTE-LA-
CK9
LTE
HSPA+
HSPA
UMTS
Latin
America/APAC
For FDD LTE:
700 MHz (band 28)
850 MHz (band 5)
800 MHz (band 19)
800 MHz (band 18)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
For TDD LTE:
1900 MHz (Band 39)
2300 MHz (Band 40)
2500 MHz (Band 41)
2600 MHz (Band 38)
For UMTS, HSPA+, HSPA:
800 MHz (band 6)
800 MHz (band 19)
850 MHz (band 5)
900 MHz (band 8)
1700 MHz (band 9)
2100 MHz (band 1)
C819G-LTE-LA-CK9 is a
dedicated Multimode LTE
SKU for Latin American/
APAC wireless networks
and comes with a Sierra
Wireless MC7430
modem.
C819GW-LTE-LA-CK9
comes with WiFi-C
802.11n dual radio.
Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)
SKU ID Mode Operating Regions Frequency Band Description
1-25
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
C819GW-LTE-LA-
QK9
LTE
HSPA+
HSPA
UMTS
Latin
America/APAC
For FDD LTE:
700 MHz (band 28)
850 MHz (band 5)
800 MHz (band 19)
800 MHz (band 18)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
For TDD LTE:
1900 MHz (Band 39)
2300 MHz (Band 40)
2500 MHz (Band 41)
2600 MHz (Band 38)
For UMTS, HSPA+, HSPA:
800 MHz (band 6)
800 MHz (band 19)
850 MHz (band 5)
900 MHz (band 8)
1700 MHz (band 9)
2100 MHz (band 1)
C819GW-LTE-LA-QK9
is a dedicated Multimode
LTE SKU for Latin
American / APAC
wireless networks and
comes with a Sierra
Wireless MC7430
modem.
C819GW-LTE-LA-QK9
comes with WiFi-Q
802.11n dual radio.
Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)
SKU ID Mode Operating Regions Frequency Band Description
1-26
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Re-branding of C8xx-B and EHWIC-3G-EVDO-B
The C881G-B-K9, C819G-B-K9, and EHWIC-EVDO-B (Bharat) SKUs are introduced as an umbrella
SKU to cover BSNL, Tata, and Reliance service providers in India.
Software based mechanism is introduced to identify specific carrier.
Carrier ID and name are displayed under "show cellular <unit> hardware".
The software mechanism is backward compatible with other existing CDMA SKUs such as
HWIC-3G-CDMA(-S,-V) and PCEX-3G-CDMA(-S,-V).
Cisco IOS Requirement
15.3(2)T, 15.3(3)M or later. New MIB objects for carrier ID and name will be introduced in later release.
Sample CLI Output
Router#show cellular 0/0/0 hardware
Modem Firmware Version = p2813301
Modem Firmware built = 06-24-10
Hardware Version = MC5728V Rev 1.0
C819GW-LTE-LA-
NK9
LTE
HSPA+
HSPA
UMTS
Latin America /
APAC
For FDD LTE:
700 MHz (band 28)
850 MHz (band 5)
800 MHz (band 19)
800 MHz (band 18)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
For TDD LTE:
1900 MHz (Band 39)
2300 MHz (Band 40)
2500 MHz (Band 41)
2600 MHz (Band 38)
For UMTS, HSPA+, HSPA:
800 MHz (band 6)
800 MHz (band 19)
850 MHz (band 5)
900 MHz (band 8)
1700 MHz (band 9)
2100 MHz (band 1)
C819GW-LTE-LA-NK9
is a dedicated Multimode
LTE SKU for Latin
American / APAC
wireless networks and
comes with a Sierra
Wireless MC7430
modem.
C819GW-LTE-LA-NK9
comes with WiFi-N
802.11n dual radio.
Table 1-6 Supported 4G LTE SKUs for Cisco 819HG-4G and Cisco 819G-4G ISRs (continued)
SKU ID Mode Operating Regions Frequency Band Description
1-27
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Electronic Serial Number (ESN) = 0x60E62C87 [09615084679] Preferred Roaming List (PRL)
Version = 10 PRI SKU ID = 535479 Carrier ID = 19 Carrier Name = Reliance Current Modem
Temperature = 30 degrees Celsius Endpoint Port Map = 75
Router#
Router#show cellular 0/1/0 hardware
Modem Firmware Version = p2813301
Modem Firmware built = 06-24-10
Hardware Version = MC5728V Rev 1.0
Electronic Serial Number (ESN) = 0x60E62431 [09615082545] Preferred Roaming List (PRL)
Version = 10 PRI SKU ID = 535479 Carrier ID = 29 Carrier Name = Tata Current Modem
Temperature = 30 degrees Celsius Endpoint Port Map = 75
Router#
Hardware Features
This section provides an overview of the following hardware features for the Cisco 819 ISR.
Platform Features for Cisco 819 ISRs, page 1-27
Antennas, page 1-29
Power Switch, page 1-29
Reset Button, page 1-30
LEDs, page 1-30
Memory, page 1-34
Embedded 3G Modem, page 1-34
Embedded 4G LTE Modem, page 1-34
SIM Card, page 1-34
Supported Cisco Antennas and Cables, page 1-35
Serial Port, page 1-40
Power Supply, page 1-41
Accessories, page 1-42
Note The WAAS Express feature is not supported. This feature will be supported for 3G and 4G interfaces
with later IOS releases.
Platform Features for Cisco 819 ISRs
Table 1-7 lists the platform features comparison for the Cisco 819 ISRs.
1-28
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Table 1-7 Cisco 819 ISRs Platform Features
Platform Features
Cisco 819HG
Cisco 819G
(with 3G)
Cisco 819HGW
Cisco 819HWD
(with 3G and WiFi)
Cisco 819HG-4G
Cisco 819G-4G
(with 4G LTE)
Cisco 819GW
(with 4G LTE and WiFi)
512 MB DRAM Yes
1 GB DRAM Yes Yes Yes
1 Gigabit Ethernet
WAN port
Yes Yes Yes Yes
12-in-1 serial
interface
Yes Yes Yes Yes
256 KB of NVRAM
storage
Yes Yes Yes Yes
256 Compact Flash
support in IDE mode
(internal)
Yes
1 GB Compact Flash
support in IDE mode
(internal)
—YesYesYes
Cisco EnergyWise Yes Yes Yes
Dual 802.11 a/b/g/n
Radios with Cisco
DFS, CleanAir, and
Client Link support
—Yes Yes
Embedded 3G
modem
Yes Yes
Embedded 4G LTE
modem
—— YesYes
Environmental
monitoring and
temperature logging
Yes Yes Yes
Four ports FE
interconnect switch
support
Yes Yes Yes Yes
LED indicators for
the platform
Yes Yes Yes Yes
Onboard crypto
acceleration
Yes Yes Yes Yes
Power cord retention
lock
—YesYesYes
Power switch lock Yes Cisco 819HG-4G ISRs
only
Yes
Reset button Yes Yes Yes Yes
1-29
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Antennas
The Cisco 819 3G routers provide two standard panel-mount TNC connectors to support the 3G antenna
and the diversity and GPS external antenna. The main antenna is used for the primary 3G antenna. The
second can be used as a diversity receive only 3G antenna or GPS antenna that does not require power
supply from the router.
The Cisco 819 4G routers provide two standard panel-mount TNC connectors on the router front panel
for the main and diversity antennas. The main antenna connector is used for the primary 4G antenna. The
second antenna connector can be used as a diversity receive only 4G antenna. An SMA connector for
active GPS antenna is also available on the front panel of the router.
The Cisco 819HGW and Cisco 819HWD ISRs also support Cisco WiFi external antennas. See the
“Supported Cisco Antennas and Cables” section on page 1-35 for more information.
WiFi External Antenna
The external WiFi antenna is used to support better WiFi coverage. All external antenna supports the
following:
Dual 802.11 a/b/g/n radios
2x3 MIMO
Omnidirectional
Power Switch
The power switch shuts down the router. A power switch lock is available to prevent accidental turning
off of the router in the hardened SKUs.
Real Time Clock
(RTC)
1
Yes Yes Yes Yes
ScanSafe Yes Yes Yes
Single console/AUX
port
Yes Yes Yes Yes
SNMP Yes Yes Yes
TFTP support with
Ethernet WAN
interface
Yes Yes
Warm reload Yes Yes Yes
1. A real-time clock (RTC) with battery backup provides date and time when the system is powered on. The RTC is used to verify the validity of the
Certification Authority stored on the router.
Table 1-7 Cisco 819 ISRs Platform Features (continued)
Platform Features
Cisco 819HG
Cisco 819G
(with 3G)
Cisco 819HGW
Cisco 819HWD
(with 3G and WiFi)
Cisco 819HG-4G
Cisco 819G-4G
(with 4G LTE)
Cisco 819GW
(with 4G LTE and WiFi)
1-30
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Reset Button
The Reset button resets the router configuration to the default configuration set by the factory. To restore
the router configuration to the default configuration set by the factory, use a standard size #1 paper clip
with wire gauge 0.033 inch or smaller and simultaneously press the reset button while applying power
to the router.
LEDs
The LEDs are located on the front panel of the router. Table 1-8 describes the 3G LEDs for the Cisco
819 ISR.
Table 1-8 3G LED Descriptions
LED Color Description
SYS Yellow FPGA download is complete.
Green (blinking) ROMMON is operational.
Green (solid) IOS is operational.
Green (four blinks
during bootup)
Reset button has been pushed during the bootup.
Off After powering up, when FPGA is being downloaded (in
ROMMON).
ACT Green (blinking) Network activity on FE Switch ports, GE WAN port, 3G
cellular interface, and serial interfaces.
Off No network activity.
WWAN Green Module is powered on and connected but not transmitting
or receiving.
Green (slow blinking) Module is powered on and searching for connection.
Green (fast blinking) Module is transmitting or receiving.
Off Module is not powered.
GPS Green (solid) Standalone GPS.
Green (slow blinking) GPS is acquiring.
Yellow (solid) Assisted GPS.
Yellow (slow blinking) Assisted GPS is acquiring.
Off GPS is not configured.
1-31
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Table 1-9 describes the WLAN LEDs for the Cisco 819HGW and Cisco 819HWD ISRs.
RSSI Green (solid) Signal > –60 dBm
Very strong signal
Green (three blinks and
then a long pause)
Signal <= –60 to 74 dBm
Strong signal
Green (two blinks and
then a long pause)
Signal <= –75 to –89 dBm
Fair signa
Green (one blink and
then a long pause)
Signal <= –90 to –109 dBm
Marginal signal
Off Signal <= –110 dBm
Unusable signal
SIM
1,2
Green / Yellow (one
green blink followed by
two yellow blinks)
SIM in slot 0 active, SIM in slot 1 is not.
Yellow / Green (one
yellow blink followed
by two green blinks)
SIM in slot 1 active, SIM in slot 0 is not.
Off / Green (two green
blinks and then a pause)
No SIM in slot 0, SIM present in slot 1.
Green / Off (Slow single
green blink and then a
pause
SIM present in slot0, no SIM in slot 1.
Off / Off No SIM present in either slots.
3G Green (one blink and
then a pause)
For 1xRTT, EGPRS, or GPRS service.
Green (two blinks and
then a pause)
For EVDO, EVDO/1xRTT, or UMTS.
Green (three blinks and
then a pause)
For EVDO/1xRTT RevA, HSPA, or HSUPA/HSDPA.
Green (solid) For HSPA PLUS.
Off No Service.
1. Not applicable to Verizon and Sprint EVDO modems.
2. There is only one LED to indicate the status of two SIMs. A one-blink pattern represents the status of the SIM in slot 0,
followed by a two-blink pattern for the SIM in slot 1.
Table 1-8 3G LED Descriptions (continued)
LED Color Description
1-32
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Table 1-10 describes the 4G LTE LEDs for the Cisco 819 ISR.
Table 1-9 WLAN LED Descriptions
WLAN LED Color Description
Boot loader status
sequence
Blinking Green Board initialization in progress.
Initializing FLASH file system.
Initializing Ethernet.
Ethernet is OK.
Starting Cisco IOS.
Initialization is successful.
Association status Green Normal operating condition with no
wireless client associated.
Blue Normal operating condition with at least
one wireless client associated.
Operating status Blinking Blue Software upgrade in progress.
Rapidly cycling through
Green, Red, and White
Access point location command invoked.
Blinking Red Ethernet link is not operational.
Boot loader errors Blinking Red and Blue FLASH file system failure.
Blinking Red and Off Environment variable failure.
Bad MAC address.
Ethernet failure during the image recovery.
Boot environment failure.
No Cisco image file.
Boot failure.
Cisco IOS errors Red Software failure. Try to disconnect and
reconnect the unit power.
Table 1-10 4G LTE LED Descriptions
LED Color Description
SYS Yellow FPGA download is complete.
Green (blinking) ROMMON is operational.
Green (solid) IOS is operational.
Green (four blinks
during bootup)
Reset button has been pushed during the bootup.
Off After powering up, when FPGA is being downloaded (in
ROMMON).
1-33
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
ACT Green (blinking) Network activity on FE Switch ports, GE WAN port, 3G
cellular interface, and serial interfaces.
Off No network connectivity.
WWAN Green Module is powered on and connected but not
transmitting or receiving.
Green (slow blinking) Module is powered on and searching for connection.
Green (fast blinking) Module is transmitting or receiving.
Off Module is not powered.
GPS Green (solid) Standalone GPS.
Green (slow blinking) GPS is acquiring.
Yellow (solid) Assisted GPS.
Yellow (slow blinking) Assisted GPS is acquiring.
Off GPS is not configured.
RSSI Green (solid) Signal > –60 dBm
Very strong signal
Green (three blinks and
then a long pause)
Signal <= –60 to 74 dBm
Strong signal
Green (two blinks and
then a long pause)
Signal <= –75 to –89 dBm
Fair signal
Green (one blink and
then a long pause)
Signal <= –90 to –109 dBm
Marginal signal
Off Signal <= –110 dBm
Unusable signal
SIM Green / Yellow (one
green blink followed by
two yellow blinks)
SIM in slot 0 is active, SIM in slot 1 is not.
Yellow / Green (one
yellow blink followed
by two green blinks)
SIM in slot 1 is active, SIM in slot 0 is not.
Off / Green (two green
blinks and then a pause)
No SIM in slot 0, SIM present in slot 1.
Green / Off (Slow single
green blink and then a
pause)
SIM present in slot 0, no SIM in slot 1.
Off / Off No SIM present in either slots.
Table 1-10 4G LTE LED Descriptions (continued)
LED Color Description
1-34
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Memory
The Cisco 819HG and Cisco 819G ISRs uses non-upgradable flash memory and main memory. The
onboard flash memory contains the Cisco IOS software image and the boot flash contains the ROMMON
boot code. Table 1-11 lists the memory requirements for Cisco 819 ISRs.
Embedded 3G Modem
The 3G cellular interface is the primary WAN data link, but it can also be used as a backup data link.
The 3G technology is third-generation wide-area cellular technology that is used in broadband wireless
data in a mobile environment.
Embedded 4G LTE Modem
The Cisco 819HG-4G and Cisco 819G-4G routers have an embedded 4G LTE modem provided by Sierra
Wireless. The Verizon SKUs come with an MC7750 modem, the AT&T SKUs come with an MC7700
modem, and the Global SKUs come with an MC7710 modem.
SIM Card
Table 1-12 lists the SIM Card slots available for Cisco the 819 ISRs.
3G/4G Green (one blink and
then a pause)
For 1xRTT, EGPRS, or GPRS service.
Green (two blinks and
then a pause)
For EVDO, EVDO/1xRTT, or UMTS service.
Green (three blinks and
then a pause)
For EVDO/1xRTT RevA, HSPA, or HSUPA/HSDPA
service.
Green (four blinks and
then a pause)
For HSPA+ service.
Green (Solid) For 4G/LTE service.
Off No Service.
Table 1-10 4G LTE LED Descriptions (continued)
LED Color Description
Table 1-11 Memory Requirements for Cisco 819 ISRs
Memory Requirements
Cisco 819HG
Cisco 819G
(with 3G)
Cisco 819HGW
Cisco 819HWD
(with WiFi)
Cisco 819HG-4G
Cisco 819G-4G
(with 4G LTE)
256 Compact Flash support in
IDE mode (internal)
Yes
1 GB Compact Flash support in
IDE mode (internal)
—YesYes
512 MB DRAM Yes
1 GB DRAM Yes Yes
1-35
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Supported Cisco Antennas and Cables
The Cisco 819 ISR provides two standard panel-mount TNC connectors to support the 3G antenna and
the diversity and GPS external antenna. The main antenna is used for the primary 3G antenna. The
second can be used as a diversity receive only 3G antenna or GPS antenna that does not require power
supply from the router.
Note A Lightning Arrestor must be used when you install antenna outdoor. Note that the center conductor is
not protected under 200V (sparkover voltage nominal value).
Table 1-12 SIM Card Slot
Two Internal SIM Card Slots One Internal SIM Card Slot No SIM Card Slot
C819G-U-K9 C819HG-4G-V-K9 C819HG-V-K9
C819G+7-K9 C819G-4G-V-K9 C819HG-S-K9
C819HG-U-K9 C819HG-4G-A-K9 C819G-V-K9
C819HG+7-K9 C819G-4G-A-K9 C819G-S-K9
C819HGW+7-A-A-K9 C819G-4G-VZ-K9 C819HGW-V-A-K9
C819HGW+7-E-K9 C819G-4G-ST-K9 C819HGW-S-A-K9
C819HGW+7-N-K9 C819G-4G-NA-K9 C819HG-B-K9
C819HG-4G-G-K9 C819G-B-K9
C819G-4G-G-K9
C819GW-LTE-MNA-AK9
C819GW-LTE-GA-EK9
C819G-LTE-LA-K9
C819G-4G-GA-K9
C819G-LTE-MNA-K9
C819HG-LTE-MNA-K9
C819GW-LTE-LA-CK9
C819GW-LTE-LA-QK9
C819GW-LTE-LA-NK9
1-36
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Table 1-13 lists the Cisco 3G antennas that are supported for use on Cisco 819 ISRs.
.
Table 1-13 Supported Cisco 3G Antennas
Cisco Part Number Antenna Type
Maximum Gain and
Frequency Range Description
3G-ANTM1919D Dipole
omnidirectional
0 dBi
(806–960 MHz)
0 dBi
(1710–2170 MHz)
This is the default antenna with dual faceplate mount.
Multiband faceplate-mounted dipole antenna. For more
information, see Cisco Multiband Swivel Mount Dipole
Antenna (3G-ANTM1919D).
3G-ANTM1916-CM High-gain
ceiling-mount
omnidirectional
1.5 dBi
(806–960 MHz)
2.5 dBi
(1710–2170 MHz)
Multiband ceiling-mounted omnidirectional antenna.
For more information, see Cisco Multiband
Omnidirectional Ceiling Mount Antenna
(3G-ANTM1916-CM).
3G-AE015-R
(Antenna Extension)
Extension base 0.8–6.0 GHz This antenna extension is a base with a 15-foot cable
included for use with a dipole omnidirectional antenna.
For more information, see Cisco Single-Port Antenna
Stand for Multiband TNC Male-Terminated Portable
Antenna (3G-AE015-R).
3G-ANTM-OUT-OM Outdoor
Omnidirectional
+2 dBi
800/900 MHz
+4 dBi
1800/1900/2100
MHz
This is an outdoor low-profile omindirectional mast
antenna. For more information, see Cisco 3G
Omnidirectional Outdoor Antenna
(3G-ANTM-OUT-OM).
3G-ANTM-OUT-LP Low Profile Stick
Antenna
–1.5 dBi
850, 900 MHz
–2.5 dBi
1800, 1900, 2100
MHz
This is an omindirectional stick antenna. For more
information, see Cisco 3G Low Profile Outdoor Antenna
(3G-ANTM-OUT-LP).
3G-ACC-OUT-LA
(Lightning Arrestor)
Lightning Arrestor 800–2200 MHz This is a quarter-wave lightning protector with
integrated high-pass filter. For more information, see
Cisco 3G Lightning Arrestor (3G-ACC-OUT-LA).
1-37
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Table 1-14 lists the supported Cisco WiFi antenna for Cisco 819HGW and Cisco 819HWD ISRs.
Table 1-14 Supported Cisco WiFi Antenna
Antenna
Frequency
band(s)
Mounting
Mechanical IP Rating
Peak Gain
2.4 GHz (dBi)
Peak Gain
5 GHz (dBi) Description
AIR-ANTM2050D-R 2.4–2.5 GHz
4.9–5.9 GHz
Faceplate
Dipole
IP 41 1.4 4.5 This is the default antenna. For
more information, see Cisco
Multiband Swivel-Mount
Dipole Antenna
(AIR-ANTM2050D-R).
AIR-ANT2430V-R 2.4 GHz Ceiling IP 41 3 For more information, see
Cisco Aironet 3-dBi
Omnidirectional Antenna
(AIR-ANT2430V-R).
AIR-ANT5140V-R 5 GHz Ceiling IP 41 4 For more information, see
Cisco Aironet 4-dBi
Omnidirectional Antenna
(AIR-ANT5140V-R).
AIR-ANT2440NV-R 2.4 GHz Multi-mount
(Wall/Ceiling
/Mast)
IP 54 4 For more information, see
Cisco Aironet 2.4-GHz MIMO
Wall-Mounted
Omnidirectional Antenna
(AIR-ANT2440NV-R).
AIR-ANT5140NV-R 5 GHz Multi-mount
(Wall/Ceiling
/Mast)
IP 54 4 For more information, see
Cisco Aironet 5-GHz MIMO
Wall Mount Omnidirectional
Antenna
(AIR-ANT5140NV-R).
1-38
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Table 1-15 lists the Cisco 4G LTE antennas that are supported for use on Cisco 819 ISRs.
Table 1-15 Supported 4G LTE Antennas
Cisco Part Number Description
Maximum Gain and
Frequency Ranges Description
4G-LTE-ANTM-D Indoor 4G dipole
omnidirectional antenna
2 dBi
698 to 806 MHz
824 to 894 MHz
925 to 960 MHz
1710 to 1885 MHz
1920 to 1980 MHz
2110 to 2170 MHz
2500 to 2690 MHz
Multiband dipole antenna. For more
information, see Cisco 4G/3G
Omnidirectional Dipole Antenna
(4G-LTE-ANTM-D).
4G-ANTM-OM-CM Indoor ceiling-mount
omnidirectional antenna
698 to 2690 MHz Multiband omnidirectional
ceiling-mount antenna. For more
information, see Cisco 4G Indoor
Ceiling-Mount Omnidirectional
Antenna (4G-ANTM-OM-CM).
ANT-4G-OMNI-OUT-N Multiband outdoor
omnidirectional stick
antenna
1.5 dBi
698 to 960 MHz
3.5 dBi
1710 to 2710 MHz
2300 to 2700 MHz
Multiband outdoor omnidirectional
stick antenna. For more information,
see Cisco Outdoor Omnidirectional
Antenna for 2G/3G/4G Cellular
(ANT-4G-OMNI-OUT-N).
ANT-4G-SR-OUT-TNC Multiband outdoor
omnidirectional saucer
antenna
1.5 dBi (peak gain with
10-foot cable) or 0.8 dBi
(peak gain with 15-foot
cable)
698 to 960 MHz
3.7 dBi (peak gain with
10-foot cable) or 0.2 dBi
(peak gain with 15-foot
cable)
1710 to 2700 MHz
Low-profile outdoor saucer antenna.
For more information, see Cisco
Integrated 4G Low-Profile Outdoor
Saucer Antenna
(ANT-4G-SR-OUT-TNC).
CGR-LA-NF-NF Lighning Arrestor 800 to 2200 MHz 4G lightning arrestor kit for use on
Cisco 4G wireless devices. For more
information, see Lightning Arrestor for
the Cisco 1240 Connected Grid Router.
4G-ACC-OUT-LA Lightning Arrestor 800 to 2200 MHz 4G lightning arrestor kit for use on
Cisco 4G wireless devices. For more
information, see Cisco 4G Lightning
Arrestor (4G-ACC-OUT-LA).
1-39
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Table 1-16 to Table 1-18 list the extension cables for use with 3G, WiFi, and 4G LTE antennas. The
tables include the insertion loss information for the ultra-low-loss (ULL) LMR 400 extension cables.
Table 1-16 Cisco Extension Cables for Use with 3G Antennas
Cisco Product Number Cable Length Insertion Loss Frequency (MHz)
3G-CAB-ULL-20 20 ft (6 m) 1.50 dB max 2100
3G-CAB-ULL-50 50 ft (15 m) 3.50 dB max 2100
3G-CAB-LMR240-25 25 ft (7.5 m) 3.50 dB max 2200
3G-CAB-LMR240-50 50 ft (15 m) 6.90 dB max 2200
3G-CAB-LMR240-75 75 ft (23 m) 10.5 dB max 2200
Table 1-17 Cisco Extension Cables for Use with WiFi Antennas
Cisco Product Number Cable Length Insertion Loss Frequency (MHz)
AIR-CAB005LL-R 5 ft (1.524 m)
(one RP-TNC plug, one
RP-TNC jack)
0.5 dB
0.8 dB
2400
5800
AIR-CAB020LL-R 20 ft (6 m)
(one RP-TNC plug, one
RP-TNC jack)
1.3 dB
2.5 dB
2400
5800
AIR-CAB050LL-R 50 ft (15.24 m)
(one RP-TNC plug, one
RP-TNC jack)
3.4 dB
5.75 dB
2400
5800
Table 1-18 Cisco Extension Cables for Use with 4G LTE Antennas
Cisco Product Number Cable Length
Maximum Insertion
Loss Frequency (MHz) Color Plenum Rated?
1
4G-AE010-R 10 ft (3 m) 1.4 dB at 700 MHz
2.0 dB at 1.9 GHz
2.1 dB at 2.1 GHz
2.3 dB at 2.5 GHz
700 to 2600 MHz Black No
4G-AE015-R 15 ft (4.6 m) 2.3 dB at 700 MHz
3.3 dB at 1.9 GHz
3.7 dB at 2.1 GHz
4.0 dB at 2.5 GHz
700 to 2600 MHz Black No
4G-CAB-LMR240-25 25 ft (7.6 m) 2.1 dB at 700 MHz
4.0 dB at 2.6 GHz
700 to 1000 MHz
1700 to 2600 MHz
Black Yes
1-40
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Serial Port
The Cisco standard High Speed Smart Serial 12-in-1 connector allows the highest flexibility of
connections to various DTE/DCE devices. The 12-in-1 serial interface pins connect to the FPGA. The
FPGA configures the pin directions based on the cable type used. Figure 1-10 shows the magnified view
of the 12-in-1 serial port. For more information, see About Serial Connections.
4G-CAB-LMR240-50 50 ft (15 m) 4.1 dB at 700 MHz
7.4 dB at 2.6 GHz
700 to 1000 MHz
1700 to 2600 MHz
Black Yes
4G-CAB-LMR240-75 75 ft (23 m) 6.1 dB at 700 MHz
11.0 dB at 2.6 GHz
700 to 1000 MHz
1700 to 2600 MHz
Black Yes
4G-CAB-LMR240-25N 25 ft (7.6 m) 2.1 dB at 700 MHz
4.0 dB at 2600 MHz
700 to 1000 MHz
1700 to 2600 MHz
Black No
4G-CAB-ULL-20 20 ft (6 m) 1.8 dB 700 to 2600 MHz Black Yes
4G-CAB-ULL-50 50 ft (15 m) 4.2 dB 700 to 2600 MHz Black Yes
CAB-L400-20-TNC-N 20 ft (6 m) 1.75 dB 700 to 2600 MHz Black No
CAB-L400-50-TNC-N 50 ft (15 m) 4.0 dB 700 to 2600 MHz Black No
CAB-L400-20-N-N 20 ft (6 m) 2.75 dB 700 to 2600 MHz Black No
1. Cable can be routed within building plenum spaces.
Table 1-18 Cisco Extension Cables for Use with 4G LTE Antennas (continued)
Cisco Product Number Cable Length
Maximum Insertion
Loss Frequency (MHz) Color Plenum Rated?
1
1-41
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 810 Series
Figure 1-10 12-in-1 Serial Port
Power Supply
All SKUs require a 5 VDC power source. Cisco 819HG and Cisco 819G ISRs have a self-locking Molex
mini-fit connector. Cisco 819HGW and Cisco 819HWD ISRs use a 5.5 mm barrel-type connector with
separate locking clip. An external AC power adapter is supported by default. The optional external power
adapters are available to support a variety of DC power sources, suitable for fixed, vehicle, or railway
installations. The 5 VDC power input of the router is protected from over-voltage up to 20 VDC. The
router will not power up if excessive voltage (for example, a 12 VDC adapter) is connected.
AC Power Adapter
The default configuration includes an external AC adapter that supplies up to 20 W of power. The AC
power connection is a two-pin IEC 320 C8 receptacle. A mating AC power cord is supplied. The AC
adapter does not provide chassis grounding to the router. A 1.3-meter long output cable connects to the
router.
DC Power Adapters
The optional external DC power adapters are available for 12 VDC and 24 VDC nominal vehicle power.
12 VDC vehicle adapter has a 10 VDC to 36 VDC operating range
24 VDC vehicle adapter has an 18 VDC to 75 VDC operating range
48 VDC vehicle adapter has an 20 VDC to 60 VDC operating range
344749
1-42
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
The vehicle power adapters may be used for fixed or mobile installations. They do not provide electrical
isolation; the input negative is connected to the output negative (chassis ground). Input cable is 350
millimeter long with stripped and tinned bare wire connections. The input positive connection is a white
wire and the input negative is a black wire.
Railway Power Adapters
The optional external power adapters meeting Railway Standards are available from a third-party
supplier, Martek Power. Contact Martek Power directly to order and for detailed specifications. The use
of Martek Power adapters listed in the “Supported Power Adapters” section on page A-9 will maintain
Cisco warranty and support of the router; the power adapter itself is covered by Martek warranty. Input
connection to the railway adapters is by a 350 millimeter long wire with stripped and tinned bare wire
connection. A 1.3-meter long output cable connects to the router.
Accessories
Table 1-19 lists the accessories available for the Cisco 819 ISRs. For a complete list of SKUs that support
these accessories, see the “Platform Features for Cisco 819 ISRs” section on page 1-27.
Cisco 860, 880, 890 Series
This section provides an overview of the features available for the Cisco 860 series, Cisco 880 series,
and Cisco 890 series Integrated Services Routers (ISRs), and contains the following sections:
General Description, page 1-43
Cisco 860 Series ISRs, page 1-43
Cisco 860VAE Series ISRs, page 1-45
Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 ISRs,
page 1-50
Cisco 880 Series ISRs, page 1-53
Cisco C881, C886, and C887 Series ISRs, page 1-66
Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers, page 1-76
Cisco 890 Series Integrated Service Routers, page 1-114
Cisco C891 Series ISRs, page 1-127
Hardware Features, page 1-132
Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap
that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series.
Table 1-19 Cisco 819 ISR Accessories
Cisco Part Number Accessory
69-2453-01 Power cord retention lock
69-2454-01 Power switch lock cover
1-43
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Note Some illustrations in this document show a wireless router. Both wireless and nonwireless models are
available in the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs. Port and feature locations
are similar for both wireless and nonwireless routers.
Note Throughout this document the term VDSL refers to support for VDSL2 (ITU G.993.2) and ADSL refers
to support for ADSL, ADSL2, & ADSL2+ (ITU G.992.1, G.992.3, & G.992.5).
General Description
The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs provide data, voice, Wi-Fi
CERTIFIED™ wireless access point (AP), integrated Virtual Private Network (VPN), and backup
capabilities to corporate teleworkers and to remote and small offices with fewer than 20 users. These
routers are capable of bridging and multiprotocol routing between LAN and WAN ports. The routers
provide advanced features, such as high speed DSL (G.SHDSL, ADSL, or VDSL), 802.11n, quality of
service (QoS), firewall, antivirus protection, and Secure Socket Layer (SSL). The Cisco 860VAE, 886VA
and 887VA series routers have the additional capability of DSL Multi-mode (VDSL/ADSL).
The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs have a desktop form factor with
built-in wall-mount features. The Cisco 890 series ISRs also have optional rack-mount features. These
ISRs are powered by an external power supply adapter. The various models differ in the WAN interface
and features that they support.
Cisco 860 Series ISRs
The Cisco 860 series ISRs are fixed-configuration data routers that support the following features:
An integrated 4-port 10/100 Ethernet switch for connecting to the LAN
A10/100 Fast Ethernet (FE) port for connecting to the WAN.
Optional, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP
1-44
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-7 shows the front panel details of the Cisco 860 wireless router.
Figure 1-11 Front Panel of the Cisco 860 Series Wireless ISR
Figure 1-12 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do
not have antennas on the back panel. However, the feature locations are similar for all Cisco 860 series
routers.
Figure 1-12 Back Panel of the Cisco 861W ISR
1 LEDs
231969
1
1 Primary WAN port—10/100 5 Reset button
2 Antenna—captive omnidirectional dipole
WLAN antenna (wireless models only)
6 Power connector
3 4-port 10/100 Ethernet switch 7 Earth ground connection
4 Serial port—console or auxiliary 8 Kensington security slot
232181
31 4 6 7 852
WAN
FE 4
Cisco 861W
1-45
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco 860VAE Series ISRs
The Cisco 860VAE series ISRs are fixed-configuration data routers. This section describes the features
of the products in this series.
Interfaces
Table 1-20 describes the interfaces of the Cisco 860VAE series routers.
Note The Cisco 866VAE, 867VAE, 866VAE-K9, and 867VAE-K9 routers each have two WAN ports. Only one
of the two ports can be active at any given time.
Table 1-21 describes the interfaces of the C860VAE series routers.
Table 1-20 Interfaces of the Cisco 860VAE Series ISRs
Interfaces
Model
Cisco
866VAE
Cisco
867VAE
Cisco
866VAE-K9
Cisco
867VAE-K9
4 FE
1
switch ports
1. FE = Fast Ethernet
xx x x
1 GE
2
switch port
2. GE = Gigabit Ethernet
—— x x
1 GE WAN port x x x x
1 VDSL/ADSL over POTS port x x
1 VDSL/ADSL over ISDN port x x
Table 1-21 Interfaces of the C860VAE Series ISRs
Interfaces
Model
C867VAE C866VAE-K9 C867VAE-K9
3 FE
1
switch ports
1. FE = Fast Ethernet
xx x
2 GE
2
switch port
2. GE = Gigabit Ethernet
xx x
1 GE WAN port x x x
1 VDSL/ADSL over POTS port x x
1 VDSL/ADSL over ISDN port x
1-46
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
IOS Images
Table 1-22 describes the IOS images included in Cisco 860VAE series routers.
Table 1-23 describes the IOS images included in C860VAE series routers.
Figure 1-13 shows the front panel details of the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and
Cisco 867VAE-K9 integrated services routers (ISRs).
Figure 1-13 Front Panel of the Cisco 860VAE series ISR
Table 1-22 IOS Images of the Cisco 860VAE Series ISRs
IOS Image
Model
Cisco
866VAE
Cisco
867VAE
Cisco
866VAE-K9
Cisco
867VAE-K9
c860vae-ipbasek9-mz x x
c860vae-advsecurityk9-mz x x
c860vae-advsecurityk9_npe-mz x x
Table 1-23 IOS Images of the C860VAE Series ISRs
IOS Image
Model
C867VAE C866VAE-K9 C867VAE-K9
c860vae-ipbasek9-mz x
c860vae-advsecurityk9-mz — x x
c860vae-advsecurityk9_npe-mz — x x
1 LEDs
246199
Cisco 860 Series
1
1-47
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-14 shows the front panel details of the C867VAE, C866VAE-K9, and C867VAE-K9 integrated
services routers (ISRs).
Figure 1-14 Front Panel of the C860VAE series ISR
Figure 1-15 shows the back panel details of the Cisco 866VAE ISR.
Figure 1-15 Back Panel of the Cisco 866VAE ISR
1 LEDs
246199
Cisco 860 Series
1
1 xDSL port
1
1. Using RJ-11.
6 On/Off switch
2 GE WAN interface 7 Power connector
3 Ethernet LAN FE interfaces (FE0 through
FE3 interfaces)
8 Reset button
4 USB port 9 Kensington security slot
5 Serial port—console or auxiliary
246200
CONSOLE
AUX
FE 2 FE 1 FE 0FE 3OVER ISDN
LAN
WAN
GE0
VDSL/ADSL
12V 2.5A
RESET
Cisco 866VAE
1 2 3 4 7 8 95 6
1-48
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-16 shows the back panel details of the C867VAE ISR.
Figure 1-16 Back Panel of the C867VAE ISR
Figure 1-17 shows the back panel details of the Cisco 867VAE-K9.
Figure 1-17 Back Panel of the Cisco 867VAE-K9 ISR
1 xDSL port
1
1. Using RJ-11.
6 On/Off switch
2 GE WAN interface 7 Power connector
3 Ethernet LAN GE and FE interfaces (GE0,
GE1 interfaces and FE0 through FE2
interfaces)
8 Reset button
4 USB port 9 Kensington security slot
5 Serial port—console or auxiliary
CONSOLE
AUX
OVER POTS
WAN LAN
GE2 GE1 GE0 FE2 FE1 FE0
VDSL/ADSL
12V 2.5A
RESET
Cisco 867VAE
1 2 3 4 7 8 95 6
385262
1 xDSL port 6 On/Off switch
2 GE WAN interface 7 Power connector
3 Ethernet LAN GE and FE interfaces (GE0
interface and FE0 through FE3 interfaces)
8 Reset button
4 USB port 9 Kensington security slot
5 Serial port—console or auxiliary
284558
CONSOLE
AUX
OVER POTS
WAN LAN
GE1 GE0 FE3 FE2 FE1 FE0
VDSL/ADSL
12V 2.5A
RESET
Cisco 867VAE-K9
1 2 3 4 7 8 95 6
1-49
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-18 shows the back panel details of the C866VAE-K9.
Figure 1-18 Back Panel of the C866VAE-K9 ISR
Figure 1-19 shows the back panel details of the C867VAE-K9.
Figure 1-19 Back Panel of the C867VAE-K9 ISR
1 xDSL port 6 On/Off switch
2 GE WAN interface 7 Power connector
3 Ethernet LAN GE and FE interfaces (GE0,
GE1 interfaces and FE0 through FE2
interfaces)
8 Reset button
4 USB port 9 Kensington security slot
5 Serial port—console or auxiliary
CONSOLE
AUX
OVER ISDN
WAN LAN
GE2 GE1 GE0 FE2 FE1 FE0
VDSL/ADSL
12V 2.5A
RESET
Cisco 866VAE-K9
1 2 3 4 7 8 95 6
385263
1 xDSL port 6 On/Off switch
2 GE WAN interface 7 Power connector
3 Ethernet LAN GE and FE interfaces (GE0,
GE1 interfaces and FE0 through FE2
interfaces)
8 Reset button
4 USB port 9 Kensington security slot
5 Serial port—console or auxiliary
CONSOLE
AUX
OVER POTS
WAN LAN
GE2 GE1 GE0 FE2 FE1 FE0
VDSL/ADSL
12V 2.5A
RESET
Cisco 867VAE-K9
1 2 3 4 7 8 95 6
385261
1-50
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and
Cisco 860VAE-POE-W-A-K9 ISRs
This section provides a hardware overview of the following Cisco 860VAE Series Integrated Services
Routers (ISRs):
C866VAE-W-E-K9
C867VAE-W-A-K9
C867VAE-W-E-K9
C867VAE-POE-W-A-K9
Model-Specific Features
Table 1-24 describes the features specific to each of these router models:
Common Features
The following key features are common to each of these router models:
Dual WAN interface (Gigabit Ethernet [GE] and dual-mode ADSL2+ /VDSL2)
2.4 GHz wireless LAN (WLAN) interface
Five Layer 2 LAN switches: two Gigabit Ethernet and three Fast Ethernet
One USB 2.0 port in high-speed host mode
One RJ-45 console port (RS-232 interface)
Support for up to 512 MB DRAM using DDR in 16-bit mode
Support for 8 MB Serial Peripheral Interface Bus (SPI) flash memory for boot and 128 MB NAND
flash memory for storing IOS
Reset/Recovery switch
Silent convection cooling—no fan
External Interfaces
Figure 1-20 shows the back I/O panel of the Cisco 867VAE-POE-W-A-K9 series router.
Table 1-24 Model-Specific Router Features
Feature
C866VAE-W-E-
K9
C867VAE-W-A-
K9
C867VAE-W-E-
K9
C867VAE-POE-
W-A-K9
WAN interface and mode One GE port,
DSL over
ISDN,
Europe WiFi
One GE port,
DSL over
POTS,
America WiFi
One GE port,
DSL over
POTS,
Europe WiFi
One GE port,
DSL over
POTS,
America WiFi
Power-over-Ethernet (PoE)NoNoNoYes
1-51
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-20 Back I/O Panel
Table 1-25 describes the external interfaces included with these router models.
Note For the Cisco C867VAE-POE-W-A-K9, Power-over-Ethernet (PoE) is available using port FE0, with a
60-W power supply.
USB Interface
The USB 2.0 interface enables:
Transferring data using a USB flash token (USB memory stick) for system recovery and other tasks.
Cisco IOS software boot from USB.
Use only the following Cisco USB 2.0 flash tokens:
MEMUSB-128FT (128 MB)
MEMUSB-256FT (256 MB)
MEMUSB-1024FT (1 GB)
Note The USB 2.0 port cannot be used for connecting external devices or as a console for devices other than
those specified in the USB eToken Device and USB Flash Features Support Data Sheet, available at:
http://www.cisco.com/en/US/prod/collateral/modules/ps6247/product_data_sheet0900aecd80232473.h
tml
VDSL/ADSL
WAN
GE2
LAN
GE1OVER POTS
CONSOLE
12V
RESET
2.5A
AUX
GE0 FE2 FE1
Cisco 867VAE-POE-W-A-K9
FE0(POE)
360426
Table 1-25 External Interfaces
Interface Connector Quantity Port
Port
Label
FE LAN port RJ-45 3 FE LAN PORT 0 FE0
1
1. Provides Power-over-Ethernet (PoE) for the Cisco C867VAE-POE-W-A-K9.
FE LAN PORT 1 FE1
FE LAN PORT 2 FE2
GE LAN port RJ-45 2 GE LAN PORT 0 GE0
GE LAN PORT 1 GE1
GE WAN port (10/100/1000 Base-T) RJ-45 1 GE WAN PORT GE2
ADSL2+/VDSL2 WAN port RJ-11 1
Host USB port USB 2.0 1
Console port RJ-45 1
1-52
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
LED Indicators
These router models include LED indicators on the back panel for each LAN port, and additional LED
indicators on the front panel of the unit.
LED Indicators for LAN Ports
On the back panel of the unit, each LAN port includes an LED indicator. Table 1-26 describes the LED
indicators.
LED Indicators on Front Panel
The front panel includes several LED indicators. Figure 1-21 shows the location of the LED indicators.
Figure 1-21 Front Panel LED Indicators
Table 1-26 Back Panel LED Indicators for LAN Ports
Port LED Color Description
FE Ports
FE LAN 0 Green Off—No link.
Faster flashing indicates heavier traffic.
FE LAN 1 Green Off—No link.
Faster flashing indicates heavier traffic.
FE LAN 2 Green Off—No link.
Faster flashing indicates heavier traffic.
GE Ports
GE LAN 0 Green Off—No link.
Faster flashing indicates heavier traffic.
GE LAN 1 Green Off—No link.
Faster flashing indicates heavier traffic.
1 LED indicators
346497
Cisco 860 Series
WLAN
1
1-53
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-27 describes the LED indicators.
Cisco 880 Series ISRs
The Cisco 880 series ISRs have data and voice capabilities. They have the following features:
Table 1-27 Front Panel LED Indicators
LED LED Color LED Activity Description
Left Side
DSL ACT Green Flashing DSL WAN activity. Faster flashing indicates heavier
traffic.
Off Device is powered off.
or
No DSL WAN activity.
DSL LINK Green Solid DSL WAN mode is selected and DSL training is complete.
Flashing DSL WAN mode is selected but DSL LinkUp state is
incomplete, such as in-training (slow initially, fast when
almost connected).
Off Device is powered off.
or
GE WAN mode is selected.
GE ACT Green Flashing GE WAN activity (traffic in either direction). Faster
flashing indicates heavier traffic.
Off Device is powered off.
or
No GE WAN activity.
or
No link.
GE MODE Green Solid GE WAN mode is selected.
Off Device is powered off.
or
DSL WAN mode is selected.
Right Side
WLAN Green Solid WLAN enabled.
Flashing Indicates WLAN activity (traffic in either direction).
Off Device is powered off.
or
WLAN is disabled.
Power Green Solid On—The device is powered on.
Off Device is powered off.
1-54
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Integrated 4-port 10/100 Ethernet switch for connecting to the LAN
10/100 FE, VDSLoPOTS, ADSL over POTS, ADSL over ISDN, DSL Multi-mode
(VDSL/ADSLoPOTS, VDSL/ADSLoISDN Cisco VA models only), or G.SHDSL port for
connecting to the WAN
Optional embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP
Optional 2-port Power over Ethernet (PoE)
Note The Cisco 880 series ISRs can include an optional PoE module that provides power to
802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not
configured with the factory order, you must order and install it to enable the PoE function.
DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB
system memory
The following features are located on the front panel:
USB 1.1 port
Express card slot for third-generation (3G) cellular data WAN connectivity, available only on the
Cisco 880G models
This section contains the following topics:
Cisco 880 Series Data Routers, page 1-54
Cisco 880 Series Voice and Data Routers, page 1-57
Cisco 880 Series with Embedded WLAN Antennas, page 1-63
C881G-B/S/V-K9 ISRs, page 1-65
C881GW-S/V-A-K9 ISRs, page 1-65
C881G-U-K9 ISRs, page 1-66
HSPA+ Versions of the Fixed-Platform ISRs, page 1-66
Cisco 880 Series Data Routers
The Cisco 880 series data routers provide integrated VPN, embedded Wi-Fi CERTIFIED™,
802.11b/g/n-compliant wireless AP, 3G, and backup capabilities. Figure 1-22 through Figure 1-25 show
the features available on Cisco 880 series data routers. Some of the features shown may not be available
on your router.
Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, VDSL/ADSL
over ISDN, VDSL/ADSL over POTS, or 10/100 FE. See the Cisco 880 Series Integrated Services
Routers data sheet for the WAN interface that is supported on your router.
Figure 1-22 shows the front panel details of the Cisco 880 wireless data router. The USB port and the
3G card slot are located on the front panel.
1-55
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-22 Front Panel of the Cisco 880 Series Wireless Data Router
Figure 1-23 shows the back panel details of the Cisco 886VA data router.
Figure 1-23 Back Panel of the Cisco 886VA Router
1 LEDs 3 USB port
2 3G express card slot—Supports third-party
1
3G card (Cisco 880G models only)
1. See the Cisco 880 Series Integrated Services Routers data sheet for supported vendors.
231950
1 2 3
254090
1 3 4 5 7 8 962
1 Data BRI
1
0 6 Reset button
2 Primary WAN port—VDSL/ADSL over
ISDN
7 Power connector
3 4-port 10/100 Ethernet switch
2
8 Earth ground connection
4 Serial port—console or auxiliary 9 Kensington security slot
5 PoE power connector—optional
1. BRI = Basic rate interface.
2. Ports 0 and 1 provide PoE with the optional PoE module installed.
The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN port may
occur if a non-RJ-45 connector is inserted.
1-56
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-24 shows the back panel details of the Cisco 887VA and 886VA-M data router.
Figure 1-24 Back Panel of the Cisco 887VA and 887VA-M Router
Figure 1-25 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have
antennas on the back panel. However, the feature locations are similar across all Cisco 880 series data
routers.
Figure 1-25 Back Panel of the Cisco 888W Data Router
254139
2 3 4 6 7 851
1 Primary WAN port—VDSL/ADSL over
POTS
1
5 Reset button
2 4-port 10/100 Ethernet switch
2
6 Power connector
3 Serial port—console or auxiliary 7 Earth ground connection
4 PoE power connector—optional 8 Kensington security slot
1. 887VA-M has Annex M support.
2. Ports 0 and 1 provide PoE with the optional PoE module installed.
For the Cisco 887VA, the primary WAN port is designed for an RJ-11 connector only. Damage to the
primary WAN port may occur if a non-RJ-11 connector is inserted.
231951
1 4 5 6 8 9 1072 3
1-57
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco 880 Series Voice and Data Routers
The Cisco 880 series voice and data routers provide both voice and data ports. The voice ports managed
voice services that interface with Foreign Exchange Station (FXS), Foreign Exchange Office (FXO), or
BRI connections.
Cisco 881 SRST and Cisco 888 SRST
Figure 1-26, Figure 1-27, and Figure 1-28 show the features available on the Cisco 881 SRST and
Cisco 888 SRST routers. The features available vary, depending on the router model. Some features may
not be available on your router.
Depending on the router model, the primary WAN port can be either G.SHDSL or 10/100 FE. See the
Cisco 880 Series Integrated Services Routers data sheet for the WAN interface and voice ports that are
supported on your router.
1 ISDN port—not available on 3G models 6 PoE power connector for optional PoE
module
1
2 Primary WAN port
2
—G.SHDSL,
VDSLoPOTS, ADSLoPOTS, ADSLoISDN,
or 10/100 FE
7 Reset button
3 Antenna—captive omnidirectional dipole
WLAN antenna (wireless models only)
8 Power connector
4 4-port 10/100 Ethernet switch 9 Earth ground connection
5 Serial port—console or auxiliary 10 Kensington security slot
1. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install it to enable the
PoE function.
2. Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, or 10/100 FE. The VDSLoPOTS
port is in the same location as the G.SHDSL port. The 10/100 FE WAN port is located at the bottom left corner. See
Figure 1-12 for the location of the 10/100 FE WAN port.
1-58
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-26 shows the front panel details of the Cisco 881 SRST and Cisco 888 SRST wireless voice
router.
Figure 1-26 Front Panel of the Cisco 881 SRST and Cisco 888 SRST Wireless Voice Router
1 LEDs 2 USB port
270495
1 2
1-59
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-27 shows the back panel details of the Cisco 881SRST-W voice router.
Figure 1-27 Back Panel of the Cisco C881SRST-W Voice Router
1 Primary WAN port
1
—10/100 FE
1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.
6 Antenna—captive wireless omnidirectional
dipole WLAN antenna (wireless models only)
2 Voice ports—four FXS
2
/DID
3
ports, one
FXO
4
port with TBP
5
power failover
2. FXS = Foreign Exchange Station.
3. DID = Direct Inward Dialing.
4. FXO = Foreign Exchange Office.
5. TBP = trunk bypass.
7 Reset button
3 4-port 10/100 Ethernet switch
6
6. Ports 0 and 1 provide PoE with the optional PoE module installed.
8 Power connector
4 Serial port—console or auxiliary 9 Earth ground connection
5 PoE power connector for optional PoE
module
7
7. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install the Field
Replaceable Unit (FRU) to enable the PoE function. For this you either need the FRU “800-IL-PM=2” or “800G2-POE-2”.
If your device has a separate PoE inlet, use the 800-IL-PM=2, if it has one combined inlet (a description saying “POE
OPTION REQUIRES 5A POWER ADAPTOR”), then use the 800G2-POE-2.
10 Kensington security slot
241904
31 4 7 98 1022 56
1-60
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-28 shows the back panel details of the Cisco 888SRST-W voice router.
Figure 1-28 Back Panel of the Cisco C888SRST-W Voice Router
Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W
Figure 1-29, Figure 1-30, and Figure 1-31 show the features available on the Cisco 881-V and
Cisco 887VA-V routers. The features available vary, depending on the router model. Some features may
not be available on your router.
The Cisco 881-V and Cisco 887VA-V voice and data series gives you the flexibility to use either FXS
or BRI voice ports. However, the number of concurrent calls that can be supported by the router is limited
by the codec complexity setting on the router. Table 1-28 lists the maximum number of calls that is
supported when the codec complexity command is configured for Flexible, Medium or High complexity.
1 Primary WAN port
1
—G.SHDSL
1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.
6 Antenna—captive wireless omnidirectional
dipole WLAN antenna (wireless models only)
2 Voice ports—four FXS/DIDports and one
voice BRI port
7 Reset button
3 4-port 10/100 Ethernet switch
2
2. Ports 0 and 1 provide PoE with the optional PoE module installed.
8 Power connector
4 Serial port—console or auxiliary 9 Earth ground connection
5 PoE power connector for optional PoE
module
3
3. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install the Field
Replaceable Unit (FRU) to enable the PoE function. For this you either need the FRU “800-IL-PM=2” or “800G2-POE-2”.
If your device has a separate PoE inlet, use the 800-IL-PM=2, if it has one combined inlet (a description saying “POE
OPTION REQUIRES 5A POWER ADAPTOR”), then use the 800G2-POE-2.
The primary WAN port on all 888E models is designed for an RJ-45 connector only. Damage to the
primary WAN port may occur if a non-RJ-45 connector is inserted.
10 Kensington security slot
241905
32 2 4 7 9 1086 51
1-61
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Note Configuring the codec complexity setting to support secure calls uses DSP resources, but does not affect
the maximum number of supported calls.
Figure 1-29 shows the front panel details of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W.
Figure 1-29 Front Panel of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W Routers
Table 1-28 Maximum Number of Supported Calls
Flexible Complexity Medium Complexity High Complexity
C881-V986
C887VA-V886
C887VA-V-W 8 8 6
246861
1 2
1 LEDs 2 USB port
1-62
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-30 shows the back panel for the Cisco 887VA-V-W router. The Cisco 887VA-V (non-wireless)
router does not have the antennas on the back panel.
Figure 1-30 Back Panel of the Cisco 887 VA-V Router
Figure 1-31 shows the back panel for the Cisco 881-V router.
Figure 1-31 Back Panel of the Cisco 881-V Router
246864
overPOTS
VDSL/ADSL
C887VA-W VOICE
3
4
56
1 4 5 6 8 9 107
32
11
1 Data BRI 7 Reset Button
2 Voice BRI 8 Power connector
3 Voice ports—four FXS/DID ports 9 Earth ground connection
4 Fast Ethernet LAN—four ports 10 Kensington security slot
5 Console Port 11 Primary WAN port—VDSL/ADSL over
POTS
6 PoE power connector (optional)
246866
C881 VOICE
3
4
56
7
1 4 5 6 8 9 10732
1-63
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco 880 Series with Embedded WLAN Antennas
Some Cisco 880W, 880WD, and 880-WD ISRs have three embedded WLAN antennas.
These ISRs are fixed-platform routers that:
Provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP, and
backup capabilities.
Use single-band (2.4 GHz) WLAN cards or dual-band (2.4 GHz and 5 GHz) WLAN cards.
Require a single external power supply: a 30-W power supply for non-POE-enabled routers or a
60-W power supply for POE-enabled routers.
Have a fixed 512 MB of system memory.
For information on configuring the Cisco 880 series ISRs, see Cisco 880 Series Integrated Services
Router Software Configuration Guide.
Cisco 887VA-WD
Figure 1-32 shows the front panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs. The
front panel has LEDs only. All the ports are in the back panel.
Figure 1-32 Front Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs
1 Fast Ethernet WAN port 6 PoE power connector (optional)
2 Voice BRI ports 7 Reset button
3 Voice ports—four FXS/DID ports and one
FXO port.
8 Power connector
4 Fast Ethernet LAN—four ports 9 Earth ground connection
5 Console Port 10 Kensington security slot
284983
OK
PPP
WLAN
POE
0
1
LINK 2.4GHz 5GHz
Cisco 800 Series
FE LAN
VPN
0123
xDSL
CD DATA
1-64
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-33 shows the back panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs.
Figure 1-33 Back Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs
C881WD
Figure 1-34 shows the front panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs. The front
panel has LEDs only. All the ports are in the back panel.
Figure 1-34 Front Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs
284988
Cisco 887VA-WD
AUX
CONSOLE
FE LAN
POE OPTION
REQUIRES 5A
POWER
ADAPTOR
3 210
RESET
12VDC 5A
0
O
overPOTS
89
1 2 3 4 5 6 7
284988
Cisco 887VA-WD
AUX
CONSOLE
FE LAN
POE OPTION
REQUIRES 5A
POWER
ADAPTOR
3 210
RESET
12VDC 5A
0
O
overPOTS
89
1 2 3 4 5 6 7
1 USB port 6 Power connector
2 4-port 10/100 Ethernet switch 7 Kensington security slot
3 Serial port—console or auxiliary 8 Power switch
4
Note No separate PoE power supply is
required for routers with embedded
WLAN antennas. For information on
system power supply requirements
when PoE is enabled, see the “Power
over Ethernet Module” section on
page 1-143.
9 VDSL/ADSL port
5 Reset button
284982
OK
PPP
FE4
WAN
WLAN
POE
0
1
LINK 2.4GHz 5GHz
Cisco 800 Series
FE LAN
VPN
0123
1-65
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-35 shows the back panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs.
Figure 1-35 Back Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs
C881G-B/S/V-K9 ISRs
The C881G-B-K9, C881G-S-K9, and C881G-V-K9 ISRs are members of the Cisco 880 series data
routers. These routers provide integrated Virtual Private Network (VPN), 802.11b/g/n-compliant
wireless Access Point (AP), 3G, and backup capabilities.
For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router
Software Configuration Guide.
C881GW-S/V-A-K9 ISRs
The C881GW-S-A-K9 and C881GW-V-A-K9 ISRs are members of the Cisco 880G series data routers.
These routers provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless
AP, 3G, and backup capabilities.
For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router
Software Configuration Guide.
284987
Cisco 881WD
AUX
CONSOLE
FE LAN
POE OPTION
REQUIRES 5A
POWER
ADAPTOR
3 210
RESET
12VDC 5A
0
O
FE WAN
4
9
21 3 4 5 6 7 8
1 Primary WAN port—10/100 FE 6 Reset button
2 USB port 7 Power connector
3 4-port 10/100 Ethernet switch 8 Kensington security slot
4 Serial port—console or auxiliary 9 Power switch
5
Note No separate PoE power supply is
required for routers with embedded
WLAN antennas. For information on
system power supply requirements
when PoE is enabled, see the “Power
over Ethernet Module” section on
page 1-143.
1-66
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
C881G-U-K9 ISRs
The C881G-U-K9 ISR is a member of the Cisco 880 series data routers. These routers provide integrated
Virtual Private Network (VPN), embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless
Access Point (AP), 3G, and backup capabilities.
For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router
Software Configuration Guide.
HSPA+ Versions of the Fixed-Platform ISRs
The C881G+7-K9, C886VAG+7-K9, C887VAG+7-K9, C887VAMG+7-K9, C888EG+7-K9,
C881GW+7-A-K9, C881GW+7-E-K9, C887VAGW+7-A-K9, and C887VAGW+7-E-K9 ISRs are
members of the Cisco 880G series data routers. These routers provide integrated VPN, embedded Wi-Fi
CERTIFIED™, 802.11b/g/n-compliant wireless AP, 3G, and backup capabilities.
For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router
Software Configuration Guide.
Cisco C881, C886, and C887 Series ISRs
Cisco C881, C886, and C887 Series ISRs offer broadband speed and simplified management to small
businesses, small enterprise branches, and teleworkers. The Cisco C881, C886, and C887 Series ISR
models have a lead-free, fanless chassis and are updated versions of the previous Cisco 881, 886, and
887 series (excluding 3G and wireless models).
Information provided in this section is applicable for the following models:
Cisco C881
Cisco C886VA, Cisco C886VAJ (Annex J)
Cisco C887VA, Cisco C887VAM (Annex M)
Table 1-29 provides information about important hardware specifications pertaining to Cisco C881,
C886, and C887 Series Routers.
Table 1-29 Hardware Specifications of Cisco C881, C886, and C887 Series
Routers
Hardware Description
Flash Memory 256 MB
Main Memory 1 GB DDR RAM; fixed and not extendable
USB port A USB 2.0-compliant port located at the back
panel
FAN Fanless chassis
PoE Two internal PoE ports
WAN
C881— FE
C886—VDSL/ADSL over ISDN with ISDN
back up
C887—VDSL/ADSL over POTS
1-67
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
For detailed hardware specifications, see the Cisco 880 Series hardware data sheet at:
http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78_459542_ps380_Products_
Data_Sheet.html
Cisco C881 Router
Figure 1-36 shows the front panel of the Cisco C881 Router.
Figure 1-36 Front Panel of the Cisco C881 Router
For detailed description about the LEDs on the Cisco C880 Series Routers, see the “LEDs” section on
page 1-30.
Console or auxiliary port RJ-45
LAN switch 4-port 10/100BASE-T
Hardware Description
CiscoCisco
800
Series
OKOK
POEOE
PPPPPP
FEFE4
WAN
0 1
VPN
0 1 2
3
FE
FE LAN
361124
1
1 LEDs
1-68
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-37 shows the back panel of the Cisco C881 Router.
Figure 1-37 Back Panel of the Cisco C881 Router
For information on installing the Cisco C880 Series Routers, see :
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
l880-860.html
Cisco C886VA Router
Figure 1-38 shows the front panel of the Cisco C886VA Router.
Figure 1-38 Front Panel of the Cisco C886VA Router
For detailed description about the LEDs on the Cisco C880 Series Routers, see the “LEDs” section on
page 1-30.
0
Cisco 881
FE LAN
3210
CONSOLE
AUX
FE WAN
4
12VDC 2 .5-5A
(POE)
RESET
361125
1 2 3 4 5 7 8 9
6
1 Primary WAN port—FE 6 Reset button
2 USB port 7 Power connector
3 4-port 10/100 Ethernet switch 8 Earth ground connection
4 Serial port—Console or auxiliary 9 Kensington security slot
5 On/Off switch
361126
CiscoCisco
800
Series
OKOK
POEOE
PPPPPP
FE FE LAN
VPN
0 1 2
3
0 1
CD
CD DATA
xDSL
xDSL
ISDNISDN
LINKLINK
B1B1
B2B2
1
1 LEDs
1-69
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-39 shows the back panel of the Cisco C886VA Router.
Figure 1-39 Back Panel of the Cisco C886VA Router
For information on installing Cisco C880 Series Routers, see:
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
l880-860.html
Cisco C886VAJ Router
Figure 1-40 shows the front panel of the Cisco C886VAJ Router.
Figure 1-40 Front Panel of the Cisco C886VAJ Router
For detailed description about LEDs on the Cisco 880 Series Router, see the “LEDs” section on
page 1-30.
361127
VDSL/ADSL
VDSL/ADSL
over ISDN
over ISDN
0
0
ISDN
ISDN
FE LAN
FE LAN
CONSOLE
CONSOLE
AUX
AUX
3 2 1 0
12VDC
2.
2.5
-5A
-5A
(POE)
(POE)
RESET
RESET
21 3 4 5 6 8 9 10
7
1 Primary WAN port—VDSL/ADSL over
ISDN
6 On/Off switch
2 USB port 7 Reset button
3 ISDN 8 Power connector
4 4-port 10/100 Ethernet switch 9 Earth ground connection
5 Serial port—Console or auxiliary 10 Kensington security slot
361128
CiscoCisco
800
Series
OKOK
POEOE
PPPPPP
FE FE LAN
VPN
0 1 2
3
0 1
CD
CD DATA
xDSL
xDSL
ISDNISDN
LINKLINK
B1B1
B2B2
1
1 LEDs
1-70
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-41 shows the back panel of the Cisco C886VAJ Router.
Figure 1-41 Back Panel of the Cisco C886VAJ Router
For information on installing Cisco C880 Series Routers, see:
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
l880-860.html
Cisco C887VA Router
Figure 1-42 shows the front panel of the Cisco C887VA Router.
Figure 1-42 Front Panel of the Cisco C887VA Router
For detailed description about the LEDs on Cisco C880 Series Router, see the “LEDs” section on
page 1-30.
361129
VDSL/ADSLVDSL/ADSL
over ISDNover ISDN
0
0
ISDN
ISDN
FE LANFE LAN
CONSOLECONSOLE
AUXAUX
3 2 1 0
12VDC 2.
2.5-5A-5A
(POE)(POE)
RESETRESET
21 3 4 5 6 8 9 10
7
1 Primary WAN port—VDSL/ADSL over
ISDN
6 On/Off switch
2 USB port 7 Reset button
3 ISDN 8 Power connector
4 4-port 10/100 Ethernet switch 9 Earth ground connection
5 Serial port—Console or auxiliary 10 Kensington security slot
361130
Cisco
Cisco
800
Series
OK
OK
P
OE
OE
PPP
PPP
FE
FE LAN
VPN
0
1 2
3
0 1
CD
CD DATA
xDSL
xDSL
1
1 LEDs
1-71
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-43 shows the back panel of the Cisco C887VA Router.
Figure 1-43 Back Panel of the Cisco C887VA Router
For information on installing Cisco C880 series routers, see the following link:
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
l880-860.html
Cisco C887VAM Router
Figure 1-44 shows the front panel of the Cisco C887VAM router:
Figure 1-44 Front Panel of the Cisco C887VAM Router
For detailed description about LEDs on Cisco C880 series router, see “LEDs” section on page 1-30.
361131
0
Cisco
Cisco
887
887VA
VDSL/ADSL
VDSL/ADSL
over POTS
over POTS
FE LAN
FE LAN
3 2 1 0
CONSOLE
CONSOLE
AUX
AUX
12VDC
2.
2.5
-5A
-5A
(POE)
(POE)
RESET
RESET
21 3 4 5 7 8 9
6
1 Primary WAN port—VDSL/ADSL over
POTS
6 Reset button
2 USB port 7 Power connector
3 4-port 10/100 Ethernet switch 8 Earth ground connection
4 Serial port—console or auxiliary 9 Kensington security slot
5 On/Off switch
361132
CiscoCisco
800
Series
OKOK
POEOE
PPPPPP
FE FE LA N
VPN
0
1 2
3
0 1
CD
CD DATA
xDSL
xDSL
1
1 LEDs
1-72
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-45 shows the back panel of the Cisco C887VAM router.
Figure 1-45 Back Panel of the Cisco C887VAM Router
For information on installing the Cisco C880 Series Routers, see:
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
l880-860.html
361133
0
CiscoCisco 887887VAMAM
VDSL/ADSLVDSL/ADSL
over POTSover POTS
FE LANFE LAN
3 2 1 0
CONSOLE
CONSOLE
AUXAUX
12VDC 2.2.5-5A-5A
(POE)(POE)
RESETRESET
21 3 4 5 7 8 9
6
1 Primary WAN port—VDSL/ADSL over
POTS
6 Reset button
2 USB port 7 Power connector
3 4-port 10/100 Ethernet switch 8 Earth ground connection
4 Serial port—Console or auxiliary 9 Kensington security slot
5 On/Off switch
1-73
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco C888 Integrated Services Router
The Cisco C888 Integrated Services Router (ISR) offers broadband speeds and simplified management
to small businesses, enterprise small branches, and teleworkers. The Cisco C888 ISR supports multi
mode G.SHDSL (EFM+ATM) WAN connectivity. The Cisco C888 ISR has a lead free, fanless chassis
and it is an updated version of the previous Cisco 888 (888 A and 888 EA) ISR models.
Table 1-30 provides information about important hardware specifications pertaining to the Cisco C888
ISR.
Table 1-30 Hardware Specifications for Cisco C888 ISR
Note If you change G.SHDSL mode from EFM to ATM or from ATM to EFM, you should reload the router.
Note EFM auto mode is supported only on the first pair. EFM manual mode can be supported on all the 4 pairs.
Note Cisco C888 ISR does not support Inverse Multiplexing over ATM (IMA) mode.
For detailed hardware specifications, see the Cisco 880 Series hardware data sheet at:
http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78_459542_ps380_Products_
Data_Sheet.html
Hardware Description
Flash Memory 256 MB
Main Memory 1-GB DDR RAM ; fixed, and not extendable
USB port A USB 2.0-compliant port located at the back
panel
FAN Fanless chassis.
PoE Two internal PoE ports
WAN 4-pair multimode G.SHDSL (EFM+ATM) with
ISDN backup.
Console or auxiliary port RJ-45
LAN switch 4-port 10/100BASE-T
1-74
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-46 shows the front panel of the Cisco C888 Router:
Figure 1-46 Front Panel of the Cisco C888 Router
For detailed description about the LEDs on the Cisco 880 Series Routers, see information available at:
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/1Overv
iew880-860.html#wp1147924
361134
CiscoCisco
800
Series
OKOK
POEOE
PPPPPP
FE FE LAN
VPN
0 1 2
3
0 1
CD
CD DATA
xDSL
xDSL
ISDNISDN
LINKLINK
B1B1
B2B2
EFMEFM
ATMATM
1
1 LEDs
1-75
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-47 shows the back panel of the Cisco C888 Router.
Figure 1-47 Back Panel of the Cisco C888 Router
For information on installing Cisco 800 Series Routers, see the information available at:
http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG/installin
g.html#pgfId-1098019
361135
0
FE LAN
FE LAN
3 2 1 0
CiscoCisco 888888
SHDSLSHDSL
RJ45 ONJ45 ONLY
ISDN
ISDN
0
CONSOLE
CONSOLE
AUXAUXAUXAUX
12VDC 2.2.5-5A-5A
(POE)(POE)
RESETRESET
2 31 4 5 6 8 9 10
7
1 Primary WAN port—G.SHDSL 6 On/Off switch
2 USB port 7 Reset button
3 ISDN 8 Power connector
4 4-port 10/100 Ethernet switch 9 Earth ground connection
5 Serial port—console or auxiliary 10 Kensington security slot
1-76
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers
Cisco C880 Series and Cisco C890 Series 4G LTE Integrated Services Routers (ISRs) extend 4G LTE
support to the existing Cisco 880 Series and Cisco 890 Series ISRs. The Cisco C880 Series and Cisco
C890 Series 4G LTE ISRs are based on the Sierra Wireless MC7304 modem and Cisco C880 Series and
Cisco C890 4G LTE Series ISRs can support higher data rates compared to 3G in both up link and down
link directions with 4G LTE support.
This section provides information about the following models:
Cisco C881G-4G ISR
Cisco C887VAG-4G ISR
Cisco C896VAG-LTE ISR
Cisco C897VAG-LTE ISR
Cisco C898EAG-LTE ISR
Cisco C899G-LTE ISR
Table 1-31 provides information about important hardware specifications pertaining to Cisco C880 4G
LTE Series ISRs.
Table 1-32 provides information about important hardware specifications pertaining to Cisco C890 4G
LTE Series ISRs.
Table 1-31 Hardware Specifications for Cisco C880 4G LTE Series ISRs
Hardware Description
Flash Memory 1GB
Main Memory 1-GB DDR RAM
USB port A USB 2.0-compliant port located at the back
panel
PoE Two PoE ports
WAN
C881G-4G— FE
C887VAG-4G—VDSL or ADSL over POTS
Console or auxiliary port RJ-45
LAN switch 4-port 10/100BASE-T
Table 1-32 Hardware Specifications for Cisco C890 4G LTE Series ISRs
Hardware Description
Flash Memory 1 GB
Main Memory 1-GB DRAM
USB port A USB 2.0-compliant port located at the back
panel.
PoE Four PoE ports
1-77
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
WAN C896VAG-LTE—VDSL or ADSL over
ISDN, GE
C897VAG-LTE—VDSL or ADSL over
POTS, GE
C898EAG-LTE—G.SHDSL over POTS, GE
C899G-LTE—GE, SFP
Console or auxiliary port RJ-45
LAN switch 8-port 10/100/1000 BASE-T
Table 1-32 Hardware Specifications for Cisco C890 4G LTE Series ISRs
Hardware Description
1-78
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-33 lists the different 4G LTE SKUs available for the Cisco 880 and Cisco 890 series ISRs.
1-79
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-33 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs
SKU ID Mode
Operating
Region Frequency Band Description
C881G-4G-GA-K9
LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
Global (Europe,
New Zealand,
and Australia)
LTE:
800 MHz (band 20)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
3G (UMTS, HSPA+, HSPA):
800 MHz (band 6)
850 MHz (band 5)
900 MHz (band 8)
1900 MHz (band 2)
2100 MHz (band 1)
2G (GSM, EDGE, GPRS):
850 MHz
900 MHz
1800 MHz
1900 MHz
Cisco 880 Series ISR
Multimode LTE
feature for global
wireless networks.
C881G-4G-GA-K9
comes with a Sierra
Wireless MC7304
modem.
C886VAG-LTE-GA-
K9
LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
Global (Europe,
New Zealand,
and Australia)
LTE:
800 MHz (band 20)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
3G (UMTS, HSPA+, HSPA):
800 MHz (band 6)
850 MHz (band 5)
900 MHz (band 8)
1900 MHz (band 2)
2100 MHz (band 1)
2G (GSM, EDGE, GPRS):
850 MHz
900 MHz
1800 MHz
1900 MHz
Cisco 880 series ISR
with Multimode LTE
feature for global
wireless networks.
C886VAG-LTE-GA-K
9 comes with a Sierra
Wireless MC7304
modem.
1-80
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
C887VAG-4G-GA-
K9
LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
Global (Europe,
New Zealand,
and Australia)
LTE:
800 MHz (band 20)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
3G (UMTS, HSPA+, HSPA):
800 MHz (band 6)
850 MHz (band 5)
900 MHz (band 8)
1900 MHz (band 2)
2100 MHz (band 1)
2G (GSM, EDGE, GPRS):
850 MHz
900 MHz
1800 MHz
1900 MHz
Cisco 880 series ISR
with Multimode LTE
feature for global
wireless networks.
C887VAG-4G-GA-K9
comes with a Sierra
Wireless MC7304
modem.
C896VAG-LTE-GA-
K9
LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
Global (Europe,
New Zealand,
and Australia)
LTE:
800 MHz (band 20)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
3G (UMTS, HSPA+, HSPA):
800 MHz (band 6)
850 MHz (band 5)
900 MHz (band 8)
1900 MHz (band 2)
2100 MHz (band 1)
2G (GSM, EDGE, GPRS):
850 MHz
900 MHz
1800 MHz
1900 MHz
Cisco 890 series ISR
with Multimode LTE
feature for global
wireless networks.
C896VAG-LTE-GA-K
9 comes with a Sierra
Wireless MC7304
modem.
Table 1-33 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)
SKU ID Mode
Operating
Region Frequency Band Description
1-81
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
C897VAG-LTE-GA-
K9
LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
Global (Europe,
New Zealand,
and Australia)
4G:
800 MHz (band 20)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
3G (UMTS, HSPA+, HSPA):
800 MHz (band 6)
850 MHz (band 5)
900 MHz (band 8)
1900 MHz (band 2)
2100 MHz (band 1)
2G (GSM, EDGE, GPRS):
850 MHz
900 MHz
1800 MHz
1900 MHz
Cisco 890 series ISR
with Multimode LTE
feature for global
wireless networks.
C897VAG-LTE-GA-K
9 comes with a Sierra
Wireless MC7304
modem.
C897VAMG-LTE-G
A-K9
LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
Global (Europe,
New Zealand,
and Australia)
LTE:
800 MHz (band 20)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
3G (UMTS, HSPA+, HSPA):
800 MHz (band 6)
850 MHz (band 5)
900 MHz (band 8)
1900 MHz (band 2)
2100 MHz (band 1)
2G (GSM, EDGE, GPRS):
850 MHz
900 MHz
1800 MHz
1900 MHz
Cisco 890 series ISR
with Multimode LTE
feature for global
wireless networks.
C897VAMG-LTE-GA
-K9 comes with a
Sierra Wireless
MC7304 modem.
Table 1-33 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)
SKU ID Mode
Operating
Region Frequency Band Description
1-82
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
C897VAG-LTE-LA-
K9
LTE
HSPA+
HSPA
UMTS
Latin America For FDD LTE:
700 MHz (band 28)
850 MHz (band 5)
800 MHz (band 19)
800 MHz (band 18)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
For TDD LTE:
1900 MHz (Band 39)
2300 MHz (Band 40)
2500 MHz (Band 41)
2600 MHz (Band 38)
For UMTS, HSPA+, HSPA:
800 MHz (band 6)
800 MHz (band 19)
850 MHz (band 5)
900 MHz (band 8)
1700 MHz (band 9)
2100 MHz (band 1)
C897VAG-LTE-LA-K
9 is a dedicated
Multimode LTE SKU
for Latin American
wireless networks and
comes with a Sierra
Wireless MC7430
modem.
Table 1-33 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)
SKU ID Mode
Operating
Region Frequency Band Description
1-83
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
C898EAG-LTE-GA
-K9
LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
Global (Europe,
New Zealand,
and Australia)
LTE:
800 MHz (band 20)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
3G (UMTS, HSPA+, HSPA):
800 MHz (band 6)
850 MHz (band 5)
900 MHz (band 8)
1900 MHz (band 2)
2100 MHz (band 1)
2G (GSM, EDGE, GPRS):
850 MHz
900 MHz
1800 MHz
1900 MHz
Cisco 890 series ISR
with Multimode LTE
feature for global
wireless networks.
C898EAG-LTE-GA-K
9 comes with a Sierra
Wireless MC7304
modem.
Table 1-33 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)
SKU ID Mode
Operating
Region Frequency Band Description
1-84
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
C898EAG-LTE-LA-
K9
LTE
HSPA+
HSPA
UMTS
ASEAN For FDD LTE:
700 MHz (band 28)
850 MHz (band 5)
800 MHz (band 19)
800 MHz (band 18)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
For TDD LTE:
1900 MHz (Band 39)
2300 MHz (Band 40)
2500 MHz (Band 41)
2600 MHz (Band 38)
For UMTS, HSPA+, HSPA:
800 MHz (band 6)
800 MHz (band 19)
850 MHz (band 5)
900 MHz (band 8)
1700 MHz (band 9)
2100 MHz (band 1)
C898EAG-LTE-LA-K
9 is a dedicated
Multimode LTE SKU
for Asean wireless
networks and comes
with a Sierra Wireless
MC7430 modem.
Table 1-33 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)
SKU ID Mode
Operating
Region Frequency Band Description
1-85
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
C899G-LTE-LA-K9 LTE
HSPA+
HSPA
UMTS
Latin America
and APAC
For FDD LTE:
700 MHz (band 28)
850 MHz (band 5)
800 MHz (band 19)
800 MHz (band 18)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
For TDD LTE:
1900 MHz (Band 39)
2300 MHz (Band 40)
2500 MHz (Band 41)
2600 MHz (Band 38)
For UMTS, HSPA+, HSPA:
800 MHz (band 6)
800 MHz (band 19)
850 MHz (band 5)
900 MHz (band 8)
1700 MHz (band 9)
2100 MHz (band 1)
C899G-LTE-LA-K9 is
a dedicated Multimode
LTE SKU for Latin
American and APAC
wireless networks and
comes with a Sierra
Wireless MC7430
modem.
Table 1-33 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)
SKU ID Mode
Operating
Region Frequency Band Description
1-86
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
C899G-LTE-GA-K9 LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
Global (Europe,
New Zealand,
and Australia)
LTE:
800 MHz (band 20)
900 MHz (band 8)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
3G (UMTS, HSPA+, HSPA):
800 MHz (band 6)
850 MHz (band 5)
900 MHz (band 8)
1900 MHz (band 2)
2100 MHz (band 1)
2G (GSM, EDGE, GPRS):
850 MHz
900 MHz
1800 MHz
1900 MHz
Cisco 890 series ISR
with Multimode LTE
feature for global
wireless networks.
C899G-LTE-GA-K9
comes with a Sierra
Wireless MC7304
modem.
C899G-LTE-VZ-K9
LTE
EVDO Rev-A
1xRTT
North America
(Verizon)
LTE:
AWS (band 4)
700 MHz (band 13)
PCS 1900 MHz (band 25)
3G:
800 MHz (band class 0)
1900 MHz (band class 1)
800 MHz (band class 10)
2G:
800 MHz (band class 0)
1900 MHz (band class 1)
800 MHz (band class 10)
Cisco 890 series ISR
with Multimode LTE
feature for Verizon
wireless networks.
C899G-LTE-VZ-K9
comes with a Sierra
Wireless MC7350
modem.
Table 1-33 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)
SKU ID Mode
Operating
Region Frequency Band Description
1-87
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
C899G-LTE-NA-K9 LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
North America
(AT&T,
Bell-Canada,
Roger, Telus,
and other
GSM/LTE
operators in
USA and
Canada)
LTE:
AWS (band 4)
700 MHz (band 5)
850 MHz (band 17)
1900 MHz (band 2)
2600 MHz (band 7)
3G (UMTS, HSPA+, HSPA):
1900 MHz (band 2)
AWS (band 4)
850 (band 5)
2G (GSM, EDGE, GPRS):
850 MHz
900 MHz
1800 MHz
1900 MHz
Cisco 890 series ISR
with Multimode LTE
feature for wireless
networks in USA and
Canada.
C899G-LTE-NA-K9
comes with a Sierra
Wireless MC7354
modem.
Table 1-33 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)
SKU ID Mode
Operating
Region Frequency Band Description
1-88
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
C899G-LTE-ST-K9 LTE
EVDO Rev-A
1xRTT
North America
(Sprint)
LTE:
AWS (band 4)
700 MHz (band 13)
PCS 1900 MHz (band 25)
3G:
800 MHz (band class 0)
1900 MHz (band class 1)
800 MHz (band class 10)
2G:
800 MHz (band class 0)
1900 MHz (band class 1)
800 MHz (band class 10)
Cisco 890 series ISR
with Multimode LTE
feature for Sprint
wireless networks.
C899G-LTE-ST-K9
comes with a Sierra
Wireless MC7350
modem.
C899G-LTE-JP-K9
LTE
HSPA+
HSPA
UMTS
EDGE
GPRS
Global (Japan) LTE:
800 MHz (band 20)
850 MHz (band 19)
900 MHz (band 8)
1500 MHz (band 21)
1800 MHz (band 3)
2100 MHz (band 1)
2600 MHz (band 7)
3G (UMTS, HSPA+, HSPA):
800 MHz (band 6)
850 MHz (band 5)
900 MHz (band 8)
1900 MHz (band 2)
2100 MHz (band 1)
2G (GSM, EDGE, GPRS):
850 MHz
900 MHz
1800 MHz
1900 MHz
Cisco 890 series ISR
with Multimode LTE
feature for global
wireless networks.
C899G-LTE-JP-K9
comes with a Sierra
Wireless MC7330
modem.
Table 1-33 Supported 4G LTE SKUs for the Cisco 880 and Cisco 890 Series ISRs (continued)
SKU ID Mode
Operating
Region Frequency Band Description
1-89
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco C881G-4G Integrated Services Router
Figure 1-48 shows the front panel of the Cisco C881G-4G ISR.
Figure 1-48 Front Panel of the Cisco C881G-4G ISR
Table 1-34 describes the LEDs of the Cisco C881G-4G ISR.
372528
6 7 8 9 10 11
1 3
2 4
5
1 Power OK 7 FE LAN
2 PPP 8 GPS
3 PoE 9 RSSI
4 FE WAN Port 10 4G
5 SIM 11 WWAN
6 VPN
Table 1-34 LED Descriptions for the Cisco C881G-4G ISR
Number LED Color Description
1 Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Boot up is in process, or the router is in
ROMMON mode.
Off—Power is not supplied to the router.
2 PPP Green On—At least one PPP session is established.
3 PoE Green On—PoE is connected and powered.
Off—PoE is not installed.
Amber On—Fault with the PoE.
4FE WAN
Port Link
Green On—Port is connected.
Blinking—Data is either being received or transmitted.
Off—Port is not connected.
1-90
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
5 SIM Green / Yellow
(one green blink
followed by two
yellow blinks)
SIM in slot 0 is active, SIM in slot 1 is not.
Yellow / Green
(one yellow
blink followed
by two green
blinks)
SIM in slot 1 active, SIM in slot 0 is not.
Off / Green (two
green blinks
and then a
pause)
No SIM in slot 0, SIM present in slot 1.
Green / Off
(slow blink
once and then a
pause)
SIM is present in slot0, no SIM in slot 1.
Off / Off No SIM present in either slots.
6 VPN Green On—VPN is connected.
7 FE LAN
Port Links
Status
Green On—Ethernet port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Ethernet port is not connected.
8 GPS Green (solid) Standalone GPS.
Green (slow
blinking)
GPS is acquiring signals.
Yellow (solid) Assisted GPS.
Yellow (slow
blinking)
Assisted GPS is acquiring signals.
Off GPS is not configured.
9 RSSI Green (solid) Signal strength bars are indicated by the corresponding
LEDs.
10 Service Green (solid) Service is active and the corresponding LED is lit based
on the service level that is active (2G, 3G,3.7G, LTE).
Off No service.
Table 1-34 LED Descriptions for the Cisco C881G-4G ISR
Number LED Color Description
1-91
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
11 WWAN Green Module is powered on and connected but not
transmitting or receiving.
Green (slow
blinking)
Module is powered on and searching for connection.
Green (fast
blinking)
Module is transmitting or receiving.
Off Module is not powered.
Table 1-34 LED Descriptions for the Cisco C881G-4G ISR
Number LED Color Description
1-92
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-49 shows the back panel of the Cisco C881G-4G ISR.
Figure 1-49 Back Panel of the Cisco C881G-4G ISR
For information on installing the Cisco C880 Series Routers, see:
http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG.html
Cisco C886VAG-LTE
Figure 1-50 shows the front panel of the Cisco C886VAG-LTE ISR.
Figure 1-50 Front Panel of the Cisco C886VAG-LTE ISR
372522
1 2 3 4 5 6 8 1097
11121314
1 Primary WAN port—FE 9 Earth ground connection
2 USB port 10 Kensington security slot
3 4G port 11 4G Antenna connector—M1/DIV
4 SIM slots 12 Power switch
5 4-port 10/100 Ethernet switch 13 Active GPS antenna connector
6 Serial port—Console or auxiliary 14 4G Antenna connector—M0/MAIN
7 Reset button
8 Power connector
372529
6 7 8 9 10 11
1 3
2 4
5
1-93
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-35 describes the LEDs for Cisco C886VAG-LTE ISR.
Table 1-35 LED Descriptions for the Cisco C886VAG-LTE ISR
Number LED Color Description
1 Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Boot up is in process, or the router is in
ROMMON mode.
Off—Power is not supplied to the router.
2 PPP Green On—At least one PPP session is established.
3 PoE Green On—PoE is connected and powered.
Off—PoE is not installed.
Amber On—Fault with the PoE.
4 xDSL CD Green On—The xDSL interface is connected to the DSLAM.
Blinking—Training the line.
Off—Indicates that a connection has not been established
or the port is shut down.
xDSL Data Green Blinking—The xDSL interface is either receiving or
transmitting data.
Off—No data is being transmitted or received.
5 SIM Green / Yellow
(one green blink
followed by two
yellow blinks)
SIM in slot 0 is active, SIM in slot 1 is not.
Yellow / Green
(one yellow
blink followed
by two green
blinks)
SIM in slot 1 is active, SIM in slot 0 is not.
Off / Green (two
green blinks and
then a pause)
No SIM in slot 0, SIM present in slot 1.
Green / Off
(slow blink once
and then a
pause)
SIM present in slot0, no SIM in slot 1.
Off / Off No SIM present in either slots.
6 VPN Green On—VPN is connected.
7 FE LAN
Port Links
Status
Green On—Ethernet port is connected.
Blinking—Data is either being received or transmitted.
Off—Ethernet port is not connected.
1-94
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
8 GPS Green (solid) Standalone GPS.
Green (slow
blinking)
GPS is acquiring signals.
Yellow (solid Assisted GPS.
Yellow (slow
blinking)
Assisted GPS is acquiring signals.
Off GPS is not configured.
9 RSSI Green (solid) Signal strength bars are indicated by the corresponding
LEDs.
10 Service Green (Solid) Service is active and the corresponding LED is lit based on
the service level that is active (2G, 3G, 3.7G, LTE).
Off No service.
11 WWAN Green Module is powered on and connected but not transmitting
or receiving.
Green (slow
blinking)
Module is powered on and searching for connection.
Green (fast
blinking)
Module is transmitting or receiving.
Off Module is not powered.
Table 1-35 LED Descriptions (continued)for the Cisco C886VAG-LTE ISR
Number LED Color Description
1-95
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-51 shows the back panel of the Cisco C886VAG-LTE ISR.
Figure 1-51 Back Panel of the Cisco C886VAG-LTE ISR
Cisco C887VAG-4G Integrated Services Router
Figure 1-52 shows the front panel of the Cisco C887VAG-4G ISR.
Figure 1-52 Front Panel of the Cisco C887VAG-4G ISR
365672
1 2 3 4 5 7 986
10111214 13
Cisco 886VAG-LTE
1 USB port 8 Earth ground connection
2 LTE port 9 Kensington security slot
3 SIM slots 10 LTE antenna connector—M1/DIV
4 4-port 10/100 Ethernet switch 11 Power switch
5 Serial port—Console or auxiliary 12 Active GPS antenna connector
6 Reset button 13 Primary WAN port—VDSL or ADSL over
ISDN
7 Power connector 14 LTE antenna connector—M0/MAIN
372529
6 7 8 9 10 11
1 3
2 4
5
1-96
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-36 describes the LEDs for Cisco C887VAG-4G ISR.
Table 1-36 LED Descriptions for the Cisco C887VAG-4G ISR
Number LED Color Description
1 Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Boot up is in process, or the router is in
ROMMON mode.
Off—Power is not supplied to the router.
2 PPP Green On—At least one PPP session is established.
3 PoE Green On—PoE is connected and powered.
Off—PoE is not installed.
Amber On—Fault with the PoE.
4 xDSL CD Green On—The xDSL interface is connected to the DSLAM.
Blinking—Training the line.
Off—Indicates that a connection has not been established
or the port is shut down.
xDSL Data Green Blinking—The xDSL interface is either receiving or
transmitting data.
Off—No data is being transmitted or received.
5 SIM Green / Yellow
(one green blink
followed by two
yellow blinks)
SIM in slot 0 is active, SIM in slot 1 is not.
Yellow / Green
(one yellow
blink followed
by two green
blinks)
SIM in slot 1 is active, SIM in slot 0 is not.
Off / Green (two
green blinks and
then a pause)
No SIM in slot 0, SIM present in slot 1.
Green / Off
(slow blink once
and then a
pause)
SIM present in slot0, no SIM in slot 1.
Off / Off No SIM present in either slots.
6 VPN Green On—VPN is connected.
7 FE LAN
Port Links
Status
Green On—Ethernet port is connected.
Blinking—Data is either being received or transmitted.
Off—Ethernet port is not connected.
1-97
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
8 GPS Green (solid) Standalone GPS.
Green (slow
blinking)
GPS is acquiring signals.
Yellow (solid Assisted GPS.
Yellow (slow
blinking)
Assisted GPS is acquiring signals.
Off GPS is not configured.
9 RSSI Green (solid) Signal strength bars are indicated by the corresponding
LEDs.
10 Service Green (Solid) Service is active and the corresponding LED is lit based on
the service level that is active (2G, 3G, 3.7G, LTE).
Off No service.
11 WWAN Green Module is powered on and connected but not transmitting
or receiving.
Green (slow
blinking)
Module is powered on and searching for connection.
Green (fast
blinking)
Module is transmitting or receiving.
Off Module is not powered.
Table 1-36 LED Descriptions (continued)for the Cisco C887VAG-4G ISR
Number LED Color Description
1-98
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-53 shows the back panel of the Cisco C887VAG-4G ISR.
Figure 1-53 Back Panel of the Cisco C887VAG-4G ISR
Cisco C896VAG-LTE Integrated Services Router
Figure 1-54 shows the front panel of the Cisco C896VAG-LTE ISR.
Figure 1-54 Front Panel of the Cisco C896VAG-LTE ISR
372523
1 2 3 4 5 7 986
10111214 13
1 USB port 8 Earth ground connection
2 4G port 9 Kensington security slot
3 SIM slots 10 4G antenna connector—M1/DIV
4 4-port 10/100 Ethernet switch 11 Power switch
5 Serial port—Console or auxiliary 12 Active GPS antenna connector
6 Reset button 13 Primary WAN port—VDSL or ADSL over
POTS
7 Power connector 14 4G antenna connector—M0/MAIN
372530
6
7
8
9
10
11
12
13
1 3
2
4
5
1-99
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-37 describes the LEDs for Cisco C896VAG-LTE ISR.
Table 1-37 LED Descriptions for Cisco C896VAG-LTE ISR
Number LED Color Description
1 Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Boot up is in process, or the router is in
ROMMON mode
Off—Power is not supplied to the router.
2 PoE Green On—PoE is connected and powered.
Off—PoE is not installed.
Amber On—Fault with the PoE.
3 GE LAN PoE
Ports
Green/Ambe
r
Green On—Ethernet port is connected.
Amber On—Fault with PoE. There is a fault with the
in-line power supply.
Green/Amber Blinking—Data is either being received or
being transmitted.
Green/Amber Off—Ethernet port is not connected.
4 GE LAN Ports Green On—Ethernet port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Ethernet port is not connected.
5 GE WAN Ports Green On—Port is connected.
Blinking—Data is either being received or transmitted.
Off—Port is not connected.
SFP WAN port Green On—Port is connected.
Blinking—Data is either being received or transmitted.
Off—No link
6 VPN Green On—VPN is connected.
7 PPP Green On—At least one PPP session is established.
8 xDSL CD Green On—The xDSL interface is connected to the DSLAM.
Blinking—Training the line.
Off—Indicates that a connection has not been
established or the port is shut down.
xDSL Data Green Blinking—The xDSL interface is either receiving or
transmitting data.
Off—No data is being transmitted or received.
1-100
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
9 SIM Green /
Yellow (one
green blink
followed by
two yellow
blinks)
SIM in slot 0 is active, SIM in slot 1 is not.
Yellow /
Green (one
yellow blink
followed by
two green
blinks)
SIM in slot 1 is active, SIM in slot 0 is not.
Off / Green
(two green
blinks and
then a pause)
No SIM in slot 0, SIM is present in slot 1.
Green / Off
(slow green
blink once
and then a
pause)
SIM is present in slot0, no SIM in slot 1.
Off / Off No SIM present in either slots.
10 Service Green
(Solid)
Service is active and the corresponding LED is lit based
on the service level that is active (2G, 3G, 3.5G, 3.7G,
LTE).
Off No service.
11 RSSI Green
(solid)
Signal strength bars are indicated by the corresponding
LEDs.
12 GPS Green
(solid)
Standalone GPS.
Green (slow
blinking)
GPS is acquiring signals.
Yellow
(solid)
Assisted GPS.
Yellow
(slow
blinking)
Assisted GPS is acquiring signals.
Off GPS is not configured.
Table 1-37 LED Descriptions (continued)for Cisco C896VAG-LTE ISR
Number LED Color Description
1-101
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-55 shows the back panel of the Cisco C896VAG-LTE ISR.
Figure 1-55 Back Panel of the Cisco C896VAG-LTE ISR
13 WWAN Green Module is powered on and connected but not
transmitting or receiving.
Green (slow
blinking)
Module is powered on and searching for connection.
Green (fast
blinking)
Module is transmitting or receiving.
Off Module is not powered.
Table 1-37 LED Descriptions (continued)for Cisco C896VAG-LTE ISR
Number LED Color Description
372524
1 2 3 4 5 6 7 10 12118 9
131416 15
1-102
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
For information on installing Cisco C890 Series Routers, see the following link:
http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG.html
Cisco C897VAG-LTE Integrated Service Router
Figure 1-56 shows the front panel of the Cisco C897VAG-LTE ISR.
Figure 1-56 Front Panel of the Cisco C897VAG-LTE ISR
1 GE WAN interface 9 On/Off switch
2 SFP port 10 Reset button
3 4G port 11 Earth ground connection
4 USB port 12 Kensington security slot
5 SIM slots 13 4G antenna connector—M1/DIV
6 8-port Gigabit Ethernet switch 14 Active GPS antenna connector
7 Console / Auxiliary port 15 VDSL or ADSL over ISDN
8 Power connector 16 4G antenna connector—M0/MAIN
372531
1 3
2
4
5
6
7
8
9
10
11
12
13
1-103
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-38 describes the LEDs for the Cisco C897VAG-LTE ISR.
Table 1-38 LED Descriptions for the Cisco C897VAG-LTE ISR
Number LED Color Description
1 Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Boot up is in process, or the router is in
ROMMON mode.
Off—Power is not supplied to the router.
2 PoE Green On—PoE is connected and powered.
Off—PoE is not installed.
Amber On—Fault with the PoE.
3 GE LAN PoE
Ports
Green/Ambe
r
Green On—Ethernet port is connected.
Amber On—Fault with PoE. There is a fault with the
in-line power supply.
Green/Amber Blinking—Data is either being received or
being transmitted.
Green/Amber Off—Ethernet port is not connected.
4 GE LAN Ports Green On—Ethernet port is connected.
Blinking—Data is either being received or transmitted.
Off—Ethernet port is not connected.
5 GE WAN Ports Green On—Port is connected.
Blinking—Data is either being received or transmitted.
Off—Port is not connected.
SFP WAN port Green On—Port is connected.
Blinking—Data is either being received or transmitted.
Off—No link
6 VPN Green On—VPN is connected.
7 PPP Green On—At least one PPP session is established.
8 xDSL CD Green On—The xDSL interface is connected to the DSLAM.
Blinking—Training the line.
Off—Indicates that a connection has not been
established or the port is shut down.
xDSL Data Green Blinking—The xDSL interface is either receiving or
transmitting data.
Off—No data is being transmitted or being received.
1-104
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
9 SIM Green /
Yellow (one
green blink
followed by
two yellow
blinks)
SIM in slot 0 is active, SIM in slot 1 is not.
Yellow /
Green (one
yellow blink
followed by
two green
blinks)
SIM in slot 1 is active, SIM in slot 0 is not.
Off / Green
(two green
blinks and
then a pause)
No SIM in slot 0, SIM is present in slot 1.
Green / Off
(slow green
blink once
and then a
pause)
SIM is present in slot0, no SIM in slot 1.
Off / Off No SIM present in either slots.
10 Service Green
(solid)
Service is active and the corresponding LED is lit based
on the service level that is active (2G, 3G, 3.5G, 3.7G,
LTE).
Off No service.
11 RSSI Green
(solid)
Signal strength bars are indicated by the corresponding
LEDs.
12 GPS Green
(solid)
Standalone GPS.
Green (slow
blinking)
GPS is acquiring signals.
Yellow
(solid)
Assisted GPS.
Yellow
(slow
blinking)
Assisted GPS is acquiring signals.
Off GPS is not configured.
Table 1-38 LED Descriptions (continued)for the Cisco C897VAG-LTE ISR
Number LED Color Description
1-105
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-57 shows the back panel of the Cisco C897VAG-LTE ISR.
Figure 1-57 Back Panel of the Cisco C897VAG-LTE ISR
Cisco C898EAG-LTE Integrated Service Router
Figure 1-58 shows the front panel of the Cisco C898EAG-LTE ISR.
Figure 1-58 Front Panel of the Cisco C898EAG-LTE ISR
13 WWAN Green Module is powered on and connected, but not
transmitting or receiving.
Green (slow
blinking)
Module is powered on and searching for connection.
Green (fast
blinking)
Module is transmitting or receiving.
Off Module is not powered.
Table 1-38 LED Descriptions (continued)for the Cisco C897VAG-LTE ISR
Number LED Color Description
372525
1 2 3 4 5 6 7 10 12118 9
131416 15
1 GE WAN interface 9 On/Off switch
2 SFP port 10 Reset button
3 4G port 11 Earth ground connection
4 USB port 12 Kensington security slot
5 SIM slots 13 4G antenna connector—M1/DIV
6 8-port Gigabit Ethernet switch 14 Active GPS antenna connector
7 Console/Auxiliary port 15 VDSL or ADSL over POTS
8 Power connector 16 4G antenna connector—M0/MAIN
1-106
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-39 describes the LEDs for the Cisco C898EAG-LTE ISR.
372532
6
7
8
9
10
11
12
13
1 3
2
4
5
Table 1-39 LED Descriptions for the Cisco C898EAG-LTE ISR
Number LED Color Description
1 Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Boot up is in process, or the router is in
ROMMON mode.
Off—Power is not supplied to the router.
2 PoE Green On—PoE is connected and powered.
Off—PoE is not installed.
Amber On—Fault with the PoE.
3 GE LAN PoE
Ports
Green/Ambe
r
Amber On—Ethernet port is connected.
Amber On—Fault with PoE. There is a fault with the
in-line power supply.
Green/Amber Blinking—Data is either being received or
transmitted.
Green/Amber Off—Ethernet port is not connected.
4 GE LAN Ports Green On—Ethernet port is connected.
Blinking—Data is either being received or transmitted.
Off—Ethernet port is not connected.
5 GE WAN Ports Green On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Port is not connected.
SFP WAN port Green On—Port is connected.
Blinking—Data is either being received or transmitted.
Off—No link
6 VPN Green On—VPN is connected.
1-107
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
7 PPP Green On—At least one PPP session is established.
8 xDSL CD Green On—The xDSL interface is connected to the DSLAM40.
Blinking—Training the line.
Off—Indicates that a connection has not been
established or the port is shut down.
xDSL Data Green Blinking—The xDSL interface is either receiving or
transmitting data.
Off—No data is being transmitted or being received.
xDSL EFM Green Blink—The router is operating in EFM mode.
Off—Not operating in EFM mode.
9 SIM Green /
Yellow (one
green blink
followed by
two yellow
blinks)
SIM in slot 0 is active, SIM in slot 1 is not.
Yellow /
Green (one
yellow blink
followed by
two green
blinks)
SIM in slot 1 is active, SIM in slot 0 is not.
Off / Green
(two green
blinks and
then a pause)
No SIM in slot 0, SIM present in slot 1.
Green / Off
(slow green
blink once
and then a
pause)
SIM is present in slot0, no SIM in slot 1.
Off / Off No SIM present in either slot.
10 Service Green
(Solid)
Service is active and the corresponding LED is lit based
on the service level which is active (2G, 3G, 3.5G, 3.7 G,
LTE).
Off No service.
11 RSSI Green
(solid)
Signal strength bars are indicated by the corresponding
LEDs.
Table 1-39 LED Descriptions (continued)for the Cisco C898EAG-LTE ISR
Number LED Color Description
1-108
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
12 GPS Green
(solid)
Standalone GPS
Green (slow
blinking)
GPS is acquiring signals.
Yellow
(solid)
Assisted GPS.
Yellow
(slow
blinking)
Assisted GPS is acquiring signals.
Off GPS is not configured.
13 WWAN Green Module is powered on and connected, but not
transmitting or receiving.
Green (slow
blinking)
Module is powered on and searching for connection.
Green (fast
blinking)
Module is transmitting or receiving.
Off Module is not powered.
Table 1-39 LED Descriptions (continued)for the Cisco C898EAG-LTE ISR
Number LED Color Description
1-109
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-59 shows the back panel of the Cisco C898EAG-LTE ISR.
Figure 1-59 Back Panel of the Cisco C898EAG-LTE ISR
Cisco C899G-LTE Integrated Service Router
Figure 1-60 shows the front panel of the Cisco C899G-LTE ISR.
Figure 1-60 Front Panel of the Cisco C899G-LTE ISR
372526
1 2 3 4 5 6 7 10 12118 9
131416 15
1 GE WAN interface 9 On/Off switch
2 SFP port 10 Reset button
3 4G port 11 Earth ground connection
4 USB port 12 Kensington security slot
5 SIM slots 13 4G antenna connector—M1/DIV
6 8-port Gigabit Ethernet switch 14 Active GPS antenna connector
7 Console/Auxiliary port 15 G.SHDSL over POTS
8 Power connector 16 4G antenna connector—M0/MAIN
372533
1 3
2
4
5
6
7
8
9
10
11
12
1-110
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-40 describes the LEDs for the Cisco C899G-LTE ISR.
Table 1-40 LED Descriptions for the Cisco C899G-LTE ISR
Number LED Color Description
1 Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Boot up is in process, or the router is in
ROMMON mode.
Off—Power is not supplied to the router.
2 PoE Green On—PoE is connected and powered.
Off—PoE is not installed.
Amber On—Fault with the PoE.
3 GE LAN PoE
Ports
Green Green On—Ethernet port is connected.
Amber On—Fault with PoE. There is a fault with the
in-line power supply.
Green/Amber Blinking—Data is either being received or
transmitted.
Green/Amber Off—Ethernet port is not connected.
4 GE LAN Ports Green On—Ethernet port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Ethernet port is not connected.
5GE WAN
Ports
Green On—Port is connected.
Blinking—Data is either being received or transmitted.
Off—Port is not connected.
SFP WAN port Green On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—No link
6 VPN Green On—VPN is connected.
7 PPP Green On—At least one PPP session is established.
1-111
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
8 SIM Green / Yellow
(one green blink
followed by two
yellow blinks)
SIM in slot 0 is active, SIM in slot 1 is not.
Yellow / Green
(one yellow blink
followed by two
green blinks)
SIM in slot 1 is active, SIM in slot 0 is not.
Off / Green (two
green blinks and
then a pause)
No SIM in slot 0, SIM present in slot 1.
Green / Off (slow
green blink once
and then a pause)
SIM is present in slot0, no SIM in slot 1.
Off / Off No SIM present in either slots.
9 Service Green (Solid) Service is active and the corresponding LED is lit based
on the service level which is active (2G, 3G, 3.5G, 3.7G,
LTE).
Off No service.
10 RSSI Green (solid) Signal strength bars are indicated by the corresponding
LEDs.
11 GPS Green (solid) Standalone GPS.
Green (slow
blinking)
GPS is acquiring signals.
Yellow (solid) Assisted GPS.
Yellow (slow
blinking)
Assisted GPS is acquiring signals.
Off GPS is not configured.
12 WWAN Green Module is powered on and connected, but not
transmitting or receiving.
Green (slow
blinking)
Module is powered on and searching for connection.
Green (fast
blinking)
Module is transmitting or receiving.
Off Module is not powered.
Table 1-40 LED Descriptions for the Cisco C899G-LTE ISR (continued)
Number LED Color Description
1-112
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-61 shows the back panel of the Cisco C899G-LTE ISR.
Figure 1-61 Back Panel of the Cisco C899G-LTE ISR
1-113
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
372527
1 2 3 4 5 6 7 8 11 1312109
141516
1 GE WAN interface 9 Power connector
2 GE WAN interface 10 On/Off switch
3 SFP port 11 Reset button
4 4G port 12 Earth ground connection
5 USB port 13 Kensington security slot
6 SIM slots 14 4G antenna connector—M1/DIV
7 8-port Gigabit Ethernet switch 15 Active GPS antenna connector
8 Console/Auxiliary port 16 4G antenna connector—M0/MAIN
1-114
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco 890 Series Integrated Service Routers
This section contains the following topics:
Cisco 891, Cisco 892, and Cisco 892F, page 1-114
Cisco C897VAB-K9, page 1-124
Cisco 891, Cisco 892, and Cisco 892F
The Cisco 891, Cisco 892, and Cisco 892F ISRs have the following features:
Integrated 8-port 10/100 Ethernet switch for connecting to the LAN
10/100 FE and 10/100/1000 Gigabit Ethernet (GE) port for connecting to the WAN
Separate console and auxiliary ports
(Optional) embedded Wi-Fi certified dual-radio 802.11a/b/g/n-compliant wireless AP
Optional 4-port PoE
Note The Cisco 890 Series ISRs can include an optional PoE module that provides power to
802.3af-compliant devices connected to Ethernet ports 0 through 3. If this feature was not
configured with the factory order, you must order and install it to enable the PoE function.
Note On a Cisco 891 series router, due to TCAM limitation, you can apply an ACL configuration on
maximum 9 ports. If you apply the ACL configuration beyond 9 ports, the configuration will not
be applied, and the router will display an error message.
Note Layer 2 FastEthernet ports of Cisco 800 series routers do not support Downloadable
ACL(dACL). Layer 2 GigabitEthernet ports support downloadable ACL(dACL).
Security feature card (SFC) socket
DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB
system memory in Cisco 891 and Cisco 892 ISRs, and a total of 1 GB system memory in
Cisco 892F series ISRs
Three reverse-polarity Threaded Neill-Concelman (RP-TNC) connectors on the back panel for
non-captive dual-band WLAN antenna (wireless models only)
Support for the AIM2-CUE-K9 and AIM2-APPRE-104-K9
GE small-form-factor pluggable (SFP) port (Cisco 892F series ISRs only)
The following feature is located on the front panel of
Two USB 2.0 ports
1-115
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-62 shows the front panel details of the Cisco 890 Series router.
Figure 1-62 Front Panel of the Cisco 890 Series ISR
Figure 1-63 shows the back panel details of the Cisco 892W router. Non wireless routers do not have
RP-TNC antennas or connectors on the back panel. Some of the features that are shown may not be
available on your router. However, the feature locations are similar across all Cisco 890 series routers.
Figure 1-63 Back Panel of the Cisco 892W Router
1 LEDs 2 USB ports
272367
1 2
1 Antenna—Dipole swivel antenna attached to
RP-TNC connectors (wireless models only)
7 PoE power connector for optional PoE
module
1
2 Backup—Data BRI
2
or V.92
3
port 8 Reset button
3 Primary WAN port—FE and GE 9 Power connector
272369
1
4 5 6 8 9 10 1172 3
1-116
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-64 shows the location of the SFP port on a Cisco 892FW router.
Figure 1-64 SFP Port Location on a Cisco 892FW Router
Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA
The Cisco 892FSP, Cisco 896VA, Cisco897VA (includes Cisco 897VA, Cisco 897VAM, Cisco 897VAW,
Cisco 897VAMW), and Cisco 898EA routers have the following features:
Integrated 8-port 10/100/1000 Gigabit Ethernet switch for connecting to the LAN
Two 10/100/1000 GE ports for Cisco 892FSP
One 10/100/1000 GE port for Cisco 896VA, 897VA, and the Cisco 898EA. Either the SFP socket or
the 10/100/1000 GE port can be active at a given time, but not both.
Single console and auxiliary ports for configuration and management
512 MB of on-board memory (upgrade option to 1 GB)
256 MB flash memory for Cisco 896VA, Cisco 897VA, and Cisco 898EA
One USB 2.0 port
Optional internal adapter for inline PoE on four switch ports for IP phones or external wireless
access points for Cisco 896VA, Cisco 897VA, and Cisco 898EA models only. No PoE support on
Cisco 892FSP.
4 Auxiliary port 10 Earth ground connection
5 Console port 11 Kensington security slot
6 8-port 10/100 Ethernet switch
1. The Cisco 890 Series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
to Ethernet ports 0 through 3. If this feature was not configured with the factory order you must order and install it to enable
the PoE function.
2. The Data BRI port is available only on the Cisco 892 Router models.
3. The V.92 port (not shown) is available only on the Cisco 891 Router models and is located between the console port and the
Ethernet switch.
1 SFP port 2 SFP LEDs
278179
Cisco 892F-W
SFP
EN
S
21
1-117
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Note The Cisco 892FSP does not support AIM2-CUE-K9 and AIM2-APPRE-104-K9 because it does not have
an SFC socket.
Note To upgrade DRAM memory from 512 MB to 1 GB on the Cisco 892FSP, Cisco 896VA, Cisco 897VA,
and Cisco 898EA routers, you should enable the FL-8XX-512U1GB license.
1-118
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-65 shows the back panel of the Cisco 892FSP Router.
Figure 1-65 Back Panel of the Cisco 892FSP Router
Figure 1-66 shows the front panel of the Cisco 892FSP Router.
Figure 1-66 Front Panel of the Cisco 892FSP Router
9
GE WAN
8
GE WAN
SFP
8
12VDC 2.5A
CONSOLE
AUX
RESET
Cisco 892FSP
284781
2 3 4 5 6 8 9 1071
1 GE WAN interface 6 Power connector
2 SFP port 7 On/Off switch
3 USB port 8 Reset button
4 8-port Gigabit Ethernet switch 9 Earth ground connection
5 Console/Auxiliary port 10 Kensington security slot
284782
1
1 LEDs
1-119
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-67 shows the back panel of the Cisco 896VA Router.
Figure 1-67 Back Panel of the Cisco 896VA Router
Figure 1-68 shows the front panel of the Cisco 896VA and the Cisco 897VA routers.
Figure 1-68 Front Panel of the Cisco 896VA and Cisco 897VA Routers
7 6 GELAN 5 4
3 2 POE 1 0
0
ISDN
8
GE WAN
54VDC 1.2A
12VDC 2.5A
VDSL/ADSL
overISDN
CONSOLE
RESET
Cisco 896VA
12
1 2 3 4 5 8 9 10 11
6 7
344766
1 ISDN 7 Power connector
2 GE WAN interface 8 On/Off switch
3 SFP port 9 Reset button
4 USB port 10 Earth ground connection
5 8-port Gigabit Ethernet switch
1
11 Kensington security slot
6 Console/Auxiliary port 12 VDSL / ADSL over ISDN
1. Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature is not configured with
the factory order, you must order and install it to enable the PoE function.
1
344765
1 LEDs
1-120
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-69 shows the back panel of the Cisco 897VA Router.
Figure 1-69 Back Panel of the Cisco 897VA Router
Figure 1-70 shows the back panel of the Cisco 897VAM Router.
Figure 1-70 Back Panel of the Cisco 897VAM Router
7 6 GELAN 5 4
3 2 POE 1 0
0
ISDN
8
GE WAN
54VDC 1.2A
12VDC 2.5A
VDSL/ADSL
overPOTS
CONSOLE
RESET
Cisco 897VA
344767
12
1 2 3 4 5 8 9 10 11
6 7
1 ISDN 7 Power connector
2 GE WAN interface 8 On/Off switch
3 SFP port 9 Reset button
4 USB port 10 Earth ground connection
5 8-port Gigabit Ethernet switch
1
11 Kensington security slot
6 Console/Auxiliary port 12 VDSL/ADSL over POTS
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
the factory order, you must order and install it to enable the PoE function.
7 6 GELAN 5 4
3 2 POE 1 0
8
GE WAN
54VDC 1.2A
12VDC 2.5A
VDSL/ADSL
overPOTS
CONSOLE
RESET
344769
11
1 2 3 4 7 8 9 10
5 6
1 GE WAN interface 7 On/Off switch
2 SFP port 8 Reset button
3 USB port 9 Earth ground connection
1-121
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-71 shows the front panel of the Cisco 897VAM router.
Figure 1-71 Front Panel of the Cisco 897VAM Router
Figure 1-72 shows the back panel of the Cisco 897VAW router.
Figure 1-72 Back Panel of the Cisco 897VAW Router
4 8-port Gigabit Ethernet switch
1
10 Kensington security slot
5 Console / Auxiliary port 11 VDSL / ADSL over POTS
6 Power connector
1. Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature was not configured
with the factory order, you must order and install it to enable the PoE function.
1
344768
1 LEDs
7 6 GELAN 5 4
3 2 POE 1 0
8
GE WAN
54VDC 1.2A
12VDC 2.5A
VDSL/ADSL
overPOTS
CONSOLE
RESET
344771
11
1 2 3 4 7 8 9 10
5 6
1 GE WAN interface 7 On/Off switch
2 SFP port 8 Reset button
3 USB port 9 Earth ground connection
4 8-port Gigabit Ethernet switch
1
10 Kensington security slot
5 Console / Auxiliary port 11 VDSL / ADSL over POTS
6 Power connector
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
the factory order, you must order and install it to enable the PoE function.
1-122
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-73 shows the front panel of the Cisco 897VAW and the Cisco 897VAMW routers.
Figure 1-73 Front Panel of the Cisco 897VAW and the Cisco 897VAMW Routers
Figure 1-74 shows the back panel of the Cisco 897VAMW Router.
Figure 1-74 Back Panel of the Cisco 897VAMW Router
1
344770
1 LEDs
7 6 GELAN 5 4
3 2 POE 1 0
8
GE WAN
54VDC 1.2A
12VDC 2.5A
VDSL/ADSL
overPOTS
CONSOLE
RESET
344772
11
1 2 3 4 7 8 9 10
5 6
1 GE WAN interface 7 On/Off switch
2 SFP port 8 Reset button
3 USB port 9 Earth ground connection
4 8-port Gigabit Ethernet switch
1
10 Kensington security slot
5 Console/Auxiliary port 11 VDSL / ADSL over POTS
6 Power connector
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
the factory order, you must order and install it to enable the PoE function.
1-123
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-75 shows the back panel of the Cisco 898EA router.
Figure 1-75 Back Panel of the Cisco 898EA Router
Caution The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN
port may occur if a non-RJ-45 connector is inserted.
Figure 1-76 shows the front panel of the Cisco 898EA Router.
Figure 1-76 Front Panel of the Cisco 898EA Router
7 6 GELAN 5 4
3 2 POE 1 0
8
GE WAN
SFP
8
54VDC 1.2A
12VDC 2.5A
SHDSL
RJ45 ONLY
CONSOLE
RESET
Cisco 898EA
AUX
344774
11
1 2 3 4 7 8 9 10
5 6
1 GE WAN interface 7 On/Off switch
2 SFP port 8 Reset button
3 USB port 9 Earth ground connection
4 8-port Gigabit Ethernet switch
1
1. Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature is not configured with
the factory order, you must order and install it to enable the PoE function.
10 Kensington security slot
5 Console/Auxiliary port 11 SHDSL (RJ45 only)
6 Power connector
1
344773
1 LEDs
1-124
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco C897VAB-K9
The Cisco 897VAB-K9 ISR is designed to support 2-pair VDSL2 bonding up to the 17a profile and single
pair support for ADSL/VDSL over POTS up to the 30a profile.
Table 1-41 provides information about important hardware specifications pertaining to Cisco
C897VAB-K9 ISR.
Figure 1-77 shows the back panel of the Cisco 897VAB-K9 ISR.
Figure 1-77 Back panel of the Cisco 897VAB-K9 ISR
Table 1-41 Hardware Specifications of Cisco C897VAB-K9 ISR
Hardware Description
Flash Memory 256 MB
Main Memory 1-GB DDR RAM; fixed and not extendable
USB port A USB 2.0-compliant port located on the back
panel
FAN Fanless chassis
PoE (Optional) Four internal PoE ports
Primary WAN VDSL/ADSL over POTS
Backup WAN 10/100/1000 GE port (RJ-45/SFP)
Console or auxiliary port RJ-45
LAN switch 8-port 10/100/1000 GE Switch
ISDN
over POTS,VDSL
364228
1 2 3 4 5 6 7 10 12118 9
B
1 Primary WAN VDSL / ADSL over POTS,
VDSL2 Bonding
1
7 Console/Auxiliary Port
2 SFP port 8 Power Connector
3 GE WAN Interface 9 On/Off Switch
4 ISDN 10 Reset Button
5 USB Port 11 Earth Ground connection
6 8-port Gigabit Ethernet Switch
2
12 Kensington Security slot
1-125
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Caution The primary WAN port is designed for an RJ-11 or RJ-14 connector only. Damage to the
primary WAN port may occur if a non-RJ-11 or RJ-14 connector is inserted.
Figure 1-78 shows the front panel of the Cisco 897VAB-K9 ISR.
Figure 1-78 Front panel of the Cisco 897 VAB-K9 ISR
Table 1-42 describes the LEDs for the Cisco 897VAB-K9 ISR.
1. 1.ADSL and VDSL (up to 17a) single-pair functionality uses the center pair of pins in the RJ-11 connector. VDSL 30a single
pair functionality makes use of the pins just adjacent to the center pins. VDSL Bonding makes use of both the center pair pins
& those just adjacent to the center pair to provide the 2 bonded VDSL lines. For more information, see Cisco 890 Series
Integrated Services Routers Data Sheet.
2. 2.Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature is not configured
with the factory order, you must order and install it to enable the PoE function.
364227
CD0 CD1 B1 B2
ISDN
1 3
2
4
5
6
7
8
9
Table 1-42 LED Descriptions for the Cisco 897VAB-K9 ISR
Number LED Color Description
1 Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Boot up is in process, or the router is in ROM
Monitor (ROMMON) mode.
Off—Power is not supplied to the router.
2 PoE OK Green/Yellow Off—Both POE card & POE power supply are not
present.
Yellow On—Either POE card or POE power supply is
not present.
Green On—Both POE card & POE power supply are
present.
1-126
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
3 GE LAN 0
GE LAN 1
GE LAN 2
GE LAN 3
Green/Yellow Off—No link.
Green On—Link.
Yellow On—Fault with PoE. Implies no link.
Green Blinking—Data is either being received or
transmitted.
4 GE LAN 4
GE LAN 5
GE LAN 6
GE LAN 7
Green Off—No link.
On—Link.
Blinking—Data is either being received or being
transmitted.
5 GE WAN 8 Green Off—No link.
On—Link.
Blinking—Data is either being received or being
transmitted.
SFP WAN 8 Green Off—No link.
On—Link.
Blinking—Data is either being received or being
transmitted.
6 VPN Green Off—No tunnel.
On—At least one tunnel is up.
7 PPP Green Off—No PPP session.
On—At least one PPP session established.
8 xDSL CD0 Green Off—Interface is shutdown.
On—Showtime, Link up.
Slow Blinking—Modem initialization.
Fast Blinking—Training up the line.
If both CD0 & CD1 are ON then VDSL Bonding is
active.
xDSL CD1
xDSL DATA Green Off—No Data.
Blinking—Data is either being received or transmitted.
9 ISDN B1 Green Blinking—Data is either being received or transmitted.
Off—No Data.
ISDN B2
Table 1-42 LED Descriptions for the Cisco 897VAB-K9 ISR (continued)
Number LED Color Description
1-127
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco C891 Series ISRs
Cisco C891 Series ISRs are designed to deliver secure broadband, metro Ethernet, wireless LAN
(WLAN) connectivity, and business continuity. Cisco C891 Series ISRs also provide a 1-port Gigabit
Ethernet SFP socket for WAN connectivity.
This section includes the hardware information for the following models:
Cisco C891F
Cisco C891FW
Table 1-43 provides information about the hardware specifications of the Cisco C891 Series Routers.
For detailed hardware specifications, see the Cisco C890 Series hardware data sheet at:
http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78-519930.html
Cisco C891F Router
Figure 1-79 shows the front panel of the Cisco C891F Router.
Table 1-43 Hardware Specifications of Cisco C891 Series ISR
Hardware Description
Flash Memory 256 MB
Main Memory 1-GB DDR RAM; fixed and not extendable
USB port A USB 2.0-compliant port located on the back
panel
FAN Fanless chassis
PoE 4 PoE ports
WAN 1-port GE or 1-port SFP
Data Backup
1-port FE
1-port ISDN
1-port V.92
Console or auxiliary port RJ-45
LAN switch 8-port Gigabit Ethernet
Embedded Wireless AP Dual 802.11b/g/n and 802.11a/n radios for
C891FW
1-128
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-79 Front Panel of the Cisco C891F Router
For detailed description about the LEDs on the Cisco C890 Series Routers, see the “LEDs” section on
page 1-30.
361136
Cisco
Cisco
800
Series
OK
OK
P
OE
OE
PPP
PPP
GE
GE LAN
VPN
V.92
V.92
ISDN
ISDN
OK
OK 0
1 2
3 4
5
6
7
GE8
GE8
SFP8
SFP8
FE0
FE0
WAN
WAN
B1
B1
B2
B2
P
OE
OE
1
1 LEDs
1-129
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-80 shows the back panel of the Cisco C891F Router.
Figure 1-80 Back Panel of the Cisco C891F Router
For information on installing the Cisco C890 Series Routers, see:
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
l880-860.html
Cisco C891FW Router
Figure 1-81 shows the front panel of the Cisco C891FW Router.
Figure 1-81 Front Panel of the Cisco C891FW Router
For detailed description about the LEDs on Cisco C890 Series Router, see “LEDs” section on page 1-30.
361137
FE
FE W
AN
AN
ISDN
ISDN
GE
GE W
AN
AN
SFP
SFP
V
.92
.92
7 6
GE
GE L
AN
AN
C
ON
ONS
OLE
OLE
Ci
Cisco
89
891F
RES
RESET
A
UX
UX
5 4
3 2
POE
POE 1
0
0
0
8 8
0
54V
54VDC 1
.5A
.5A
3.5-5A
3.5-5A
12V
12VDC
(POE)
(POE)
1 2 3 4 5 7 8 13129 11
10
6
1 Back up WAN port—FE WAN 8 Console/Auxiliary port
2 ISDN 9 Power connector
3 Primary WAN port—GE WAN 10 On/Off switch
4 SFP 11 Reset button
5 USB port 12 Earth ground connection
6 V.92 backup 13 Kensington security slot
7 8-port 10/100/1000 Ethernet switch
361138
OK
POE
PPP
GE LAN
VPN
V.92
ISDN
OK 0
12
34
5
6
7
GE8
SFP8
FE0
5GHz
2.4GHz
WAN
B1
B2
POE
Cisco
800
Series
1
1 LEDs
1-130
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-82 shows the back panel of the Cisco C891FW Router.
Figure 1-82 Back Panel of the Cisco C891FW Router
For information on installing the Cisco C890 Series Routers, see:
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
l880-860.html
361139
FE
FE W
AN
AN
ISDN
ISDN
GE
GE W
AN
AN
SFP
SFP
V
.92
.92
7 6
GE
GE L
AN
AN
C
ON
ONS
OLE
OLE
Ci
Cisco
89
891
FW
FW
RES
RESET
A
UX
UX
5 4
3 2
POE
POE 1
0
0
0
8 8
0
54V
54VDC 1
.5A
.5A
3.5-5A
3.5-5A
12V
12VDC
(POE)
(POE)
1 2 3 4 5 7 8 13129 11
10
6
1 Back up WAN port—FE 8 Serial port—Console or auxiliary
2 ISDN 9 Power connector
3 Primary WAN port—GE 10 On/Off switch
4 SFP port 11 Reset button
5 USB port 12 Earth ground connection
6 V.92 backup port 13 Kensington security slot
7 8-port 10/100/1000 Ethernet switch
1-131
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco C891-24X/K9 Integrated Services Router
Cisco C891-24X/K9 Integrated Services Router (ISR) is a fixed Cisco 890 Series ISR that supports 24
port GE LAN. Cisco C891-24X/K9 ISR provides more switch port options compared to other 890 Series
ISRs and Cisco C891-24X/K9 ISR is useful in deployment scenarios where more switching capability
is required. Cisco C891-24X/K9 ISR also supports PoE on 8 switch ports. Cisco C891-24X/K9 ISR
supports WAN connectivity through dual GE or SFP ports.
Table 1-44 provides information about important hardware specifications pertaining to Cisco
C891-24X/K9 ISR.
Figure 1-83 shows the front panel of the Cisco C891-24X/K9 ISR.
Figure 1-83 Front Panel of the Cisco C891-24X/K9 ISR
Table 1-44 Hardware Specifications for Cisco C891-24X/K9 ISR
Hardware Description
Flash Memory 256 MB Flash and 8 MB serial boot flash
Main Memory 1-GB DDR RAM
USB port A USB 2.0-compliant port located at the back
panel
PoE 8 PoE ports
WAN 2-port GE WAN (copper or SFP)
Console or auxiliary port RJ-45
LAN switch 24-port 10/100/1000 BASE-T
Fan Fan less Chassis
POWER
1-132
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-84 shows the back panel of the Cisco C891-24X/K9 ISR.
Figure 1-84 Back Panel of the Cisco C891-24X/K9 ISR
For information on installing the C891-24X/K9 ISR see the following link:
http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG/installin
g.html
Hardware Features
This section provides an overview of the following hardware features for the Cisco 860 Series, 880
Series, and 890 Series ISRs. A feature summary is available at the end of this section.
Kensington Lock
Reset Button
LEDs
Memory
USB Port
Fan
Power Supply
Power over Ethernet Module
3G Cellular Data WAN Connectivity
Small Form-Factor Pluggable Port
Feature Summary
364240
SYSTEM
Cisco C891-24X
POE Enabled GE LAN
1 2 3 4 5 8 9 10 116 7
1 Console or auxiliary port 7 SFP port
2 Reset Button 8 GE WAN port
3 USB port 9 SFP port
4 PoE enabled GE LAN ports 10 System LED
5 GE LAN ports 11 Kensington security slot
6 GE WAN port
1-133
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Kensington Lock
A Kensington security slot is located on the router back panel. To secure the router to a desktop or other
surface, use the Kensington lockdown equipment.
Reset Button
The Reset button is used to restore the router to the factory default configuration or to load a custom
configuration file.
There are two different ways to do this:
By pressing the Reset button within 5 seconds of powering up the router.
By pressing the Reset button for 5 seconds while running IOS software.
Note If you execute a CLI reboot command while the embedded wireless AP is running Cisco Unified
Wireless Network software, the router reboots, but the AP continues to run. Clients with Cisco Unified
Wireless Network software are controlled by a wireless LAN controller (WLC) and can be reset only by
the controller.
Cisco 860VAE Routers—Custom Configuration File
On the Cisco 860VAE routers, the reset button can be used to load a custom configuration file without
having to use the CLI. The configuration file can be located on an external USB flash drive or on the
router's compact flash.
The custom configuration file must be named one of the following:
customer-config
SN-customer-config (where “SN” is the unique hardware serial number)
When the system attempts to load a custom configuration file, configuration files on a USB flash drive
have priority over configuration files on the router's flash drive and the SN-customer-config file name
has priority over the customer-config file name. The priority for loading a configuration file is as
follows:
1. USB flash0—SN-customer-config
2. USB flash0—customer-config
3. Router flash—SN-customer-config
4. Router flash—customer-config
If the router does not find a valid custom configuration file, the system aborts the process.
To reset the router to the factory default configuration, follow these steps:
Step 1 Verify that Cisco IOS is running correctly by checking that the system status LED is on.
1-134
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
5 seconds.
The router reloads itself after the startup configuration has been replaced with the new customer
configuration.
Custom Configuration File for Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA
In the first method, the configuration file can be located on the router's compact flash or on the router's
NVRAM. The custom configuration file must use cfg as the filename extension.
When the system attempts to load a custom configuration file, configuration files on NVRAM have
priority over configuration files on the router's compact flash.
The priority for loading a configuration file is as follows:
1. nvram: *.cfg
2. Router flash: *.cfg
If the router does not find a valid custom configuration file, the system aborts the process.To reset the
router to the factory default configuration or to load a custom configuration file, follow these steps:
Step 1 Turn the power on.
Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
5 seconds.
The router reloads itself after the startup configuration has been replaced with the new customer
configuration.
In the second method, the configuration file can be located on an external USB flash drive or on the
router's compact flash.
The custom configuration file must be named one of the following:
customer-config
customer-config.SN, where "SN" is the unique hardware serial number.
When the system attempts to load a custom configuration file, configuration files on a USB flash drive
have priority over configuration files on the router's flash drive and the "customer-config.SN" file name
has priority over the customer-config file name.
The priority for loading a configuration file is as follows:
1. usbflash0:customer-config.SN
2. usbflash0:customer-config
3. Router flash:customer-config.SN
4. Router flash:customer-config
If the router does not find a valid custom configuration file, the system aborts the process.
To reset the router to the factory default configuration or to load a custom configuration file, follow these
steps:
Step 1 Verify that Cisco IOS is running correctly by checking that the system status LED is on.
1-135
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
5 seconds.
The router reloads itself after the startup configuration has been replaced with the new customer
configuration.
LEDs
The LEDs are located on the front panel of the router.
Table 1-45 describes the LEDs for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series
ISRs.
Table 1-46 lists the LED descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and
Cisco 867VAE-K9 ISRs.
Table 1-47 lists the LED description for the Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco
898EA ISRs.
For a description of LEDs for Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco
860VAE-POE-W-A-K9 ISRs models, see the “Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9,
and Cisco 860VAE-POE-W-A-K9 ISRs” section on page 1-50.
Table 1-45 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs
LED Color Description 860 Series 880 Series 890 Series
Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Bootup is in process, or the router is in
Rommon monitor mode.
Off—Power is not supplied to the router.
All models All models All models
Link Status FE0 Green On—Ethernet port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Ethernet port is not connected.
All models All models All models
Link Status FE1
Link Status FE2
Link Status FE3
Link Status FE4 Green On—Ethernet port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Ethernet port is not connected.
All models
Link Status FE5
Link Status FE6
Link Status FE7
FE WAN Port
Link Status
Green On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Port is not connected.
861
models
881
models
All models
GE WAN Port
Link Status
Green On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Port is not connected.
All models
1-136
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
WLAN
(2.4 GHz)
Green On—Radio is connected, SSID
1
is configured, and client
is associated, but no data is being received or being
transmitted.
Slow blinking—Radio is connected, SSID is configured,
and beacons are being transmitted.
Fast blinking—Data is either being received or being
transmitted.
Off—Radio is shut down, and no SSID is configured.
Wireless
models
Wireless
models
Wireless
models
WLAN (5 GHz) Green On—Radio is connected, SSID is configured, and client is
associated, but no data is being received or being
transmitted.
Slow blinking—Radio is connected, SSID is configured,
and beacons are being transmitted.
Fast blinking—Data is either being received or being
transmitted.
Off—Radio is shut down, and no SSID is configured.
Wireless
models
Wireless
models
WLAN LINK
(Autonomous
Mode)
Green On—Wireless link is up.
Blinking—Ethernet link is up, and data is either being
received or being transmitted.
Off—Wireless link is down.
Wireless
models
Wireless
models
Wireless
models
WLAN LINK
(Unified Mode)
Green On—Ethernet link is up, and wireless access point (AP) is
communicating with LWAPP
2
controller.
Blinking—Ethernet link is up, but wireless AP is not
communicating with LWAPP controller.
Off—Ethernet link is down.
Wireless
models
Wireless
models
PoE Green On—PoE is connected and powered.
Off—PoE is not installed.
—Models
with PoE
Models
with PoE
Amber On—Fault with the PoE.
VPN Green On—VPN is connected. All models All models
PPP
3
Green On—At least one PPP session is established. All models All models
xDSL
4
CD Green On—The xDSL interface is connected to the DSLAM
5
.
Blinking—Training to the line.
Off—Indicates that a connection has not been established
or the port is shut down.
886,
886VA,
887,
887VA,
887VA-M
888
models
896VA,
897VA,
898EA,
897VAB
Table 1-45 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED Color Description 860 Series 880 Series 890 Series
1-137
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
xDSL Data Green Blinking—The xDSL interface is either receiving or
transmitting data.
Off—No data is being transmitted or being received.
886,
886VA,
887,
887VA,
887VA-M
888
models
896VA,
897VA,
898EA,
897VAB
xDSL ATM Green On—The router is operating in ATM
6
mode.
Off—Not operating in ATM mode.
888E
xDSL EFM Green Blink—The router is operating in EFM
7
mode.
Off—Not operating in EFM mode.
898EA
Data BRI LINK Green On—ISDN D channel is connected. 887, 888
models
892
models
Data BRI B1 Green Blinking—B1 channel is either receiving or sending data,
or data is passing through ISDN channel 1.
887, 888
models
892
models
Data BRI B2 Green Blinking—B2 channel is receiving or sending data, or
data is passing through ISDN channel 2.
887, 887V,
888
models
892
models
3G
8
WWAN
9
Green On—Service is established.
Slow Blinking—Searching for service.
Fast Blinking—Data is either being received or being
transmitted.
3G models
3G RSSI
10
Green Off—Low signal strength (lower than -100 dBm).
On—High RSSI (-69 dBm or higher).
Slow Blinking—Low or medium RSSI (-99 to -90 dBm).
Fast Blinking—Medium RSSI (-89 to -70 dBm).
3G models
Amber On—No service. 3G models
3G GSM
11
Green On—Service is established.
Off—No service.
3G models
3G CDMA
12
Green On—Service is established.
Off—No service.
3G models
FXO Voice Green On—FXO port is connected.
Blinking—FXO port is either receiving or transmitting
data.
881
13
BRI Voice LNK Green On—BRI interface is connected.
BRI Voice B1 Green On—BRI B1 channel is connected.
Blinking—BRI B1 channel is either receiving or
transmitting data.
——
Table 1-45 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED Color Description 860 Series 880 Series 890 Series
1-138
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-46 describes the LEDs for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco
867VAE-K9 ISRs.
BRI Voice B2 Green On—BRI B2 channel is connected.
Blinking—BRI B2 channel is either receiving or
transmitting data.
——
FXS/DID Voice Green On—FXS/DID port is connected.
Blinking—FXS/DID port is either receiving or
transmitting data.
—SRST
models
V.92 Modem Green On—Modem is connected.
Blinking—V.92 port is either receiving or transmitting
data.
891
models
SFP
14
EN Off Not present. 892F
models
Green Present and enabled.
Amber Present with failure.
SFP S Green Blinking—Blinking frequency indicates port speed. 892F
models
1. SSID = service set identifier.
2. LWAPP = Lightweight Access Point Protocol.
3. PPP = Point-to-Point Protocol.
4. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital
subscriber line).
5. DSLAM = digital subscriber line access multiplexer.
6. ATM = Asynchronous Transfer Mode.
7. EFM = Ethernet in the First Mile.
8. 3G = Third-Generation.
9. WWAN = wireless WAN.
10. RSSI = Received Signal Strength Indicator.
11. GSM = Global System for Mobile Communication.
12. CDMA = code division multiple access.
13. SRST = Survivable Remote Site Telephony.
14. SFP = small-form-factor pluggable.
Table 1-45 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED Color Description 860 Series 880 Series 890 Series
1-139
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-46 LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs
LED Activity Description
Power/System Power/System LED: Solid
GE_MODE LED: Off
DSL_LINK LED: Off
Power is on and system running in the ROMMON mode.
Note During the early booting stage, both Power/System, GE_MODE, and
DSL_LINK LED will be turned on temporarily for the power on test.
DSL_LINK and GE_MODE LED will be turned off later after booting
into ROMMON.
Power/System LED: Solid
GE_MODE LED: Solid
DSL_LINK LED: Off
Cisco IOS functioning in GE WAN mode.
Power/System LED: Solid
GE_MODE LED: Off
DSL_LINK LED: Solid or
flashing
Cisco IOS functioning in DSL_WAN mode.
Note In Cisco IOS DSL_WAN mode, DSL_LINK LED will be solid after
DSL training complete or flashing during training.
xDSL
1
ACT
1. xDSL = General term referring to various forms of DSL, includi\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\
ng ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital subscriber line).
Green On—DSL interface is up.
Blinking—DSL WAN activity (traffic in either direction).
Faster blinking—Heavier traffic
Off—Device is powered off or the DSL WAN interface is down.
xDSL Link Green On—DSL WAN Mode is selected and DSL training complete.
Blinking—DSL WAN Mode is selected but incomplete DSL Link Up state,
such as in-training, or controller “OFF, or no cable attached to DSL connector.
Off—Device is powered off or GE WAN mode is selected.
GE ACT Green On—GE WAN interface is up.
Blinking—GE WAN activity (traffic in either direction).
Off—Device is powered off or GE WAN interface is down.
GE Mode Green On—GE WAN Mode is selected.
Off—Device is powered off or DSL WAN mode is selected.
1-140
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-47 describes the LEDs for the Cisco 892FSP.
Table 1-47LED desciption for Cisco 892FSP ISR, 896VA, 897VA, and 898EA Routers
Shared LEDs on the Cisco 881-V and Cisco 887VA-V Voice and Data Routers
On the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W routers, the BRI1, BRI2 and the FXS ports
share LED indicators. The following ports share an LED indicator:
BRI 1B1 channel and FXS 3
BRI 1B2 channel and FSX 4
BRI 2B1 channel and FXS 5
BRI 2 B2 channel and FXS 6
LED Color Activity Description
PWR_OK Green Power Status Off—No power.
Steady on—Normal operation.
Blink—Boot up phase or in ROM Monitor mode.
GE0 Green/Amber Link Status Green On—Ethernet port is connected.
Amber On—Fault with PoE. There is a fault with
the inline power supply.
Green/Amber Blinking—Data is either being
received or being transmitted.
Green/Amber Off—Ethernet port is not
connected.
GE1
GE2
GE3
GE4
GE5 Green Link Status On—Ethernet port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Ethernet port is not connected.
GE6
GE7
GE WAN ports Green Link Status On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—No link.
SFP WAN
ports
Green Link Status On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—No link.
VPN_OK Green Off—No tunnel.
Steady on—At least one tunnel is up.
PPP_OK Green Off—No PPP session.
Steady on—At least one PPP established.
1-141
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Because the LED indicators are shared, the LED illuminates (green) when either port is active. For
example, the LED indicator labeled BRI 1 B1 illuminates when either the BRI1 B1 channel is active or
when the FXS port is active. You can determine the activity status on each interface by using the
following commands.
For activity status on the FXS ports, use the show port summary command.
For activity status on the BRI ISDN port, use the show isdn status command.
Figure 1-85 shows a close-up view of the LED indicators.
Figure 1-85 Close-up of the BRI and FXS LED Indicators
Memory
The Cisco 860 series, 880 series, and 890 series routers contain flash memory and main memory.
Flash Memory
The Cisco 860 series, 880 series, and 890 series ISRs use non-upgradable flash memory storage. The
onboard flash memory contains the Cisco IOS software image, the boot flash contains the ROMMON
boot code, and a separate non-volatile flash contains the cookie configuration.
Table 1-48 describes the default flash memory storage.
300149
Table 1-48 Flash Memory Storage
Models Flash Memory Storage
Cisco 860 series and 880 series routers 128 MB
Cisco 880 series voice routers and Cisco 890 series routers 256 MB
Cisco 880 series routers with embedded WLAN antennas 256 MB
Cisco 860VAE routers 8 MB boot flash, 128 MB for IOS
Cisco 860VAE-K9 64 MB boot flash and IOS
1-142
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Note Flash memory is not upgradable. An external USB flash memory module may be used if additional flash
memory is needed.
Main Memory
Table 1-49 describes the main onboard memory storage for different router models.
USB Port
Table 1-50 describes the USB ports for different router models.
Table 1-49 Main Onboard Memory Storage
Models Onboard Memory Storage Expandability
Cisco 860 series routers 256 MB Not expandable.
Cisco 860VAE series routers 256 MB Not expandable.
Cisco 880 series routers 256 MB
(expandable to 768 MB)
A memory expansion slot accommodates
a PC2-4200, 256-MB or 512-MB double
data rate 2 (DDR2) SODIMM, for a
maximum of 768 MB.
Cisco 880 series routers with
embedded WLAN antennas
512 MB Not expandable.
Cisco 892FSP, 896VA,
897VA, 898EA routers
512 MB Expandable to 1 GB.
Table 1-50 USB Ports
Models USB
Cisco 860 series (non-VAE) No USB ports.
Cisco 860VAE series One USB 1.1-compliant port located on the back panel. The USB
port does not support eToken.
Cisco 860VAE-W-A-K9,
Cisco 860VAE-W-E-K9, and
Cisco
860VAE-POE-W-A-K9
series
For moe information, refer to the “Cisco 860VAE-W-A-K9, Cisco
860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 ISRs” section
on page 1-50.
Cisco 880 series One USB 1.1-compliant port located on the front panel. The USB
port provides connection for USB devices such as security tokens
and flash memory.
Cisco 890 series
1
1. Except for Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA.
Two USB 2.0-compliant ports located on the front panel.
Cisco 892FSP, Cisco 896VA,
Cisco897VA, Cisco 898EA
One USB 2.0-compliant port located on the back panel.
1-143
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Fan
Some router models do not have a fan, while other models have either one or two fans.
The fans spin at full speed, as a diagnostic aid, immediately after the router is powered up. After the
router has booted, the fans spin as fast as necessary to minimize fan noise while maintaining a safe
internal operating temperature.
The following models have no fan:
Cisco 892FSP
Cisco 896VA
Cisco 897VA
Cisco 898EA
Power Supply
The Cisco 892FSP has a single +12V power supply input. The Cisco 892FSP power connector is
different from the barrel-type connector on other 890 series models. The AC adapter cable connector has
four pins and a built-in locking mechanism. Figure 3-33 shows the power adapter connector.
The Cisco 896VA, 897VA, and Cisco 898EA use PoE (12 VDC 43 W, -54 VDC 80 W) and non-PoE
(12 VDC 60 W) power supplies.
Power over Ethernet Module
The Cisco 880 series ISRs can include an optional Power over Ethernet (PoE) module that provides
power to 802.3af-compliant devices connected to FE ports 0 and 1.
The Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant
devices connected to FE ports 0, 1, 2, and 3.
The PoE module is an option available only for the Cisco 880 series and 890 series ISRs and requires a
48 V external power adapter.
This function can be added to an 880 or 890 series router by installing the PoE adapter card in the router
and inserting the PoE 48 V external power adapter.
Note The Cisco 880 series ISRs with embedded WLAN antennas require a single external power supply: a
30 W power supply for non-POE-enabled routers or a 60 W power supply for POE-enabled routers. For
the back panels of some of these routers, see Figure 1-33 and Figure 1-35.
The following PoE budget is available:
C867VAE-POE-W-A-K9: 15.4 W (one port PoE)
Cisco 880 series: 30.8 W (2 ports each 15.4 W)
Cisco 890 series: 61.6 W (4 ports each 15.4 W)
1-144
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
3G Cellular Data WAN Connectivity
The 3G (Evolution Data Only [EVDO], Universal Mobile Telecommunications Systems [UMTS])
cellular interface is intended for use as a backup data link, but it can also be used as a primary WAN data
link. The 3G technology is third-generation wide-area cellular technology that is used in voice telephony
and broadband wireless data in a mobile environment.
Some Cisco 880G models come with a 34-mm express card slot ready for use with a commercial 3G card
radio. The 3G express card slot is located on the front panel. For a list of supported 3G cards, see the
Cisco 880 Series Integrated Services Routers Data Sheet.
Other Cisco 880G models come with embedded WAN modems for use over GSM or CDMA networks.
These routers have antenna connectors on the back panel. GSM routers have two SIM card slots. For
information on configuring Cisco 880 series ISRs for 3G, see Configuring Cisco EHWIC and 880G for
3G (EV-DO Rev A) and Configuring Cisco EHWIC and 880G for 3.7G (HSPA+)/3.5G (HSPA).
Wireless LAN Connectivity
The embedded Wi-Fi CERTIFIED™, 802.11a/b/g/n-compliant wireless AP is preinstalled in the router
as an optional feature. The Cisco 860 series routers support autonomous features and network
configurations. The Cisco 880 series and 890 series routers support both autonomous and unified
features and network configurations.
The wireless AP does not have an external Console port. Use the router’s Console port as described in
Chapter 3, “Connecting the Router. To configure the wireless device, use the Cisco IOS command-line
interface (CLI).
Table 1-51 describes the radios and antennas for the Cisco 860 series, 880 series, and 890 series routers.
Note Cisco 860VAE ISRs do not support wireless LAN connectivity.
The 5-GHz radio operates in the Unlicensed National Information Infrastructure (UNII) 1, 2, 3, 5-GHz
frequency bands.
Table 1-51 Wireless Device Radios and Antennas
Radio Module Platform Radio Band
Maximum Data
Throughput
1
Mode Antenna
Single-band
802.11b/g/n
draft 2.0 radio
module
Cisco 860 and 880 series
routers
Note Cisco 860VAE
ISRs do not
support wireless
LAN connectivity.
2.4 GHz Up to 100 Mb/s Cisco 860 series:
autonomous only
Cisco 880 series:
autonomous and
unified
Three captive,
omnidirectional dipole
antennas: 2 dBi at
2.4 GHz
1-145
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Supported Cisco Radio Antennas
The Cisco 891, Cisco 892, and Cisco 892F come with three removable dipole antennas that can be
replaced using the Cisco approved antenna extenders listed in Table 1-52.
Note Cisco supports only the antennas listed in Table 1-52 with the Cisco 890 series dual-band radio module.
Single-band
802.11b/g/n
radio module
Cisco 880 series routers
with embedded WLAN
antennas
2.4 GHz 100 Mb/s per radio,
up to 200 Mb/s
total
Autonomous and
unified
Three embedded,
omnidirectional
antennas: 2 dBi at
2.4 GHz
Dual-band
802.11a/n and
802.11b/g/n
radio modules
2.4 GHz
and
5 GHz
Three embedded,
dual-band,
omnidirectional
antennas: 2 dBi at
2.4 GHz and 5 dBi at
5 GHz
Dual-band
simultaneous
802.11a/n and
802.11b/g/n
radio modules
Cisco 890 2.4 GHz
and 5 GHz
100 Mb/s per radio,
up to 200 Mb/s
total
Autonomous and
unified
Three dual-band,
removable,
2.4-GHz/5-GHz
omnidirectional dipole
RP-TNC antenna
2
1. Actual data rate is highly dependent on your wireless environment.
2. The antennas require some minor installation. They must be screwed onto the RP-TNC antenna connectors on the I/O side of the chassis. See the following
document on Cisco.com for feature information: http://www.cisco.com/en/US/docs/routers/access/wireless/hardware/notes/antdip.html
Table 1-51 Wireless Device Radios and Antennas
Radio Module Platform Radio Band
Maximum Data
Throughput
1
Mode Antenna
Table 1-52 Cisco Antennas Supported on the Cisco 890 Series ISRs
Cisco Part Number Antenna Type Maximum Gain Description
AIR-ANTM2050D-R Omnidirectional 2.0 dBi at 2.4 GHz
5.0 dBi at 5 GHz
This is the default antenna. It is a swivel-mount
dipole dual-band blade antenna. For more
information, see Cisco Multiband Swivel-Mount
Dipole Antenna (AIR-ANTM2050D-R).
AIR-ANTM4050V-R Omnidirectional 4.0 dBi at 2.4 GHz
5.0 dBi at 5 GHz
Ceiling-mount dual-band antenna. This antenna
has a clip that allows it to be mounted on a
drop-ceiling cross member. For more information,
see Cisco Multiband Diversity Omnidirectional
Ceiling-Mount Antenna.
AIR_ANTM5560P-R Patch 5.5 dBi at 2.4 GHz
6.0 dBi at 5 GHz
Wall-mount dual-band antenna. For more
information, see Cisco Multiband Wall-Mount,
Corner-Mount, or Mast-Mount Antenna.
1-146
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Small Form-Factor Pluggable Port
The SFP port supports auto-media-detection, auto-failover, and remote fault indication (RFI), as
described in the IEEE 802.3ah specification.
See the Cisco 892F data sheet for a list of supported SFPs.
Feature Summary
Table 1-53 summarizes the hardware features available in the Cisco 860 series, Cisco 880 series, and
Cisco 890 series ISRs.
Table 1-53 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs
Feature Description 860 Series 880 Series 890 Series
Reset button Resets the router configuration to the factory default. All models All models All models
Resets the router configuration to customer configuration. 866VAE,
867VAE,
866VAE-K9,
867VAE-K9
——
FE
1
built-in
switch ports
Provides connection to 10/100BASE-T (10/100-Mb/s)
Fast Ethernet networks. The autosensing function in these
routers eliminates the need for a crossover cable and enables
the router to detect MDI
2
or MDIX
3
in any other PC or hub
with a straight-through cable or a crossover cable.
All models All models 891, 892,
892F
GE
4
built-in
switch port
Provides connection to 10/100/1000BASE-T
(10/100/1000-Mb/s) Gigabit Ethernet networks. The
autosensing function in these routers eliminates the need for
a crossover cable and enables the router to detect MDI
5
or
MDIX
6
in any other PC or hub with a straight-through cable
or a crossover cable.
866VAE-K9,
867VAE-K9
892FSP,
896VA,
897VA,
897VAB,
897VAM,
897VAW,
897VAMW,
898EA
Console or AUX
port
Provides a connection to the terminal or PC for software
configuration or troubleshooting. The Console port may be
configured as a virtual auxiliary port for dial backup and
remote management.
Cisco 891, Cisco 892, and Cisco 892F have separate console
and auxiliary ports.
Cisco 892FSP has combined console and auxiliary port.
All models All models All models
Security features Provides support for VPNs
7
, Cisco IOS Firewall, and
IPSec
8
. The Cisco 880 series routers also provide URL
filtering.
861, 867,
866VAE-K9,
867VAE-K9
All models All models
1-147
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Embedded
wireless AP
Provides Wi-Fi CERTIFIED™ 802.11a/b/g/n compliance.
The Cisco 860 series routers contain a single 802.11b/g/n
radio.
Some Cisco 880 series routers contain a single 802.11b/g/n
radio while others contain dual 802.11a/n and 802.11b/g/n
radios.
The Cisco 890 series routers contain dual 802.11b/g/n and
802.11a/n radios.
Wireless
models
802.11b/g/n
Wireless
models
802.11b/g/n
9
and
802.11a/n
10
Wireless
models
802.11b/g/n
and
802.11a/n
FE WAN port Provides connection to 10/100BASE-T. Can be connected to
other network devices, such as a cable modem, an xDSL
11
modem, or router. The router is capable of bridging and
multiprotocol routing between the LAN and WAN ports.
861 881 891, 892,
892F
GE WAN port 10/100/1000 GE WAN Port. 866VAE,
867VAE,
866VAE-K9,
867VAE-K9
All models
VDSLoPOTS
12
port
Provides connection to a VDSL network. 887V
ADSLoPOTS Provides ADSL connection over basic telephone service
with Annex A and Annex B ITU G. 992.1 (ADSL), G.992.3
(ADSL2), and G.992.5 (ADSL).
——
ADSLoISDN Provides ADSL connection over ISDN.
DSL Multi-mode
(VDSL and
ADSL2/2+)
Provides ADSL2/2+ or VDSL connection over POTS or
ISDN (ISDN on 886VA only).
866VAE,
867VAE,
866VAE-K9,
867VAE-K9
886VA,
887VA,887V
A-M
892FSP,
896VA,
897VA,
897VAB,
897VAM,
897VAW,
897VAMW,
898EA
Real-time clock
(RTC)
RTC provides nonvolatile date and time when the router is
powered on. The RTC is used for verifying the validity of the
Certification Authority stored on the router. It is backed up
by a nonreplaceable lithium battery.
866VAE,
867VAE,
866VAE-K9,
867VAE-K9
All models All models
Table 1-53 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
Feature Description 860 Series 880 Series 890 Series
1-148
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
USB port, Supports USB 1.1. Provides connection for USB devices
such as security tokens and flash memory.
The Cisco 880 series routers have a single USB port; the
Cisco 890 series routers have two USB ports.
Cisco 880 series routers with embedded WLAN antennas
have one USB 2.0 port.
Cisco 892FSP and Cisco 860VAE series routers have one
USB 2.0 port on the rear panel for temporary installation of
a Cisco-approved USB memory device for maintenance
purposes only. The port supports only USB 2.0. Refer to the
product datasheet for the list of supported USB flash
memory devices.
Note Cisco 860VAE series router USB port does not
support eToken.
866VAE,
867VAE,
866VAE-K9,
867VAE-K9
All models All models
PoE
13
(Optional) Provides power for 802.3af-compliant devices
(such as phones) that are connected to the router.
The Cisco 880 series routers support a 2-port PoE module;
the Cisco 890 series routers support a 4-port PoE module.
—Models with
PoE
Models with
PoE
G.SHDSL
14
port Provides 2-wire or 4-wire connection to a G.SHDSL
network.
888 898EA
3G
15
card slot Provides backup data link. 3G models
Dying gasp Detects when the router is losing power, and sends a
power-fail signal to warn the DSLAM
16
about the
impending line drop.
866VAE,
867VAE,
866VAE-K9,
867VAE-K9,
xDSL
models
888EA,
xDSL models
892FSP,
896VA,
897VA,
897VAB,
897VAM,
897VAW,
897VAMW,
898EA
Data BRI port Provides backup and remote management functions by
connecting to the ISDN service provider if the main VDSL
or G.SHDSL link fails.
—xDSL
models,
except for the
3G and
SRST
17
models
892,
897VAB
V.92 modem Provides dial backup and remote management functions if
the main WAN link fails.
891
FXO
18
port An FXO interface connects local calls to a central office or
PBX. This is the interface a standard telephone provides.
881 SRST
FXS
19
/DID
20
port
An FXS interface connects directly to a standard telephone,
fax machine, or similar device. This interface supplies
ringing voltage and dial tone to the station.
SRST models
Table 1-53 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
Feature Description 860 Series 880 Series 890 Series
1-149
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
BRI voice port The ISDN BRI S/T voice interface provides a client-side
(TE) ISDN S/T physical interface for connection to an NT1
device that terminates an ISDN telephone network.
887V
SFP
21
port Supports auto-media-detection, auto-failover, and remote
fault indication (RFI), as described in the IEEE 802.3ah
specification.
See the Cisco 892F data sheet for a list of supported SFPs.
892F
models,
892FSP,
896VA,
897VA,
897VAB,
897VAM,
897VAW,
897VAMW,
898EA
1. FE = Fast Ethernet.
2. MDI = media-dependent interface in normal mode.
3. MDIX = media-dependent interface in crossover mode.
4. GE = Gigabit Ethernet.
5. MDI = media-dependent interface in normal mode.
6. MDIX = media-dependent interface in crossover mode.
7. VPN = Virtual Private Network.
8. IPsec = IP security.
9. This applies to most models of the Cisco 880 series routers.
10. This applies to Cisco 880 series routers with embedded, wireless antennas.
11. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line), VDSL (very-high-data-rate digital
subscriber line), and G.SHDSL.
12. VDSLoPOTS = very-high-data-rate digital subscriber line 2 over plain old telephone service.
13. PoE = Power over Ethernet. This function can be added to an 880 or 890 series router by installing the PoE adapter card in the router and inserting the
PoE 48-V external power adapter.
14. G.SHDSL = (global industry standard) symmetrical high-speed DSL.
15. 3G = Third-Generation.
16. DSLAM = digital subscriber line access multiplexer.
17. SRST = Survivable Remote Site Telephony.
18. FXO = Foreign Exchange Office.
19. FXS = Foreign Exchange Station.
20. DID = Direct Inward Dialing.
21. SFP = small-form-factor pluggable.
Table 1-53 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
Feature Description 860 Series 880 Series 890 Series
1-150
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
CHAPTER
2-1
Cisco Integrated Services Router Hardware Installation Guide
2
Installing the Router
This chapter describes the equipment and the procedures for successfully installing the Cisco 860, 880,
890 ISRs, Cisco 819 ISRs, and the Cisco 812 ISRs, and contains the following sections:
Installing the Cisco 810 ISR, page 2-1
Installing the Cisco 860, 880, 890 ISR, page 2-43
Installing the Cisco 810 ISR
This section contains the following:
Installing the Cisco 812 ISR, page 2-1
Installing the Cisco 819 ISR, page 2-19
Installing the Cisco 812 ISR
This section describes the equipment and the procedures for successfully installing Cisco 812 ISR and
contains the following sections:
Items Shipped with your Router, page 2-2
Items Shipped with your PoE+ Splitter, page 2-2
Installing the Cisco PoE+ Splitter, page 2-2
Installing the SIM Card, page 2-6
Installing the 3G Antenna, page 2-8
Mounting the Cisco 812 ISR, page 2-9
Warning
Installation of the equipment must comply with local and national electrical codes.
Statement 1074
Warning
Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if
interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.
Avoid using such interconnection methods, unless the exposed metal parts are located within a
restricted access location and users and service people who are authorized within the restricted
access location are made aware of the hazard. A restricted access area can be accessed only through
the use of a special tool, lock and key or other means of security.
Statement 1072
2-2
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Items Shipped with your Router
Unpack the box and verify that all items listed on the invoice were shipped with the Cisco 812 ISR.
The following items are shipped with your router:
AC power adapter
Accessory kit 53-3453-01 which contains the following:
Pointer document 78-19961-01
RCSI document 78-17665-05
Mounting bracket kit C810-BR-CM
Includes screws needed for the installation
Two 3G Dipole antennas
Items Shipped with your PoE+ Splitter
Unpack the box and verify that all items listed on the invoice were shipped with the Cisco PoE+ splitter
(C810-POE-SPL).
The following items are shipped with your PoE+ splitter:
GE Cat5 cable
Power cable
Power cord lock
Screws needed for the installation
Shelf bracket
Note The above items are acceptable for use in Plenums and Air-handling spaces.
Installing the Cisco PoE+ Splitter
The PoE+ splitter (C810-POE-SPL) is an optional accessory that is intended to be mounted to the ceiling
tile rails (24 inches span) using the only supported box hanger available from a Cooper B-line BA50
distributor. The screws, cables, and power cord lock needed for the installation are included in the PoE+
splitter accessory kit. A 5 VDC power cable with 1.3 meters in length connects the 5 VDC output of the
PoE+ splitter to the router power input.
To install the Cisco PoE+ splitter, perform these steps:
Step 1 Secure the PoE+ splitter mounting plate into the rail from the BA50 with two 10-24 screws (see
Figure 2-1).
2-3
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-1 10-24 Screws
Step 2
Install the PoE+ splitter into the mounting plate with four 6-32 screws. (See Figure 2-2.)
285667
1
1
3
2
1 10-24 screws
2 Box hanger
3 Shelf bracket (PID 700-39491-01)
2-4
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-2 6-32 Screws
Step 3 Connect the supplied plenum rated Cat5 cable to the GE0 port on the PoE+ splitter.
Step 4 Connect the Cat5 cable from your PoE+ source to the PoE+ in port on the PoE+ splitter.
Step 5 Place the power cord lock onto the power cord behind the connector overmold as shown in Figure 2-3.
Slide the power cord lock forward so that it captures the overmold and is fully seated.
Figure 2-3 Placement of the Power Cord Lock onto the Power Cord
285668
1
2
3
4
1 6-32 screws 3 To PoE+ power source
2 Power cable with power cord lock installed 4 GE CAT5 cable
345076
1
2
1 Power cord connector
2 Power cord lock
2-5
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Step 6 Install the power cord with power cord lock to the power jack of the PoE+ splitter while making sure
that the two arms of the power cord lock slide into the corresponding slots on the PoE+ splitter and are
fully seated with both arms locking into the slots. Figure 2-4 shows the installation of the power cord
lock and other cables.
In the event that the power cord lock needs to be removed, user your thumb and index fingers to squeeze
the ends of the tabs while pulling away from the PoE+ splitter.
Figure 2-4 Installation of the Power Cord Lock and Other Cables
Step 7
Remove one ceiling tile to gain access.
Step 8 Install the pre-assembled rail with PoE+ splitter into the T-rail. Push down the box hanger mounting clips
to lock into the T-rail as shown in Figure 2-5.
345075
2-6
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-5 T-Rail
Installing the SIM Card
This section describes how to install and replace the SIM card. Ensure that the router is not mounted to
a wall, rack, or DIN rail.
Caution Do not touch any part of the exposed PCB circuit area when the SIM cover is removed.
Warning
Hot surface.
Statement 1079
To install the SIM card, perform these steps:
Step 1 Power off the router and disconnect the power cable from the power source.
Step 2 Place the router on a sturdy solid surface and orient the SIM access panel up to gain access. Ensure that
any installed antennas are oriented appropriately to avoid damage.
Step 3 Remove the SIM access panel being held in place by four 6-32 screws. (See Figure 2-6).
285669
To POE Power
Source
2-7
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-6 Accessing the SIM Card
Step 4 Remove the SIM card and install the new cards.
Step 5 Reinstall the same 6-32 flat head screws using a screw driver to secure the access panel back in place.
Figure 2-7 shows the SIM card installed and the SIM access panel closed.
344397
2-8
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-7 SIM Access Panel
Installing the 3G Antenna
Note Install the antenna before you mount the Cisco 812 ISR.
Warning
Do not locate the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, because they may cause serious injury or death. For
proper installation and grounding of the antenna, please refer to national and local codes (for
example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code,
Section 54).
Statement 1052
To install the 3G antennas to the router, perform these steps:
Step 1 Manually screw the antenna tight to the TNC connectors on the far left corner of the front panel.
Note It may be easier to straighten out the antenna before attaching it to the TNC connector and then bend it
back to the desired orientation once it is tight.
344398
2-9
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-8 Installing the 3G Antenna
Step 2
Orient the antenna perpendicular with respect to the floor. Figure 2-9 shows the 3G antenna installed.
Figure 2-9 3G Antenna Installed
Mounting the Cisco 812 ISR
This section describes the steps in mounting the Cisco 812 ISR in several configurations, including on
a suspended ceiling, on a hard ceiling or wall, and on an electrical or network box. This section contains
the following topics:
Mounting Hardware, page 2-10
344395
344396
2-10
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Mounting Bracket, page 2-10
Ceiling Grip Clips, page 2-11
Mounting the Cisco 812 ISR Below a Suspended Ceiling, page 2-13
Mounting the Cisco 812 ISR on a Hard Ceiling or a Wall, page 2-15
Mounting the Cisco 812 ISR to a Network or Electrical Box, page 2-17
Grounding the Cisco 812 ISR, page 2-18
Mounting Hardware
Mounting hardware for the Cisco 812 ISR consists of brackets, which connect to the bottom of the router,
and ceiling grid clips, which connect the bracket to a suspended ceiling. The bracket that you need
depends on the mounting location for the router. The ceiling grid clip that you need depends on the type
of suspended ceiling where you need to install the router. You do not need ceiling grid clips if you are
mounting the router to a hard-surface ceiling or a wall.
Mounting Bracket
The Cisco 812 ISR has only one mounting bracket. The C810-BR-CM universal bracket is versatile. It
works with electrical boxes, can be used for wall mounting, and adapts to ceiling installations.
Figure 2-10 shows the universal bracket installed on the Cisco 812 ISR.
2-11
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-10 Universal Bracket Installed on the Cisco 812 ISR
Ceiling Grip Clips
Use a ceiling grid clip to mount the router on a suspended ceiling. The ceiling grid clip that you need
depends on the ceiling tiles on your ceiling. There are two types of ceiling grid clips:
Ceiling Grid Clip, Recessed (AIR-AP-T-RAIL-R)—If your ceiling tiles hang below the ceiling grid,
this clip provides the best fit between the router and the ceiling.
Ceiling Grid Clip, Flush (AIR-AP-T-RAIL-F)—If your ceiling tiles are flush with the ceiling grid,
this clip provides a snug fit between the router and the ceiling.
The standard 9/16, 15/16, and 1 ½-inch wide T-rail mounting are supported with the Ceiling Grip Clips.
285644
1
1 Universal bracket
2-12
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-11 shows a ceiling grid clip.
Figure 2-11 Ceiling Grid Clip
Additional Adapters for Channel and Beam Ceiling Rails
The most common type of suspended ceiling support rail (the support for the ceiling tiles) is the ceiling
Tile rail or T-rail for short. You can attach a ceiling grid clip directly to a T-rail ceiling rail. However,
other types of ceiling rails, such as channel rails and beam rails, require an additional adapter clip
(AIR-CHNL-ADAPTER). You need two adapter clips for each router. Set screws on the clips hold them
securely on the ceiling rail.
Figure 2-12 shows the three types of ceiling rails: T-rail, channel, and beam. Figure 2-13 shows the
Cisco Access Point installed with mounting bracket, ceiling grid clip, and adapter clips.
121758
3
3
1
1
2
2
2
2
CEILING
GRID
WIDTH
382415
ABC
1-1/2 15/16 9/16
MM
INCH
CEILING
GRID
WIDTH
382415
ABC
1-1/2 15/16 9/16
MM
INCH
1 Locking screws 3 T-rail width detents (A, B, or C)
2 Bracket screw holes
2-13
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-12 T-Rail, Channel, and Beam Ceiling Rail Types
Figure 2-13 Adapter Clips Installed with Ceiling Grid Clips
Mounting the Cisco 812 ISR Below a Suspended Ceiling
The recommended power option for the Cisco 812 ISR, when mounted below a suspended ceiling, is the
Cisco C810-POE-SPL (PoE+ splitter) with the use of the supplied 1.3 meter power cable and Cat5 cable
(Plenum rated). The cables can be hidden above the suspended ceiling for a clean installation. See the
“Installing the Cisco PoE+ Splitter” section on page 2-2 for details on installing the PoE+ splitter.
Use a flat screwdriver if there is a need to remove the GE/console cables.
To mount the Cisco 812 ISR below a standard or recessed suspended ceiling, perform these steps.
Step 1 Decide where you want to mount the router on your suspended ceiling.
Step 2 Open the ceiling grid clip completely.
Step 3 Place the ceiling grid clip over the T-rail and close it to the appropriate detent (A, B, or C).
Step 4 Use a screwdriver to tighten the two ceiling grid clip locking screws to prevent the clip from sliding
along the T-rail.
Step 5 Observe the ceiling grid clip width detent letter (A, B, or C) that corresponds to the T-rail width.
Step 6 Align the corresponding holes (A, B, or C) on the mounting bracket over the mounting holes on the
ceiling grid clip.
281531
281532
Adapter clips
Ceiling grid
clip
Mounting
bracket
Access
point
2-14
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Step 7 Hold the mounting bracket and insert a 6-32 x 0.18-inch screw into each of the four corresponding holes
(A, B, or C) and tighten.
Step 8 If necessary, drill or cut a cable access hole in the ceiling tile large enough for the Ethernet and power
cables. Pull the cables through the access hole until you have about 1 foot of cable protruding from the
hole.
Step 9 (Optional). Use the ground screw to ground the router to a suitable building ground. See the “Grounding
the Cisco 812 ISR” section on page 2-18 for general grounding instructions.
Step 10 Connect the Ethernet and power cables to the router.
Step 11 Align the router feet over the keyhole mounting slots on the mounting bracket. If you created a hole for
the cables, make sure the router is positioned so that the cables reach their respective ports.
Step 12 Gently slide the router onto the mounting bracket until it clicks into place. Figure 2-14 shows the
Cisco 812 ISR mounted on a T-rail ceiling rail using a ceiling grid clip.
2-15
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-14 Suspended Ceiling Mounting Details
Mounting the Cisco 812 ISR on a Hard Ceiling or a Wall
This procedure describes the steps required to mount the Cisco 812 ISR on a ceiling constructed of
3/4-inch (19.05 mm) or thicker plywood using #8 fasteners using the universal mounting bracket
(C810-BR-CM).
Note The Cisco 812 ISR integrated antennas perform best when the router is mounted on horizontal surfaces
such as a table top or ceiling. For advanced features such as voice, location, and router detection, ceiling
mounting is strongly recommended. However, for smaller areas such as conference rooms, kiosks,
transportation environments, or hot-spot usage where data coverage is the primary concern, the unit may
be wall mounted using wall anchors or screws.
344533
1 27 8
4 3
65
1 To PoE+ power source 5 GE CAT5 cable to PoE+ splitter
2 Ceiling T-rail 6 Power and GE cable routed through a ceiling
mounting bracket and into the router so that the
cabling is hidden from directly below
3 Ceiling tile with opening cut for
cables
7 Ceiling grip clip
4 Power cable to PoE+ splitter 8 Ceiling mount bracket
2-16
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Note Wall mounting is only supported with the I/O (antenna) side facing up.
Step 1 Use the mounting bracket as a template to mark the locations of the mounting holes on the bracket.
Figure 2-15 shows details of the mounting bracket.
Caution Be sure to mark all four locations. To ensure a safe and secure installation, make sure you are using
adequate fasteners and mount the router using no less than four fasteners.
Caution Do not use plastic wall anchors for ceiling installations. When mounting the router on a hard ceiling, use
four fasteners capable of maintaining a minimum pullout force of 20 lbs (9 kg).
Figure 2-15 Universal Mounting Bracket Details
Step 2
Use a #29 drill (0.1360 inch [3.4772 mm]) bit to drill a pilot hole at the mounting hole locations you
marked.
Note The pilot hole size varies according to the material and thickness you are fastening. It is recommended
to test the material to determine the ideal hole size for your mounting application.
285646
1
1
1
1
2
2
2
2
1 Recommended wall mounting
screw holes
2 Mounting keyholes
2-17
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Step 3 (Optional) Drill or cut a cable access hole near and below the location of the mounting bracket cable
access cover large enough for the Ethernet cable, building ground wire, and power cables.
Step 4 Pull approximately 9 inches of cable through the hole.
Step 5 Route the Ethernet and power cables through the bracket before you attach the bracket to the ceiling or
wall.
Step 6 Route the cables through the main cable access hole and then through the smaller access hole as shown
in Figure 2-16.
Figure 2-16 Routing the Ethernet and Power Cables
Step 7 (Optional) Use the ground screw to attach the building ground wire to the ground location on the base
of the router. See the “Grounding the Cisco 812 ISR” section on page 2-18 for the general grounding
instructions.
Step 8 Position the mounting bracket mounting holes (with indents down) over the pilot holes.
Step 9 Insert a fastener into each mounting hole and tighten.
Step 10 Connect the Ethernet and power cables to the router.
Step 11 Align the router feet with the large part of the keyhole mounting slots on the mounting plate.
Step 12 Gently slide the router onto the mounting bracket keyhole slots until it clicks into place.
Mounting the Cisco 812 ISR to a Network or Electrical Box
To mount the Cisco 812 ISR to a network box or an electrical box, perform these steps:
Step 1 Position the universal mounting bracket (C810-BR-CM) over the existing network or electrical box and
align the bracket mounting holes with the box holes.
Step 2 Hold the mounting bracket in place and insert a 6-32 x 0.18-inch pan head screw into each of the
mounting holes and tighten.
Step 3 Pull approximately 9 inches of Ethernet and power cable through the hole.
344775
2-18
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Step 4 Route the cables through the bracket before you attach the bracket to the ceiling.
Step 5 Route the cables through the main cable access hole and then through the smaller access hole as shown
in Figure 2-16.
Step 6 (Optional) Use the ground screw to attach the building ground wire to the ground location on the base
of the router. See the “Grounding the Cisco 812 ISR” section on page 2-18 for the general grounding
instructions.
Step 7 Connect the Ethernet and power cables to the router.
Step 8 Align the router feet over the keyhole mounting slots on the optional mounting bracket.
Step 9 Slide the router onto the optional mounting bracket until it clicks into place.
Grounding the Cisco 812 ISR
Grounding is not always required for indoor installations because the Cisco 812 ISR is classified as a
low-voltage device and does not contain internal power supplies. However, it is recommended that you
check your local and national electrical codes to see if grounding is a requirement. If grounding is
required in your area or you wish to ground your router, perform the following steps:
Warning
Use copper conductors only.
Statement 1025
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.
Statement 1024
Warning
When installing or replacing the unit, the ground connection must always be made first and
disconnected last.
Statement 1046
Warning
This equipment needs to be grounded. Use a green and yellow 14 to 18 AWG ground wire to connect
the host to earth ground during normal use.
Statement 242
Step 1 Find a suitable building grounding point as close to the router as possible.
Step 2 Connect a user-supplied ground wire to the building grounding point. The wire should be a minimum of
#14AWG assuming a circuit length of 25 feet (30.5 cm). Consult your local electrical codes for
additional information.
Step 3 Route the ground wire to the router.
Step 4 Attach the wire to a suitable grounding ring lug.
Step 5 Crimp or solder the wire to the lug.
Step 6 Use a Phillips screwdriver to remove the existing 6-32 screw at the grounding location as shown in
Figure 2-17.
2-19
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-17 Connecting the Ring Lug onto the Grounding Point
Step 7 Connect the ring lug to the router grounding point and reinstall the same 6-32 screw.
Installing the Cisco 819 ISR
This section describes the equipment and the procedures for successfully installing the Cisco 819 ISR
and contains the following sections:
Equipment, Tools, and Connections, page 2-20
Installing the Router, page 2-22
Mounting the DC Power Supply, page 2-41
Note For compliance and safety information, see the Regulatory Compliance and Safety Information
Roadmap that ships with the router and the Regulatory Compliance and Safety Information for Cisco 800
Series Routers.
Warning
Read the installation instructions before connecting the system to the power source.
Statement 1004
1 2
302791
1 6-32 ground screw
2 Ground wire
2-20
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.
Statement 1024
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement
1030
Warning
No user-serviceable parts inside. Do not open.
Statement 1073
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning
Read the wall-mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people
and damage to the system.
Statement 378
Warning
The covers are an integral part of the safety design of the product. Do not operate the unit without the
covers installed.
Statement 1077
Warning
Do not locate the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, because they may cause serious injury or death. For
proper installation and grounding of the antenna, please refer to national and local codes (for
example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code,
Section 54).
Statement 1052
Warning
This product is not intended to be directly connected to the Cable Distribution System. Additional
regulatory compliance and legal requirements may apply for direct connection to the Cable
Distribution System. This product may connect to the Cable Distribution System ONLY through a
device that is approved for direct connection.
Statement 1078
Equipment, Tools, and Connections
This section describes the equipment, tools, and connections necessary for installing your Cisco 819
ISR. It contains the following topics:
Items Shipped with your Router, page 2-21
Additional Items, page 2-21
Connections, page 2-21
Ethernet Devices, page 2-21
2-21
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Items Shipped with your Router
Unpack the box and verify that all items listed on the invoice were shipped with the Cisco 819 ISR.
The following items are shipped with your router:
AC power supply (default)
AC power supply cable (default)
Cisco Configuration Professional (Cisco CP) CD
DC power supply (optional)
Power cord retention lock (available in Cisco 819HGW, Cisco 819HWD, Cisco 819HG-4G, and
Cisco 819G-4G ISRs only)
Power switch lock (available in Cisco 819HGW, Cisco 819HWD, and Cisco 819HG-4G ISRs only)
Straight-through RJ-45 Ethernet cable
Two cellular multiband swivel mount dipole antennas
Three WiFi antennas for Cisco 819HGW and Cisco 819HWD ISRs
Note AC or DC Power supply is included based on the your order.
Additional Items
The following items are not shipped with the router but are required for installation:
ESD-preventive cord and wrist strap.
Screws for mounting the router on a wall.
Two number-10 wood screws (round- or pan-head) with number-10 washers or two number-10
washer-head screws, for mounting on a wall stud. The screws must be long enough to penetrate at
least 3/4 inch (20 mm) into the supporting wood or metal wall stud.
Two number-10 wall anchors with washers, for mounting the router on a hollow wall.
Wire crimper for chassis grounding.
Wire for connecting the chassis to an earth ground.
AWG 14 (2 mm2) or larger wire for NEC-compliant chassis grounding.
AWG 18 (1 mm2) or larger wire for EN/IEC 60950–compliant chassis grounding.
Ring terminal with an inner diameter of 1/4 inch. (5 to 7 mm) for NEC-compliant chassis grounding.
Ring terminal used for grounding needs to be listed and suitable for 14 to 18AWG. Lock washer
needs to be added to ring terminal ground installation when not using power switch lock.
Ethernet cables for connecting to the Fast Ethernet (FE) WAN and LAN ports.
Connections
Obtain a broadband or Ethernet connection from your service provider.
Ethernet Devices
Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs.
Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports.
2-22
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
If you plan to configure the software using Cisco IOS commands through the console port, provide an
ASCII terminal or a PC that is running terminal emulation software to connect to the console port.
If you plan to connect a modem, provide the modem and modem cable.
Installing the Router
This section describes how to install the Cisco 819 ISR. These routers can be installed on a table top or
other flat horizontal surface mounted on a wall or DIN rail.
The recommended clearance when horizontally mounted is 1.5 inches on both sides for floor mount
bracket clearance and 2 inches on top. Top clearance is not required but stacking heat-dissipating objects
on top of the router is not allowed. I/O side clearance is needed as it is required to access the cable
connections. Clearance is not required on the backside (opposite side from I/O face) unless DIN rail
mounting is required. Clearance is required to attach and mount the DIN rail bracket. The same
clearances apply when mounted vertically.
This section also describes how to attach external antennas to the routers and contains the following
topics:
Warnings, page 2-22
Accessing the SIM Card, page 2-23
Installing Antennas, page 2-27
Installing a WiFi External Antenna, page 2-28
Installing on a Table, page 2-29
Mounting on a Wall, page 2-29
Installing a DIN Rail, page 2-30
Installing the Router Using the Configurable Low Profile DIN Mount, page 2-34
Installing the Power Cord Retention Lock, page 2-38
Installing the Power Switch Lock, page 2-39
Warnings
Warning
This equipment needs to be grounded. Use a green and yellow 14 to 18 AWG ground wire to connect
the host to earth ground during normal use.
Statement 242
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.
Statement 1024
Warning
Read the wall-mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people
and damage to the system.
Statement 378
2-23
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Warning
Do not cover or obstruct the router vents located on both sides of the router; otherwise, overheating
could occur and cause damage to the router.
Warning
Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not
stack routers on a desktop. Excessive weight on top of the router could damage the chassis.
Warning
Do not install the router or power supplies next to a heat source of any kind, including heating vents.
Warning
The intra-building port(s) of the equipment or subassembly is suitable for connection to intra-building
or unexposed wiring or cabling only. The intra-building port(s) of the equipment or subassembly
MUST NOT metallically connect to interfaces that connect to the OSP or its wiring. These interfaces
are designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in
GR-1089-CORE, Issue 5) and require isolation from the exposed OSP cabling. The addition of Primary
Protectors is not sufficient protection in order to connect these interfaces metallically to OSP wiring.
Warning
The intra-building port(s) (list the port or ports) of the equipment or subassembly must use shielded
intra-building cabling/wiring that is grounded at both ends.
Accessing the SIM Card
This section describes how to install and replace the SIM card. Ensure that the router is not mounted to
a wall, floor, or DIN rail.
Caution Do not touch any part of the exposed PCB circuit area when the SIM cover is removed.
Warning
Hot surface.
Statement 1079
To access the SIM card in the Cisco 819 ISR, follow these steps:
Step 1 Power off the router and disconnect the power cable from the power source.
Step 2 Place the router on its side and ensure that any installed antennas are carefully oriented.
Step 3 Remove the SIM access panel using four flat head #6 screws. (See Figure 2-18.)
2-24
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-18 Accessing the SIM Cards
Step 4
To open the SIM socket cover, slide the cover in the direction of the open arrow. (See Figure 2-19.)
Figure 2-19 Opening the SIM Socket Cover
Step 5
Gently lift the cover on its hinges. (See Figure 2-20.)
245829
364622
2-25
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-20 Lifting the Socket Cover
Step 6
Slide the SIM card into the slot in the cover. Gently push down the cover to close. The SIM card will
come in contact with the metal contacts in the socket. (See Figure 2-21.)
364623
2-26
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-21 Sliding the SIM Card into the Slot
Step 7
To lock the cover, slide it in the direction of the lock arrow. (See Figure 2-22.)
364624
2-27
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-22 Locking the SIM Socket Cover
Step 8
Replace the panel and the screws.
Installing Antennas
Note Before you install the Cisco 819 ISR on a table, wall, or DIN rail, install the antennas on the front panel.
It is difficult to install the antennas after the router is installed.
To attach the radio antennas to your wireless router, follow these steps:
Step 1 Manually screw the antenna tight to the TNC connectors on the back of the router. (See Figure 2-23.)
Figure 2-23 Installing the Antenna
Step 2
Orient the antennas. For optimum wireless performance, antennas should be generally perpendicular to
each other.
If the router is being mounted on a desk, orient the antennas straight up.
364626
245548
2-28
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Installing a WiFi External Antenna
This section describes how to install a WiFi external antenna.
Step 1 Install the lightning arrestor. For details in installing lightning arrestor, see Cisco Aironet Lightning
Arrestor (AIR-ACC245LA-R). The lightning arrestor for cellular(3G/4G/LTE) is CGR-LA-NM-NF or
CGR-LA-NF-NF. For detailed antenna information, see Table 1-13 and Table 1-15.
Step 2 Rotate the knurled portion of the WiFi external antenna clockwise to screw the antenna to the RP-TNC.
(See Figure 2-24.)
Note WiFi antennas should be generally perpendicular to each other to achieve best coverage.
Figure 2-24 Cisco WiFi Antenna Assembly
2
3
1
344030
1 3G/4G Dipole External Antenna 3 RP-TNC Connector
2 WiFi 2.4/5 Ghz Dipole External Antenna
2-29
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Installing on a Table
To install the router on a table or other flat horizontal surface, firmly place the router on a table or other
horizontal surface. Keep at least 1 inch (2.5 centimeters) of clear space for heat dissipation.
Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the
“Installing the Router Using the Configurable Low Profile DIN Mount” section on page 2-34.
Mounting on a Wall
The Cisco 819 ISR has mounting holes on the bottom of the chassis for mounting the unit on a wall or
other vertical surface.
Tip When choosing a location for wall-mounting the router, consider cable limitations and wall structure.
To mount the router on a wall, follow these steps:
Step 1 Remove the screws on the sides of the routers.
Step 2 Attach the standard brackets to the chassis using the three screws provided for each bracket. (See
Figure 2-25.)
Figure 2-25 Attaching the Standard Brackets
Step 3
Install the router to a wall stud using two number-10 wood screws, round- or pan-head, with number-10
washers or two number-10 washer-head screws. The screws must be long enough to penetrate at least 1.0
inch (25.4 mm) into the supporting wood or metal wall stud. (See Figure 2-26.) Tighten the screws to a
torque of 6 to 8 inch-pound.
Note The orientation of the Cisco 819 ISR products is critical when wall-mounting. The router must
be oriented as shown in Figure 2-26 with the left side of the router rotated up (as viewed from
the IO side) to comply with IP41 and safety criteria. No other wall mounting orientation is
supported.
282622
2-30
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Note The mounting brackets (PID number ACS-810-FWM) are not included in the package of C819G series
routers.
Figure 2-26 Installing the Router to the Wall
Note For hollow-wall mounting, each bracket requires two wall anchors with washers. Wall anchors and
washers must be size number 10.
Step 4 Route the cables so that they do not put a strain on the connectors or mounting hardware.
To comply with IP 41, cables should be routed down relative to the router to prevent water from
travelling on the cables.
Installing a DIN Rail
You can use either the 7.5-mm or the 15-mm thick DIN rail for the Cisco 819 ISR. Secure the DIN rail
to the mounting surface approximately every 7.8 inches (200 mm) and use end-anchors appropriately.
282623
2-31
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Note DIN rail mounting is not supported on Cisco 819GW, Cisco 819HGW, and Cisco 819HWD ISRs.
2-32
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
To attach the Cisco 819 ISR to a 35-mm wide DIN rail, follow these steps.
Step 1 Attach the DIN rail to the back of the router using the three screws provided. (See Figure 2-27.)
Figure 2-27 Attaching the DIN Rail to the Cisco 819 ISR
Step 2 Find the tab on the end of the DIN rail that extends past the router. (See Figure 2-28.) Press the tab in
and slide the DIN rail out while the tab is pressed down.
Figure 2-28 DIN Rail Tab
Step 3
Turn the router sideways so that the antenna is at the top.
Step 4 Position the rear edge of the router directly in front of the DIN rail, making sure that the DIN rail fits in
the space between the latch and hook.
Step 5 Position the router so that the hook on the DIN rail bracket hooks onto the top edge of the DIN rail. The
weight of the product can rest on the hook temporarily while the DIN rail bracket latches are secured.
Step 6 Push the DIN rail bracket latch up after the router is over the DIN rail to secure it. The router is now
installed in the DIN rail. (See Figure 2-29.)
282624
282625
2-33
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-29 Cisco 819 ISR Installed with the DIN Rail
282626
2-34
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Installing the Router Using the Configurable Low Profile DIN Mount
If space is limited between the DIN rail and the enclosure cover, the Configurable Low Profile DIN
Mount can be utilized to mount the router flat against the DIN rail. It can also be configured in three
different ways to allow router cabling to exit from the bottom, right or left.
Figure 2-30 Configurable Low Profile DIN Mount standard configuration
391198
2-35
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Configuring the Mount
Figure 2-31 Low Profile DIN Mount Configuration
The mount comes configured in a bottom cable exit position, with the rail latches in the slots marked
Bottom. To reconfigure the mount:
1. Remove the two DIN Rail Latch Bracket Screws (Item 2).
2. Slide the DIN Rail Latch Brackets (Item 5) and DIN Rail Latch (Item 6) against the spring pressure,
towards the edge of the tray and remove the bracket and latch assembly. Be careful not to lose the
springs.
3. Remove the DIN Rail Latch Springs (Item 4)
4. Identify the desired mounting configuration and replace the latch assemblies in slots with the
matching labels, using the reverse order of steps 1 through 3.
1 Mount tray 4 DIN Rail Latch Springs
2 DIN Rail Latch Bracket Screws 5 DIN Rail Brackets
3 Mount Serial Number 6 DIN Rail Latch
2
6
5
1
3
4
4
391199
2-36
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Attaching the mount to the router
Figure 2-32 Cisco ISR 819 mounted in a Configurable Low Profile DIN mount
To attach the router to the mount:
1. Remove the bottom screw of the 3 screws on the sides of the router at the front.
2. Slip the router into the mount tray
3. Align the holes at the front sides of the mount with the vacant screw holes on the router and
screw the mount to the router with the longer, 6-32 x .375 Philips/Pan Head screws with locking
washer (Cisco 48-0422-01), which are included with the kit.
4. Remove the screw near the middle on the back of the router
5. Locate the “L” bracket that came with the mount, and screw the bracket to the router with the
other 6-32 x .375 Philips/Pan Head screw and locking washer (Cisco 48-0422-01).
6. Now screw the bracket to the mount with the shorter, supplied, 6-32 x .25 Philips/Pan Head
screw and locking washer (Cisco 48-0421-01).
Attaching the Assembled Router and Configurable DIN Mount to the DIN Rail
Once the mount has been configured according to need, and the router has been attached to the mount,
the assembly is ready to be snapped onto the DIN rail.
391253
2-37
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Installing the Router Ground Connection
The router must be connected to a reliable earth ground. Install the ground wire in accordance with local
electrical safety standards.
For NEC-compliant grounding, use size 14 AWG (2 mm2) or larger copper wire and a ring terminal
with an inner diameter of 1/4 in. (5 to 7 mm).
For EN/IEC 60950-compliant grounding, use size 18 AWG (1 mm2) or larger copper wire.
Warning
This equipment needs to be grounded. Use a green and yellow 14 to 18 AWG ground wire to connect
the host to earth ground during normal use.
Statement 242
To install the ground connection, follow these steps:
Step 1 Strip one end of the ground wire to the length required for the terminal.
Step 2 Crimp the ground wire to the ring terminal using the wire crimper.
Step 3 If you choose to install the power switch lock, perform Step 5 to Step 7. Otherwise, perform Step 4,
Step 6 and Step 7.
Step 4 Attach the ring terminal to the chassis. Use the single screw provided. Tighten the screws to a torque of
8 to 10 inch-pound (0.9 to 1.1 newton meter). (See Figure 2-33.)
Figure 2-33 Chassis Ground Connection Using Ring Terminal
Step 5
Install the power switch lock, see the “Installing the Power Switch Lock” section on page 2-39. Tighten
the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m). Torque the hex standoff to the same torque.
Step 6 Connect the other end of the ground wire to a known reliable earth ground point at your site.
Step 7 If you are using this router in a vehicle, attach the ring terminal to the chassis using one of the screws
provided and the green or green and yellow striped wire. Connect the other end of the wire to the vehicle
ground.
1 Ring terminal
245828
1
2-38
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
After you install and properly ground the router, you can connect the power wiring, the LAN cables, and
the cables for administrative access as required for your installation.
Installing the Power Cord Retention Lock
The Cisco 819 ISRs have a power cord retention mechanism as an accessory. It locks the power cord to
the router so when a user accidentally pulls out the power cord, the power cord will not come out from
the router. For the complete list of Cisco 819 ISRs that support power cord retention lock, see Table 1-7.
This section describes how to install the power cord retention lock.
Step 1 Pre-assemble the o-ring onto the barrel of the power cord as shown in Figure 2-34.
Figure 2-34 Pre-assemble the O-Ring onto the Barrel
Step 2
Place the power cord lock onto the power cord behind the connector overmold as shown in Figure 2-35.
Slide the power cord lock forward so that it captures the overmold and is fully seated.
Figure 2-35 Place the Power Cord Lock onto the Power Cord
285515
1
2
3
1 O-ring 3 Power cord lock
2 Power cord connector
285516
1
2
1 O-ring 2 Power cord lock
2-39
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Step 3 Install the power cord with power cord lock and the pre-installed o-ring to mate with the power jack on
the router while making sure that the two arms of the power cord lock slide into the corresponding slots
on the router and are fully seated with both arms locking into the slots as shown in Figure 2-36.
Figure 2-36 Installing Power Cord Lock onto the Router
Step 4 To remove the power cord lock, use your thumb and index fingers to squeeze ends of tabs while pulling
away from the router. (See Figure 2-37.)
Figure 2-37 End of Tabs
Installing the Power Switch Lock
The Cisco 819 ISRs have a power switch lock as an accessory. The power switch lock prevents
unauthorized access to a tampered proof router (for example, router in a bus). For the complete list of
Cisco 819 ISRs that support power switch lock, see Table 1-7.
This section describes how to install the power switch lock.
Step 1 Install the power switch lock by following the parts listed in Figure 2-38.
All these parts are in the accessory kit in their own bag. The ring terminal does not have to be installed.
Figure 2-39 shows the power switch lock installed.
285517
285518
1
1 End of tabs
2-40
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-38 Installing Power Switch Lock
Figure 2-39 Power Switch Lock Installed
344033
1
2
3
4
5
1 Ring terminal 4 Power switch lock
2 Power switch lock washer 5 Pan-head screw
3 Power switch lock standoff
344034
2-41
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Mounting the DC Power Supply
Note This equipment is suitable for installation in Network Telecommunications Facilities and locations
where the NEC applies. This equipment is suitable for installations as part of the Common Bonding
Network (CBN).
Note The Battery Return (BR) input terminal shall be an isolated DC return (DC-I). The DC return terminal
or conductor shall not be connected to the equipment frame or the grounding means of the equipment.
DC-powered products have a nominal operating DC voltage of 24 and 48 VDC. Reference American
National Standard for Telecommunications (ATIS) 0600315.
Warning
Read the wall-mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people
and damage to the system.
Statement 378
The Cisco 800 ISR DC power supply may be mounted to a wall using four #6 pan- or round-head wood
screws for the mounting holes on the supply.
Caution Each mounting screw must go into a wall stud (wood) or a wall anchor of the appropriate type for the
wall. Screws into drywall is not sufficient to support the DC power supply.
For attaching to a wall stud, the power supply requires #6 wood screws (round- or pan-head). The
screws must be long enough to penetrate and tap at least 0.75 inches (19.1 mm) into the supporting
wood or metal wall stud.
For hollow-wall mounting, the power supply requires the use of appropriate-sized wall anchors that
work with the drywall thickness the unit is to be installed in. Use hollow-wall anchors that support
using #6 screws and use #6 pan- or round-head screws to secure the power supply to the wall. Each
wall anchor should be rated for at least 30 lbs.
Caution If the screws are not properly anchored, the strain of the DC supply cables could pull the router from the
wall.
2-42
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 810 ISR
Figure 2-40 DC Power Supply Wall-Mounting
To mount the DC power supply (PID: PWR2-20W-12VDC and Part Number: 341-0548-02) to the wall,
follow these instructions:
Step 1 Install the four screws into the mounting holes on the DC power supply (see Figure 2-40) before being
secured to the wall studs or wall anchors.
Step 2 Hang the DC power supply by securing the screws to the wall stud or into the wall anchors.
Note The DC supply is IP 41 compliant in all six orthogonal directions. The mounting orientation will
not affect IP 41 compliance.
Figure 2-41 DC Power Supply Wall-Mounting
To mount the DC power supply (PID: PWR2-22W-20-60 and Part Number: 341-100360-01) to the wall,
follow these instructions:
Step 1 Attach the four corner brackets to the DC power module using the screws provided for each bracket (see
Figure 2-41).
Step 2 Install the power module to a wall stud using the remaining screws provided for the brackets.
2.05
2.44
(2.95)
(1.97)
302465
(3.63)
4X (.48)
4X .17
366483
2-43
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Installing the Cisco 860, 880, 890 ISR
This section describes the equipment and the procedures for successfully installing the Cisco 860 series,
880 series, and 890 series ISRs, and contains the following sections:
Equipment, Tools, and Connections, page 2-44
Installing the Cisco 860, 880, and 890 Series Routers, page 2-45
Installing the C881G-B/S/V-K9 ISR, page 2-60
Installing the C881GW-S/V-A-K9 ISR, page 2-60
Installing the C881G-U-K9 ISR, page 2-60
Installing the Cisco 880G for 3.7G (HSPA+)/3.5G (HSPA) ISRs, page 2-62
Note For compliance and safety information, see the Regulatory Compliance and Safety Information
Roadmap that ships with the router and the Regulatory Compliance and Safety Information for Cisco 800
Series Routers.
Warning
All wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only
indoors.
Statement 372
Warning
Read the installation instructions before connecting the system to the power source.
Statement 1004
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning
Do not locate the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, because they may cause serious injury or death. For
proper installation and grounding of the antenna, please refer to national and local codes (for
example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code,
Section 54).
Statement 1052
Warning
No user-serviceable parts inside. Do not open.
Statement 1073
2-44
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Equipment, Tools, and Connections
This section describes the equipment, tools, and connections necessary for installing your Cisco 860
series, 880 series, and 890 series ISRs. It contains the following topics:
Items Shipped with your Router, page 2-44
Additional Items, page 2-44
Connections, page 2-45
Ethernet Devices, page 2-45
Items Shipped with your Router
Unpack the box and verify that all items listed on the invoice were shipped with the router.
Table 2-1 lists the items and their quantities that are shipped with each router model.
Additional Items
The following items are not shipped with the router but are required for installation:
ESD-preventive cord and wrist strap.
Screws for mounting the router on a wall:
Table 2-1 Items and Their Quantities That Are Shipped with the Cisco 860 Series, Cisco 880
Series, and Cisco 890 Series ISRs
Item
Cisco 860
Series
Routers
Cisco
860VAE
Series
Routers
1
1. By default, no cables are shipped with Cisco 860VAE models unless requested through the dynamic configuration tool.
Cisco 880
Series
Routers
Cisco 890
Series
Routers
Straight-through RJ-45 Ethernet cable (Default
and GREEN-OPTION)
————
ADSL RJ-11-to-RJ-11 straight-through cable———1
RJ-11 DSL
2
cable
2. DSL = digital subscriber line.
1
3
3. Shipped with Cisco 867 models only.
n/a 1
4
4. Shipped with Cisco 886, 887, 887M, and 886-J models only.
1
DSL RJ-45-to-dual-RJ-11 breakout cable n/a 1
5
5. Shipped with Cisco 888E models only.
1
RJ-45-to-DB-9 console cable ((Default and
GREEN-OPTION)
————
External 12 VDC power supply adapter 1111
AC power supply cable with cable retention clip1111
Cisco Configuration Professional (Cisco CP) CD
6
6. Cisco CP is optional by order and available only on some SKUs.
1111
2-45
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Two number-10 wood screws (round- or pan-head) with number-10 washers, or two number-10
washer-head screws, for mounting on a wall stud. The screws must be long enough to penetrate
at least 3/4 in. (20 mm) into the supporting wood or metal wall stud.
Two number-10 wall anchors with washers, for mounting the router on a hollow-wall.
Wire crimper for chassis grounding.
Wire for connecting the chassis to an earth ground:
AWG 14 (2 mm
2
) or larger wire for NEC-compliant chassis grounding.
AWG 18 (1 mm
2
) or larger wire for EN/IEC 60950–compliant chassis grounding.
Ring terminal with an inner diameter of 1/4 in. (5 to 7 mm), for NEC-compliant chassis grounding.
Ring terminal used for grounding needs to be listed and suitable for 14 to 18AWG. Lock washer
needs to be added to ring terminal ground installation when not using power switch lock.
Ethernet cables for connecting to the Fast Ethernet (FE) WAN and LAN ports.
Connections
Obtain a broadband or Ethernet connection from your service provider.
Ethernet Devices
Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs.
Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports.
If you plan to configure the software using Cisco IOS commands through the console port, provide
an ASCII terminal or a PC that is running terminal emulation software to connect to the console port.
If you plan to connect a modem, provide the modem and modem cable.
If you plan to use the Data BRI port, provide an NT1 device and an ISDN S/T cable.
If you plan to use the cable-lock feature, provide a Kensington or equivalent locking cable.
Installing the Cisco 860, 880, and 890 Series Routers
This section describes how to install the Cisco 860 series, 880 series, and 890 series ISRs. These routers
can either be installed on a table top, or other flat horizontal surface or be mounted on a wall. The
Cisco 890 series ISRs may be mounted in a rack. Certain Cisco 880 series ISRs can use the same
ACS-890-RM-19 rack mount kit. For compatibility, see the Cisco 800 Series Comparison Chart.
This section also describes how to attach WLAN antennas to the Cisco 890 series routers. This section
contains the following topics:
Warnings, page 2-46
Installing on a Table, page 2-46
Mounting on a Wall, page 2-47
Installing the Router Ground Connection, page 2-49
Installing the FIPS Cover, page 2-50
Installing Antennas for Cisco 890 Series, page 2-54
Installing Cisco 890 Series in a Rack, page 2-58
2-46
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Warnings
Warning
This equipment needs to be grounded. Use a green and yellow 14 to 18 AWG ground wire to connect
the host to earth ground during normal use.
Statement 242
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.
Statement 1024
Warning
Read the wall-mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people
and damage to the system.
Statement 378
Note Do not stack anything on top of the router.
Do not cover or obstruct the router vents located on both sides and top of the routers; otherwise,
overheating could occur and cause damage to the router.
Place router in ventilated area to avoid local air heating.
Caution Do not cover or obstruct the router vents located on both sides of the router; otherwise, overheating could
occur and cause damage to the router.
Caution Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not
stack routers on a desktop. Excessive weight on top of the router could damage the chassis.
Caution Do not install the router or power supplies next to a heat source of any kind, including heating vents.
Caution The top surface of the router is hot since heat is dissipated through the top. Do not keep any object in
direct contact with the surface for a prolonged period.
Installing on a Table
To install the router on a table or other flat horizontal surface, firmly place the router on a table or other
horizontal surface. Keep at least 1 inch (2.5 cm) of clear space beside the cooling inlet and exhaust vents.
Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the
“Installing Cisco 890 Series in a Rack” section on page 2-58.
2-47
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Note Do not place anything on top of the router.
Mounting on a Wall
The Cisco 860 series, 880 series, and 890 series ISRs have mounting holes on the bottom of the chassis
for mounting the unit on a wall or other vertical surface.
The mounting holes are bidirectional. You can hang the router with the front bezel facing upward or
downward.
Keep at least 1 inch (2.5 cm) of clear space beside the cooling inlet and exhaust vents.
Tip When choosing a location for wall-mounting the router, consider cable limitations and wall structure.
To mount the router on a wall, follow these steps:
Step 1 Determine the required distance between mounting holes on the router. Figure 2-42 shows the
wall-mount holes located on the underside of the router.
Note For most router models, the distance between mounting holes is 8.2 inches (208 mm), as shown
in Figure 2-42. For the Cisco 866 and Cisco 867 models, the distance is 7.85 inches (199 mm).
Verify the required distance before drilling the holes.
2-48
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Figure 2-42 Wall-mount Holes on the Underside of the Router
Step 2
Insert the screws, with anchors, into the wall. Leave 1/8 inch (0.32 cm) between the screw head and the
wall. See Figure 2-43.
Step 3 Hang the router on the screw without forcibly pushing towards the wall side. The screw head may
damage the protection wall inside. Place the power adapter on a nearby horizontal surface. See
Figure 2-43.
1 Wall-mount holes
231987
1
3.673 in.8.200 in.
5.961 in.
1
2-49
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Figure 2-43 Router Mounted on the Wall
Step 4
Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the
“Installing Cisco 890 Series in a Rack” section on page 2-58.
Installing the Router Ground Connection
The router must be connected to a reliable earth ground. Install the ground wire in accordance with local
electrical safety standards.
For NEC-compliant grounding, use size 14 AWG (2 mm
2
) or larger copper wire and a ring terminal
with an inner diameter of 1/4 in. (5 to 7 mm).
For EN/IEC 60950–compliant grounding, use size 18 AWG (1 mm
2
) or larger copper wire.
1 Two number-10 wood screws mounted on the
wall
3 Horizontal surface on which to place the
power adapter
2 Wall-mount holes 4 Distance between the screw head and the wall,
1/8 in. (0.32 cm)
231982
4
2
1
1
3
2-50
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
To install the ground connection, follow these steps:
Step 1 Strip one end of the ground wire to the length required for the ground lug or terminal.
Step 2 Crimp the ground wire to the ground lug or ring terminal, using the wire crimper.
Step 3 Attach the ground lug or ring terminal to the chassis, as shown in Figure 2-44. For a ground lug, use the
two provided screws with captive locking washers. For a ring terminal, use one of the screws provided.
Tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m).
Figure 2-44 Chassis Ground Connection Using Ring Terminal
Step 4
Connect the other end of the ground wire to a known reliable earth ground point at your site.
After you install and properly ground the router, you can connect the power wiring, the WAN and LAN
cables, and the cables for administrative access as required for your installation.
Installing the FIPS Cover
To install the FIPS cover in the router, perform these steps:
1 Ring terminal
231981
1
2-51
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Step 1 Remove the four mounting screws of the top cover.
284921
2-52
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Step 2 Install the left-side FIPS cover, as shown in detail A.
Step 3 Rotate and bring into the close position to hinge to the correct hexagon.
Step 4 Place the adapter plate before closing by aligning the mounting holes.
284922
Detail A
Adapter
Plate
2-53
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Step 5 Secure the FIPS cover with two mounting screws.
Step 6 Install the right-side FIPS cover the same way as the left-side FIPS cover.
Step 7 View after both covers are installed.
284923
284924
2-54
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Step 8 If the FIPS covers are installed with the rack mount brackets, the adapter plates are not required in the
installation.
Installing Antennas for Cisco 890 Series
The Cisco 890 series wireless routers have three reverse-polarity threaded Neill-Concelman (RP-TNC)
connectors on the back panel. The antennas that are shipped with the router are dual-band 2.4-GHz to
5-GHz omnidirectional dipole antennas.
Warning
All wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only
indoors.
Statement 372
Note Before you install the Cisco 890 series wireless router on a table, wall, or rack, connect the antennas to
the back panel. It is difficult to attach the antennas after the router is installed.
284925
2-55
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
To attach the radio antennas to your wireless router, follow these steps:
Step 1 Manually screw the antennas tight to the RP-TNC connectors on the back of the router.
Figure 2-45 Attaching Antennas to the Router
Step 2
Orient the antennas. For optimum wireless performance, the antennas should be perpendicular with
respect to the floor.
a. If the router is being mounted on a desk, orient the antennas straight up.
b. If the router is being mounted on a wall, orient the antennas perpendicular to the floor, as shown in
Figure 2-46 and Figure 2-47.
272486
2-56
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Figure 2-46 Antennas Oriented Vertically Up
274774
2-57
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Figure 2-47 Antennas Oriented Vertically Down
274775
2-58
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Installing Cisco 890 Series in a Rack
The Cisco 890 series ISRs can be mounted in a rack.
To install a Cisco 890 series ISR in a rack, follow these steps:
Step 1 Remove the screws, as shown in Figure 2-48.
Figure 2-48 Screw Locations
Step 2 Using the screws provided, attach the rack-mount brackets to the Cisco 890 series ISR chassis, as shown
in Figure 2-49. Use two screws on each side. Use a number 2 Phillips screwdriver to install the bracket
screws on both sides of the chassis.
Caution Do not over torque the screws. The recommended torque is 6 to 8 in-lb (0.7 to 0.9 N-m).
1 Screws
371427
1
1
1
2-59
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Figure 2-49 Attaching the Rack-mount Brackets to the Cisco 890 Series ISR
Caution Chassis installation must allow unrestricted airflow for chassis cooling.
Step 3 Using two screws for each side (supplied with the rack), attach the Cisco 890 series ISR with rack-mount
brackets to a 19-inch rack. Start with the lower pair of screws first, resting the brackets on the lower
screws while you insert the upper pair of screws.
Note Be sure to leave space above and below each unit in a rack to allow for cooling air circulation.
Note Do not stack equipment directly above the router. Keep at least 1 rack unit of space above the
router.
Tip The screw slots in the brackets are spaced to line up with every second pair of screw holes in the
rack. When the correct screw holes are used, the small threaded holes in the brackets line up with
unused screw holes in the rack. If the small holes do not line up with the rack holes, you must
raise or lower the brackets to the next rack hole.
Step 4 Place the power adapter on a nearby horizontal surface.
Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to
ensure your safety:
This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest
component at the bottom of the rack.
If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in
the rack.
Statement 1006
272484
2-60
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Step 5 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the
“Installing Cisco 890 Series in a Rack” section on page 2-58.
Installing the C881G-B/S/V-K9 ISR
To install the C881G-B/S/V-K9 ISR, follow the instructions in the “Installing the Cisco 860, 880, and
890 Series Routers” section on page 2-45.
However, the instructions for connecting the 3G card in the hardware installation guide do not apply to
the C881G-B/S/V-K9 ISR because it does not have a slot for adding a SIM card. These are
CDMA/EV-DO based routers and do not require a SIM card.
Installing Antennas
For instructions on installing the antennas for the Cisco 881 routers, please refer to the “Installing
Antennas” section on page 2-60.
Installing the C881GW-S/V-A-K9 ISR
To install the C881GW-S-A-K9 and C881GW-V-A-K9 ISRs, follow the instructions in the “Installing
the Cisco 860, 880, and 890 Series Routers” section on page 2-45 section.
However, the instructions for connecting the 3G card in the hardware installation guide do not apply
because these ISRs do not have a slot for adding a 3G card. Instead, a 3G modem is embedded in the
router.
Installing Antennas
For instructions on installing the antennas for the Cisco 881 routers, please refer to the “Installing
Antennas” section on page 2-60.
Installing the C881G-U-K9 ISR
To install the C881G-U-K9 ISR, follow the instructions in the “Installing the Cisco 860, 880, and 890
Series Routers” section on page 2-45.
However, the instructions for connecting the 3G card in the hardware installation guide do not apply to
the C881G-U-K9 ISR because it does not have a slot for adding a 3G card. Instead, a 3G modem is
embedded in the router.
Installing the SIM Cards
You can install one or two SIM cards into the C881G-U-K9 ISR. Installing two SIM cards lets you take
advantage of the Dual SIM feature, which provides a failover mechanism in case the primary SIM card
fails.
Figure 50 shows the SIM car installation steps.
2-61
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
Figure 50 SIM Card Installation
282316
1 2
3
A
B
4
A B
2-62
Cisco Integrated Services Router Hardware Installation Guide
Chapter 2 Installing the Router
Installing the Cisco 860, 880, 890 ISR
To install the SIM cards, follow these steps:
Step 1 Open the door covering the SIM card slots.
a. Insert the tip of the screw driver into the upper latch and gently disengage it as shown in the figure.
b. Remove the door as shown.
Step 2 To insert a SIM card into the SIM 0 slot, hold the SIM card with the contacts facing up as shown and
gently push the card into place until it locks in.
Step 3 To insert a SIM card into the SIM 1 slot, hold the SIM card with the contacts facing down as shown and
gently push the card into place until it locks in.
Step 4 Reattach the door.
a. Insert the doors bottom latches as shown.
b. Insert the doors upper latch into place as shown.
Installing the Cisco 880G for 3.7G (HSPA+)/3.5G (HSPA) ISRs
To install the C881G+7-K9, C886VAG+7-K9, C887VAG+7-K9, C887VAMG+7-K9, C888EG+7-K9,
C881GW+7-A-K9, C881GW+7-E-K9, C887VAGW+7-A-K9, and C887VAGW+7-E-K9 ISRs, follow
the instructions in the “Installing the Cisco 860, 880, and 890 Series Routers” section on page 2-45.
However, the instructions for connecting the 3G card in the hardware installation guide do not apply
because these ISRs do not have a slot for adding a 3G card. Instead, a 3G modem is embedded in the
router.
CHAPTER
3-1
Cisco Integrated Services Router Hardware Installation Guide
3
Connecting the Router
This chapter describes how to install the Cisco 860, 880, 890 ISRs and the Cisco 819 ISR.
Cisco 810 Series, page 3-1
Cisco 860, 880, 890 Series, page 3-8
Cisco 810 Series
Cisco 819 Series
This section describes how to connect Cisco 819 ISRs to Ethernet devices and a network. The section
contains the following topics:
Preparing to Connect the Router, page 3-1
Connecting a PC, Server, or Workstation, page 3-2
Connecting an External Ethernet Switch, page 3-3
Connecting a Terminal or PC to the Console Port, page 3-4
Connecting a Modem to the Console Port, page 3-5
Connecting the AC Adapter, page 3-5
Connecting the DC Adapter, page 3-6
Verifying Connections, page 3-7
Note For compliance and safety information, see the Regulatory Compliance and Safety Information
Roadmap that ships with the router and Regulatory Compliance and Safety Information for Cisco 800
Series Routers.
Preparing to Connect the Router
Before you connect the router to the devices, install the router according to the instructions in the
“Installing the Router” section on page 2-22.
3-2
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 810 Series
Preventing Damage to the Router
To prevent damage to your router, follow these guidelines when connecting devices to your router:
Turn off power to the devices and to the router until all connections are completed.
Caution Do not turn on the devices until after you have completed all connections to the router.
If you must supply your own cable, see the “Cisco 860, 880, 890 Series” section on page A-11 for
cabling specifications. If this appendix does not provide specifications for a particular cable, we
strongly recommend ordering the cable from Cisco.
Connecting a PC, Server, or Workstation
To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps:
Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. See Figure 3-1.
Figure 3-1 Connecting a Server, PC, or Workstation
Step 2
Connect the other end of the cable to the RJ-45 port on the network interface card (NIC) that is installed
in the PC, server, or workstation.
1 Yellow Ethernet cable 3 RJ-45 port on the network interface card
2 Ethernet switch port on the router
245583
3
2
1
3-3
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 810 Series
Step 3 (Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports.
Note Use the Cisco Configuration Express to configure the Internet connection settings. See
Cisco Configuration Professional Quick Start Guide for more information.
Connecting an External Ethernet Switch
If more than four PCs in an office must be connected to each other, you can add Ethernet connections to
the router by connecting an external Ethernet switch to the Ethernet switch on the router.
To connect an external Ethernet switch to an Ethernet switch port on the router, perform these steps:
Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. (See Figure 3-2.)
Figure 3-2 Connecting to an Ethernet Switch
Step 2 Connect the other end of the cable to the available port on the Ethernet switch to add additional Ethernet
connections.
Step 3 Turn on the Ethernet switch.
1 Ethernet switch port on the router 3 Yellow CAT5 Ethernet cable,
RJ-45–to–RJ-45, connecting to an external
Ethernet switch port
2 Available port on the external Ethernet switch
245585
MODE
Catalyst 3500
SERIES
XL
INLINE POWER
SYSTEM
1X
2X
15X
16X
RPS
STATUS
UTIL
DUPLX
SPEED
1
2
3
4
5
6
7
8
9
10
11
12
1
1X
2X
15X
16X
1
2
3
4
5
6
7
8
9
10
11
12
2
1
3
2
3-4
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 810 Series
Connecting a Terminal or PC to the Console Port
Connect a terminal or PC to the Console port either to configure the software by using the CLI or to
troubleshoot problems with the router.
To connect a terminal or PC to the console port on the router and access the CLI, follow these steps:
Step 1 Connect the RJ-45 end of a DB-9-to-RJ-45 serial cable to the RJ-45 Console port on the router.
Figure 3-3 shows the RJ-45 end of the serial cable connected to the Console port on the router.
Figure 3-3 Connecting a Terminal or PC to the Console Port
Step 2
Connect the DB-9 end of the DB-9-to-RJ-45 serial cable to the COM port on your laptop or PC.
Note Some laptops and PCs do not come with DB-9 serial port connectors and may require a
USB-to-serial port adapter.
Step 3 To communicate with the router, start a terminal emulator application.
For more information, see the Terminal Emulator Settings, page 3-16, and Applying Correct Terminal
Emulator Settings for Console Connections.
1 RJ-45 connector to the Console Aux port on
the router
2 DB-9 connector
245586
1
2
3-5
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 810 Series
Connecting a Modem to the Console Port
To connect a modem to the router, follow these steps:
Step 1 Connect the RJ-45 end of the adapter cable to the Console port on the router as shown in Figure 3-4.
Figure 3-4 Connecting a Modem to the Console Port
Step 2
Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter.
Step 3 Connect the DB-25 end of the modem adapter to the modem.
Step 4 Make sure that your modem and the router console port are configured for the same transmission speed
(up to 115200 b/s is supported) and support mode control with data carrier detect (DCD) and data
terminal ready (DTR).
Connecting the AC Adapter
Warning
The device is designed to work with TN power systems.
Statement 19
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: 120VAC, 20A U.S (240VAC, 16 to 20A international).
Statement 1005
Warning
This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations.
Statement 1045
245587
1
2
3
4
3-6
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 810 Series
To connect your Cisco 819 ISR to an AC power outlet, follow these steps:
Step 1 Connect the AC adapter to an AC power outlet.
Step 2 Plug the adapter cord into the router.
Connecting the DC Adapter
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than 36 VDC, 5A
Statement 1005
Warning
This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations.
Statement 1045
Warning
The device is designed to work with TN power systems.
Statement 19
To connect the DC power on your Cisco 819 ISR, follow these steps:
Step 1 Connect the black and white lead wires to a 12 VDC source.
The black lead is negative or ground and the white lead is positive. The output cable is 1.3 meters while
the input cable is 1 meter in length. (See Figure 3-5 and Figure 3-6.). For the complete list of supported
power adapters, see the “Supported Power Adapters” section on page A-9.
Figure 3-5 DC Power Supply PWR1-20W-12VDC and PWR1-20W-24VDC
302470
3
2
1
3-7
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 810 Series
Figure 3-6 DC Power Supply PWR2-20W-12VDC and PWR2-20W-24VDC
Step 2
Plug the adapter cord into the router.
Note The power adapters have 18 AWG wires for the input connection. Tinned bare wires are used for
the input connection as there is no standard established for connector type. Screw terminal
blocks are most often used.
Verifying Connections
To verify that all devices are properly connected to the router, first turn on all the connected devices,
then check the LEDs. To verify router operation, refer to Table 3-1.
For full LED description, see Table 1-45.
302438
3
2
1
1 Black wire (negative) 3 Adapter
2 White wire (positive)
Table 3-1 Verifying the Router Operation
Power and Link LEDs to Check Normal Patterns
SYS Yellow FPGA download is complete.
Green (blinking) ROMMON is operational.
Off After powering up, when FPGA is being downloaded (in
ROMMON).
3-8
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Cisco 860, 880, 890 Series
This section describes how to connect Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs to
Ethernet devices, Power over Ethernet (PoE), and a network.
Note Depending on the features available for your router, some content in this section may not apply to your
router.
The section contains the following topics:
Safety Warnings, page 3-9
Preparing to Connect the Router, page 3-1
Connecting a PC, Server, or Workstation, page 3-2
Connecting a Phone, page 3-13
Connecting an External Ethernet Switch, page 3-3
Connecting the V.92 modem Port, page 3-15
Connecting a Terminal or PC to the Console Port, page 3-4
Connecting a Modem to the Console Port, page 3-5
Connecting the 3G Card, page 3-18
Installing the 3G Adapter for Extended Cable/Antenna, page 3-24
Connecting a Data BRI Port, page 3-28
Connecting an FE Line to an FE WAN Port, page 3-30
Connecting a GE Line to an GE WAN Port, page 3-31
Connecting an xDSL Line, page 3-31
Connecting Power over Ethernet, page 3-34
Connecting the AC Adapter, page 3-5
Connecting an FXS Line, page 3-39
Connecting an FXO Line, page 3-40
Connecting a Voice ISDN BRI Line, page 3-42
Verifying Connections, page 3-7
Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap
that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series
Routers.
ACT Green Network activity on FE Switch ports, GE WAN port, 3G
cellular interface, and serial interfaces.
Off No network activity.
Table 3-1 Verifying the Router Operation (continued)
Power and Link LEDs to Check Normal Patterns
3-9
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Note The illustrations in this chapter show a wireless router with antennas attached. Non-wireless routers do
not have antennas or antenna connectors on the back panel. However, the procedures for connecting
devices to the router are the same for both wireless and non-wireless routers.
Safety Warnings
Warning
When installing the product, please use the provided or designated connection cables/power
cables/AC adaptors/batteries. Using any other cables/adaptors could cause a malfunction or a fire.
Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the
“UL” or “CSA” shown on the cord), not regulated with the subject law by showing “PSE” on the cord,
for any other electrical devices than products designated by CISCO.
Statement 371
Warning
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
Warning
This equipment has been designed for connection to TN and IT power systems.
Statement 1007
Warning
There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions.
Statement 1015
Warning
Take care when connecting units to the supply circuit so that wiring is not overloaded.
Statement 1018
Warning
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
Statement 1021
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first.
Statement 1026
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool.
Statement 1035
3-10
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Warning
Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
Statement 1036
Warning
Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Statement 1037
Warning
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning.
Statement 1038
Warning
To report a gas leak, do not use a telephone in the vicinity of the leak.
Statement 1039
Warning
Before opening the unit, disconnect the telephone-network cables to avoid contact with
telephone-network voltages.
Statement 1041
Warning
This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do
not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11
port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming
call.
Statement 1042
Warning
Do not locate the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, because they may cause serious injury or death. For
proper installation and grounding of the antenna, please refer to national and local codes (for
example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code,
Section 54).
Statement 1052
Warning
No user-serviceable parts inside. Do not open.
Statement 1073
Warning
Installation of the equipment must comply with local and national electrical codes.
Statement 1074
Preparing to Connect the Router
Before you connect the router to the devices, install the router according to the instructions in “Installing
the Cisco 860, 880, 890 ISR” section on page 2-43.
3-11
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Preventing Damage to the Router
To prevent damage to your router, follow these guidelines when connecting devices to your router:
Turn off power to the devices and to the router until all connections are completed.
Caution Do not turn on the devices until after you have completed all connections to the router.
Connect the color-coded cables supplied by Cisco to the color-coded ports on the back panel.
If you must supply your own cable, see “Cable Specifications” section on page A-28 for cabling
specifications. If this appendix does not provide specifications for a particular cable, we strongly
recommend ordering the cable from Cisco.
3-12
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Connecting a PC, Server, or Workstation
To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps:
Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router.
Figure 3-1 shows a Cisco 888W router connected to a PC.
Figure 3-7 Connecting a Server, PC, or Workstation
Step 2
Connect the other end of the cable to the RJ-45 port on the network interface card (NIC) that is installed
in the PC, server, or workstation.
Step 3 (Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports.
Note Use the Cisco Configuration Express to configure the Internet connection settings. See
Cisco Configuration Professional Quick Start Guide for more information.
1 Yellow Ethernet cable supplied with the router 3 RJ-45 port on the network interface card
2 Ethernet switch port on the router
3
2
231989
1
3-13
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Connecting a Phone
To connect an 802.3af-compliant phone to an Ethernet switch port, follow these steps:
Note A power source must be provided for the phone to function. This can be done in two ways: the phone
can be powered via the PoE function using the PoE enabled Ethernet ports, or by using an external AC
power source connected to the phone.
Step 1 Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router. Figure 3-8
shows a Cisco 888W router connected to a phone.
Figure 3-8 Connecting a Phone
1 Yellow Ethernet cable 3 RJ-45 port on a phone
2 Ethernet switch port 1 on the router
3
2
270551
1
12
ABC
3
DEF
45
JKLGHI
6
MNO
78
TUVPQRS
9
WXYZ
*
0
OPER
#
3-14
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Step 2 Connect the other end of the cable to the RJ-45 port on the phone.
Connecting an External Ethernet Switch
If more than four PCs in an office must be connected to each other, you can add Ethernet connections to
the router by connecting an external Ethernet switch to the Ethernet switch on the router.
To connect an external Ethernet switch to an Ethernet switch port on the router, perform these steps:
Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-2 shows
a Cisco 888W router connected to an Ethernet switch.
Figure 3-9 Connecting to an Ethernet Switch
Step 2
Connect the other end of the cable to the available port on the Ethernet switch to add additional Ethernet
connections.
Step 3 Turn on the Ethernet switch.
1 Ethernet switch port on the router 3 Yellow CAT5 Ethernet cable,
RJ-45–to–RJ-45, connecting to an external
Ethernet switch port
2 Available port on the external Ethernet switch
MO
DE
Catalyst 3500
SERIES
XL
INLINE POWER
SYST
EM
1
X
2
X
1
5
X
1
6
X
RP
S
STATU
S
UTIL
DU
PLX
SPEED
1
2
3
4
5
6
7
8
9
10
11
12
1
1
X
2
X
1
5
X
1
6
X
1
2
3
4
5
6
7
8
9
10
11
12
2
231986
1
3
2
3-15
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Connecting the V.92 modem Port
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first.
Statement 1026
To connect the router to your service provide network through the V.92 port, follow these steps:
Step 1 Connect one end of the straight-through R-J11 cable to the V.92 port.
Figure 3-10 shows how to connect the router to the service provide through the V.92 port.
Figure 3-10 Connecting to Your Service Provider Through the V.92 port
Step 2
Connect the other end of the straight through R-J11 cable to an RJ-11 telephone wall outlet.
1 V.92 port on the router 2 Telephone wall outlet
272387
1
2
3-16
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Connecting a Terminal or PC to the Console Port
Connect a terminal or PC to the Console Auxiliary (Aux) port either to configure the software by using
the CLI or to troubleshoot problems with the router.
To connect a terminal or PC to the console port on the router and access the CLI, follow these steps:
Step 1 Connect the RJ-45 end of a DB-9–to–RJ-45 serial cable to the RJ-45 Console Aux port on the router.
Figure 3-3 shows the RJ-45 end of the serial cable connected to the Console Aux port on the router.
Figure 3-11 Connecting a Terminal or PC to the Console Port
Step 2
Connect the DB-9 end of the DB-9–to–RJ-45 serial cable to the to the COM port on your laptop or PC.
Note Some laptops and PCs do not come with DB-9 serial port connectors and may require a
USB-to-serial port adapter.
Step 3 To communicate with the router, start a terminal emulator application.
Terminal Emulator Settings
Use the following settings for the terminal emulator connection:
9600 baud
8 data bits, no parity
1 stop bit
No flow control
1 RJ-45 connector to the Console Aux port on
the router
2 DB-9 connector
2
1
231990
3-17
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
When the terminal emulator establishes communications, the router prompt is displayed.
For more information on terminal emulation settings, see Applying Correct Terminal Emulator Settings
for Console Connections.
Connecting a Modem to the Auxiliary Port
To connect a modem to the router, follow these steps:
Step 1 Connect the RJ-45 end of the adapter cable to the Aux port on the router as shown in Figure 3-4.
Figure 3-12 Connecting a Modem to the Aux Port
Step 2
Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter.
Step 3 Connect the DB-25 end of the modem adapter to the modem.
Step 4 Make sure that your modem and the router auxiliary port are configured for the same transmission speed
(up to 115200 bits per second [b/s] is supported) and support mode control with data carrier detect
(DCD) and data terminal ready (DTR).
1 Aux port (RJ-45) 3 DB-9 to DB-25 modem adapter (if required)
2 Light blue console cable 4 Modem
272386
1
2
3
4
3-18
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Connecting the 3G Card
Note For information on embedded multiband, multiservice WAN modems, see Configuring Cisco EHWIC
and 880G for 3G (EV-DO Rev A) and Configuring Cisco EHWIC and 880G for 3.7G (HSPA+)/3.5G
(HSPA).
Note The Cisco 880G router does not support online insertion and removal (OIR) of the 3G card. You must
enter the shutdown command on the cellular interface before you remove the 3G card from the router.
To connect and secure the 3G card, follow these steps:
Step 1 Align the 3G card to the 3G express card slot, as shown in Figure 3-13. Keep the card parallel to the
surface and firmly push the card into the slot.
Tip Holding the 3G card on the flat metal surface makes it easier to align and insert the 3G card.
Note When inserting the card into the 3G express card slot, you may hear a metal-on-metal sound as
the 3G card rubs against the internal metal cage. The 3G card is designed to fit tightly into the
3G express card slot. Firm pressure may be required to insert the card.
Note Global System for Mobile Communications (GSM) customers need to insert a SIM card,
provided by their network carrier, into the 3G card.
3-19
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Figure 3-13 Inserting the 3G Card
Step 2
Open the top of the anti-theft locking bracket, as shown in Figure 3-14.
Figure 3-14 Opening the Anti-theft Locking Bracket
1 3G card with the Cisco logo facing up 4 Screw holes for locking bracket
2 3G express card slot 5 Pin holes for aligning the locking bracket
3 Notches on the 3G card 6 SIM slot (in HSPA
1
cards only)
1. HSPA = High-Speed Packet Access.
271473
1
6
2
5
4
5
3
3
1 Pins on the locking bracket for alignment
271474
Front View Back View
1
1
3-20
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Step 3 Slide the opened locking bracket under the 3G card. The locking bracket should align with the notches
on either side of the 3G card, as shown in Figure 3-15, and the pins on the locking bracket should be
inserted into the corresponding holes in the router.
Figure 3-15 Installing the Locking Bracket
1 3G card 3 Notch on the 3G card
2 Locking bracket
1
2
3
271726
3-21
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Step 4 Close the locking bracket, as shown in Figure 3-16.
Figure 3-16 Closing the Locking Bracket
Step 5
Insert the screws, as shown in Figure 3-17, and tighten with a number 2 Phillips screwdriver.
Figure 3-17 Inserting the Screws
Step 6 To connect the antenna to the 3G card, insert the antenna connector into the antenna connector receptacle
on the 3G card.
1 3G card 2 Locking bracket
1
2
271580
1 3G card 3 Screws
2 Locking bracket 4 Screw holes on the locking bracket
271476
3
4
2
1
4
3-22
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Note The antenna connector receptacle may be located on the left, right, or front of the 3G card, depending
on your card.
Figure 3-18 and Figure 3-19 show the antenna connected to the 3G card with an SSMB type plug, and
the antenna with the SMK-TS-9 connector.
Figure 3-18 Antenna connected to the 3G Card with SSMB connector
1 Antenna on a cradle 3 Antenna connector receptacle
1
1. The antenna connector receptacle is located on either the left, right or front of the card for different SKUs. Please locate the
receptacle of your card before plugging in the cable.
2 Antenna SSMB connector
272653
1
2
3
3-23
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Figure 3-19 Antenna with the SMK-TS- 9 Connector
If you are using an extension cable, you must attach the 3G adapter for extended cable antenna to the
body of the router. Depending on the SKU ordered, the adapters come with different connectors.
Table 3-2 lists the different adapters and SKUs supported by each adapter. For instructions on how to
install the adapter, see the “Installing the 3G Adapter for Extended Cable/Antenna” section on
page 3-24. Otherwise, follow Step 7.
Step 7 Clean the flat surface to which you will affix the antenna.
279085
Original
antenna assembly
SMK-TS-9
connector
Cable
Table 3-2 3G Adapters and Supported SKUs
3G Adapter SKU Description SKUs Supported
3G-ACC-SMKTS9-TNC 3G adapter for extended cable/antenna
with an SMK-TS-9 to TNC connector.
Use this with the pentaband dipole
indoor antenna
(3G-ANTM-SMKTS9).
PCEX-3G-HSPA-R6,
CISCO881G-G-K9
3G-ACC-SSMB-TNC 3G adapter for extended cable/antenna
with an SSMB to TNC connector. Use
this with the pentaband dipole indoor
antenna shipped with your product.
PCEX-3G-HSPA,
PCEX-3G-HSPA-A,
PCEX-3G-CDMA-S,
PCEX-3G-CDMA-V,
PCEX-3G-CDMA-B,
CISCO881G-A-K9,
CISCO881G-S-K9,
CISCO881G-V-K9
3-24
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Step 8 Remove the protective tape from the adhesive on the bottom of the antenna cradle, then firmly press the
cradle to the flat surface.
Installing the 3G Adapter for Extended Cable/Antenna
For better signal and reception, if you are using the Cisco 3G Adapter for Extended Cable/Antenna,
3G-ACC-SMKTS9-TNC, follow these steps to install it:
Step 1 Locate and remove the Phillips screw on the left side of the router as shown in Figure 3-20. Keep the
screw aside for Step 4.
Figure 3-20 Locating the Phillips Screw
1 Phillips screw on the left side of router 2 Air vent holes to be aligned with adapter
279124
2
2
1
3-25
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Step 2 Locate the hooks on the adapter as shown in Figure 3-21.
Figure 3-21 Locating the Hooks on the Adapter
Step 3
Align and insert the hooks of the adapter into the air vent holes on the left side router body as shown in
Figure 3-22.
Figure 3-22 Inserting the Hooks
279122
1
1 Hooks on the adapter
279123
1
1
1 Hooks aligned and inserted into the router.
3-26
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Step 4 Align the circular adapter hole with the hole on the router chassis from where you removed the screw in
Step 1 and use the screw to attach the adapter to the router as shown in Figure 3-23.
Figure 3-23 Attaching the Adapter
279091
3-27
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Step 5 Connect the extension cable to the 3G card, as described in the “Connecting the 3G Card” section on
page 3-18. The complete assembly is shown in Figure 3-24.
Figure 3-24 Adapter Connected to 3G Card and Router Chassis
Now the adapter is ready for use with the extension cable.
Table 3-3 lists the loss information for the ultra-low-loss (ULL) LMR 400 cables available with the
adapter for the 3G fixed platforms.
1 Router chassis 4 SSMB or SMK-TS-9 connector
2 3G adapter for extended cable/antenna 5 3G card inserted into the router
3 Cable 6 3G card
279089
3
2
1
6
5
4
3-28
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Note Antenna orientation can increase or decrease signal reception due to polarization. Typically, an SP’s
transmitting antenna on the BTS is a vertically polarized omnidirectional antenna, which means the
electromagnetic waves are transmitted from it in a vertical plane. Hence, the receiving antenna needs to
be vertically oriented too in order to receive the best signal. As the angle of the antenna orientation is
changed from vertical to horizontal, only an angular component of the signal is picked up by the antenna.
Therefore, if the antenna orientation is horizontal, the antenna picks up the least signal. The signal is
received by the antenna as a result of it bouncing off of reflective surfaces. Hence, depending on where
the antenna is placed, it may receive different signal strengths. However, the recommended position is
vertical.
For additional information on all the available cables and antennas available for 3G, go to:
http://www.cisco.com/en/US/docs/routers/access/1800/1861/software/feature/guide/mrwlsgsm.html#w
p1262730
Connecting a Data BRI Port
You can connect the Data BRI port to the ISDN service provider as a backup link to the WAN port in
case the primary xDSL (general term referring to various forms of DSL, including global industry
standard symmetrical high-speed DSL [G.SHDSL]) WAN service fails. The Data BRI connection is not
available on the third-generation (3G) models.
The cabling requirements for the ISDN S/T connection are as follows:
You must provide two unshielded Category 5 cables. The first cable connects the NT1 box to the
splitter, and the second cable connects the splitter to the wall jack.
There are RJ-45 connectors at both ends of the default orange ISDN S/T cable. However, an
RJ-45–to–RJ-11 ISDN S/T cable is available upon request if the wall jack at the site requires an
RJ-11 connector. Contact your router reseller for the appropriate cable.
Caution Both LAN and WAN ports use RJ-45 connectors. Use caution when connecting cables to these
connectors. To avoid damage to the router, do not connect telephone-network voltage (TNV) circuits
(such as ISDN or DSL circuits) to safety extra-low voltage (SELV) circuits (such as LAN circuits).
Table 3-3 Cisco Adapter Cables for Use with 3G Fixed Routers
Cisco Product Number
Antenna Adapter
Length Insertion Loss Frequency (MHz)
3G-ACC-SSMB-TNC 14.5 inches 0.66 dB 2100
3G-ACC-TS9-TNC 13.5 inches 0.62 dB 2100
3-29
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
To connect the Data BRI port to the ISDN service provider, follow these steps:
Note Although the following procedure shows a Cisco 888W data router, this procedure applies to all
Cisco 880 series router with a Data BRI port.
Step 1 Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-25 shows a
Data BRI connection.
Figure 3-25 Connecting the Data BRI Port to the ISDN Line
Step 2 Connect the other end of the orange ISDN S/T cable to the S/T port on the NT1 box.
Step 3 Connect the first unshielded CAT 5 cable from the U-port on the NT1 box to the telephone line port on
the splitter.
1 Data BRI port on the router 6 U-port on the NT1 box
2 ISDN S/T cable 7 xDSL splitter (provided by the xDSL service
provider)
3 Network termination 1 (NT1) box 8 Telephone line port on the splitter
4 S/T port on the NT1 box 9 Telecommunication service port on the
splitter
5 Unshielded CAT 5 cable 10 Wall jack
231991
3
1
4
2
10
6
9
8
7
5
5
3-30
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Step 4 Connect the second unshielded Category 5 cable from the telecommunication service port on the splitter
to the wall jack to allow a link to the network service provider.
Connecting an FE Line to an FE WAN Port
To connect the Fast Ethernet (FE) WAN port on the router, follow these steps:
Step 1 Connect one end of the yellow cable to the FE WAN port as shown in Figure 3-26.
Figure 3-26 Connecting the FE WAN Port
Step 2
Connect the other end of cable to an available port on the modem.
1 FE WAN port 3 Modem connected to the Internet
2 CAT 5 cable
WAN
FE 4
1
Internet
Internet
Internet
2
3
231992
1
3-31
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Connecting a GE Line to an GE WAN Port
To connect the Gigabit Ethernet (GE) WAN port on the router, follow these steps:
Step 1 Connect one end of the yellow cable to the GE WAN port as shown in Figure 3-27.
Figure 3-27 Connecting the GE WAN Port
Step 2 Connect the other end of cable to an available port on the modem.
Connecting an xDSL Line
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first.
Statement 1026
1 GE WAN port 3 Modem connected to the Internet
2 CAT 5 cable
Internet
Internet
Internet
2
3
274493
1
3-32
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Caution Cisco Systems DSL WAN Interfaces are tested for compliance with regulatory standards such as FCC
Part 68, ITU-T K.21, IEC 61000-4-5, and CSA/EN/IEC/UL 60950-1. These standards assume Primary
Protection devices protect the Customer Premise Equipment (CPE). These devices are normally installed
by the service provider, local exchange carrier or qualified service person and are located at the telecom
service provider entrance, network interface box, or demarcation point. See Figure 3-28 for the likely
location of the primary protection device. The primary protection device must be suitable for the xDSL
interface employed. Please contact your sales team or qualified service person for further information
and installation.
Caution To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL Listed or CSA Certified
Telecommunication Line Cord.
Warning
Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool.
Statement 1035
Warning
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning.
Statement 1038
Warning
To report a gas leak, do not use a telephone in the vicinity of the leak.
Statement 1039
Warning
There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions.
Statement 1015
3-33
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Figure 3-28 Primary Protection Device Location
To connect the router to a global industry standard symmetrical high-speed DSL (G.SHDSL) line,
very-high-speed digital subscriber line 2 (VDSL2) port, or an ADSL2+ line, follow these steps:
Step 1 Connect one end of an RJ-11 (RJ-45 on 880 E models) cable to the port on the router. See Figure 3-29.
Figure 3-29 Connecting the xDSL Line
Step 2
Connect the other end of the cable to the DSL wall jack.
Router
Home or Business
Service Utilities Entrance
or Demarcation Point
Network Interface Box/
Network Interface Device/
Station Protector
Building Ground Rod connected to
Service entrance and Primary Protection
* Alternative Underground Service Entrance
Note: Primary Protection
may be located Outside
or Inside of Premise
Telecom Service
Overhead Service
Entrance
281392
1 G.SHDSL port, VDSL2oPOTs port, or
ADSL2+ port
2 DSL wall jack
232175
2
1
3-34
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Caution The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN port may
occur if a non-RJ-45 connector is inserted.
Note The DSL line must be provisioned by your service provider and correctly configured so that the LED
shows the carrier detect (CD) status. On Cisco 860VAE routers, check the DSL Link LED.
Connecting Power over Ethernet
Warning
This unit might have more than one power supply connection. All connections must be removed to
de-energize the unit.
Statement 1028
Warning
This product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source
or an IEC60950 compliant limited power source.
Statement 353
Figure 3-30 shows how to connect the 48-VDC Power over Ethernet (PoE) power adapter to your router.
The PoE adapter provides power to ports 0 and 1 of the 4-port 10/100 FE switch on the Cisco 880 series
routers and ports 0,1, 2, and 3 of the 8-port 10/100 FE switch on the Cisco 890 series routers.
Note The router must also be connected to an AC power outlet through a 12-VDC adapter. To connect the
router to an AC outlet, see the“Connecting the AC Adapter” section on page 3-5.
Note Be sure that the internal PoE is enabled for this connection procedure to work.
3-35
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Figure 3-30 Connecting PoE for the Cisco 880 and the Cisco 890 Series Routers
The Cisco 880 series ISRs with embedded WLAN antennas require a single external power supply: a
30-W power supply for non-POE-enabled routers or a 60-W power supply for POE-enabled routers. For
the back panels of some of these routers, see Figure 1-33 and Figure 1-35.
Connecting the AC Adapter
Warning
The device is designed to work with TN power systems.
Statement 19
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than:
120 VAC, 20 A U.S. (240 VAC, 16 to 20 A international).
Statement 1005
Warning
This unit might have more than one power supply connection. All connections must be removed to
de-energize the unit.
Statement 1028
Note The Cisco 892FSP utilizes a single 4-pin power connector type. Figure 3-33 shows the pin number
assignment of the Cisco 892FSP Power Adapter Connector.
1 48-VDC PoE input jack 4 AC plug
2 Power cord 5 12-VDC input power-jack plug
3 Power adapter—48 VDC 6 Power adapter—12 VDC
231995
5
22
6
4
4
3
1
3-36
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
To connect your Cisco 860 series, Cisco 880 series, or the Cisco 890FSP ISR to an AC power outlet,
follow these steps:
Step 1 Connect the router to an AC power outlet as shown in Figure 3-31.
To connect the AC power outlet for the Cisco 892FSP router, see Figure 3-32.
Figure 3-31 Connecting the AC Adapter
1 12-VDC plug 3 Power adapter—12 VDC
2 Power cord 4 AC plug
231996
1
2
4
3
3-37
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Figure 3-32 Connecting the AC Adapter for the Cisco 892FSP
Figure 3-33 Cisco 892FSP, 896VA, 897VA, and 898EA Power Adapter Connector Pin Assignment
7 6 GE LAN 5 4
9
GE WAN
8
GE WAN
SFP
8
12VDC 2.5A
CONSOLE
AUX
RESET
Cisco 892FSP
343746
1
2
4
3
1 12-VDC plug 3 Power adapter—12 VDC
2 Power Adapter Cord 4 AC Plug
284800
Pin 3
Pin 1
Pin 4
Pin 2
Pin 1 Ground Pin 3 +12 V
Pin 2 NC
1
Pin 4 NC
1. NC = No Connection.
3-38
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Step 2 To secure the power cord to the router, attach the power lock clip to the power cord, slide the clip to the
end of the DC plug, and secure the retaining clip into the router chassis. See Figure 3-34.
Figure 3-34 Securing the Power Cord
1 Power lock clip 3 DC plug
2 Power cord 4 Lock holes on either side of the power
connector
270659
4
2
1
3
3-39
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Step 3 Snap the latches into the holes on either side of the power connector. See Figure 3-35.
Figure 3-35 Power Lock Clip Latched Into the Holes on Either Side of the Power Connector
Connecting an FXS Line
Use a standard straight-through RJ-11 modular telephone cable to connect a Foreign Exchange Service
(FXS) port to a telephone or fax machine.
Warning
This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do
not touch the RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11
port, or the associated circuit-board when the ringer is active. The ringer is activated by an incoming
call.
Statement 1042
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first.
Statement 1026
Warning
For connections outside the building where the equipment is installed, the following ports must be
connected through an approved network termination unit with integral circuit protection: FXS.
Statement 1044
1 Power lock clip 3 Power adapter
2 Power cord 4 AC plug
270800
1
2
4
3
3-40
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
To connect the FXS line, follow these steps:
Step 1 Connect one end of the straight-through RJ-11 cable to the FXS port.
Figure 3-36 shows an FXS line connection.
Figure 3-36 Connecting an FXS Line
Step 2 Connect the other end of the cable to the RJ-11 port on the fax machine or telephone.
Connecting an FXO Line
Use a straight-through RJ-11 cable to connect the FXO voice port to the PSTN or PBX through a
telephone wall outlet.
1 FXS port 3 RJ-11 port
2 RJ-11 cable
Fax machine
or telephone
241907
1
2
3
3-41
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first.
Statement 1026
To connect the FXO line, follow these steps:
Step 1 Connect one end of the straight-through RJ-11 cable to the FXO port. See Figure 3-37.
Figure 3-37 Connecting an FXO Line
Step 2 Connect the other end of the RJ-11 cable to a telephone wall outlet.
Note If you have specified the use of a private line automatic ringdown (PLAR) off-premises extension (OPX)
connection mode for an FXO voice port (with loop resistance less than 8000 Ohm), you must ensure that
the soft-offhook option is enabled on the port.
1 FXO port 3 Telephone outlet
2 RJ-11 cable
270542
2
1
3
3-42
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
This option allows a stepped offhook resistance during seizure, which avoids overloading the circuit
during offhook in the event that ringing voltage is present on the circuit at the same time as the trunk
seizure. The stepped offhook resistance is initially set to 800 Ohms, then adjusts to 50 Ohms when
ringing voltage is not present.
To enable the soft-offhook command on the port, and to access the connection command with plar opx
syntax, see the Cisco Command Lookup Tool.
Connecting a Voice ISDN BRI Line
Use a straight-through RJ-45 cable to connect the voice BRI port to the ISDN network through a
telephone outlet or other device.
Caution To prevent damage to the router, be sure to connect the BRI cable to the BRI connector only and not to
any other RJ-45 connector.
To connect the voice BRI line, follow these steps:
Step 1 Connect one end of a straight-through RJ-45–to–RJ-45 cable to the Voice BRI port.
Note When the interface is configured as NT and is connecting to a TE device, use a crossover cable.
See Table A-27.
3-43
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Figure 3-38 shows a voice BRI line connection.
Figure 3-38 Connecting a Voice BRI Line
Step 2 Connect the other end of the cable to the RJ-45 telephone outlet or other device.
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments.
Statement 1051
Warning
Do not stare into the laser beam.
Statement 1010
Warning
Invisible laser radiation present.
Statement 1016
1 Voice BRI port 3 Telephone outlet
2 RJ-45 cable
241906
1
3
2
3-44
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning
Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do
not view directly with optical instruments. Viewing the laser output with certain optical instruments
(for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye
hazard.
Statement 1056
Warning
Use of controls, adjustments, or performing procedures other than those specified may result in
hazardous radiation exposure.
Statement 1057
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments.
Statement 1051
1 Sliding latch 3 Bale-clasp latch
2 Swing and slide latch 4 Plastic collar latch
117722
1 2 3 4
A
B
3-45
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
Verifying Connections
To verify that all devices are properly connected to the router, first turn on all the connected devices,
then check the LEDs. To verify router operation, refer to Table 3-1.
For the full LED descriptions, see the “LEDs” section on page 1-135.
Table 3-4 Verifying the Router Operation
Power and Link LEDs to Check Normal Patterns
Power OK On when power is supplied to the router.
To servers, PCs,
workstations, or an
external Ethernet
switch connected to
the LAN ports
(FE0
1
, FE1, FE2, or
FE3)
LAN 0, LAN 1,
LAN 2, or LAN 3
On when the FE LAN port is physically connected to a
server, PC, workstation, or external Ethernet switch.
To FE WAN line WAN FE4 On when the WAN Ethernet carrier has detected status.
Blinks when receiving or transmitting data.
To xDSL
2
line xDSL CD Green when the line is connected to the xDSL DSLAM
3
.
xDSL Data Green when receiving or sending data.
Blinks when line is in training mode.
ATM 898EA only Green when ATM mode is selected.
EFM 898EA only Green when EFM mode is selected.
To ISDN line Data BRI LNK Green when the ISDN line is connected.
Data BRI B1 and
B2
Green when the channel is connected.
3G
4
WWAN
5
Green when service is established.
Slow blinking when searching for service.
RSSI
6
Amber when service is not established.
Green when signal strength is high.
Off or slow blinking when signal strength is low.
Fast blinking when signal strength is medium.
CDMA
7
Green when service is established.
GSM
8
Green when service is established.
To PPP
9
clients PPP Green when either a PPPoE
10
or PPPoA
11
client is running.
To VPN
12
tunnel VPN Green when a crypto session is running.
3-46
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
To wireless LAN WLAN LINK Wireless LAN link status:
Green if at least one client is associated.
Off if no client is associated.
WLAN 2.4 GHz Wireless LAN 2.4-GHz status:
Green when radio is connected, SSID
13
is configured,
signal is being transmitted, and client is associated.
Slow blinking when radio is connected, SSID is
configured, and signal is being transmitted.
WLAN 5.0 GHz Wireless LAN 5.0-GHz status:
Green when radio is connected, SSID is configured,
signal is being transmitted, and client is associated.
Slow blinking when radio is connected, SSID is
configured, and signal is being transmitted.
PoE
14
PoE 0 (880 and
890 series only)
PoE power status:
Green when connected and powered.
Amber when there is a fault with the inline power
supply.
PoE 1 (880 and
890 series only)
PoE 2 (890 series
only)
PoE 3 (890 series
only)
To LAN GE/FE line
(860VAE models
only)
LAN Blinking when there is LAN activity (traffic in either
direction).
Off when the link is down.
To DSL line
(860VAE models
only)
DSL LINK On when DSL WAN mode is selected and DSL training
complete.
Blinking when DSL WAN mode is selected but incomplete
DSL LinkUp state such as in-training (slow initially, fast
when almost connected), or controller "OFF", or no cable
attached to DSL connector.
Off when the device is powered off; or GE WAN mode is
selected.
DSL ACT On when the DSL interface is up.
Blinking when there is DSL WAN activity (traffic in either
direction).
Faster blinking when there is heavier traffic.
Off when the device is powered off or the DSL WAN
interface is down.
Table 3-4 Verifying the Router Operation (continued)
Power and Link LEDs to Check Normal Patterns
3-47
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
To WAN GE line
(860VAE models
only)
GE Mode On when GE WAN mode is selected.
Off when the device is powered off or when DSL WAN
mode is selected.
GE ACT On when the GE WAN interface is up.
Blinking when there is GE WAN activity (traffic in either
direction).
Off when the device is powered off or when the GE WAN
interface is down.
1. FE = Fast Ethernet.
2. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line), VDSL
(very-high-data-rate digital subscriber line), and G.SHDSL.
3. DSLAM = digital subscriber line access multiplexer.
4. 3G = Third-Generation.
5. WWAN = wireless WAN.
6. RSSI = Received Signal Strength Indicator.
7. CDMA = code division multiple access.
8. GSM = Global System for Mobile Communications.
9. PPP = Point-to-Point Protocol.
10. PPPoE = PPP over Ethernet.
11. PPPoA = PPP over ATM.
12. VPN = Virtual Private Network.
13. SSID = service set identifier.
14. PoE = Power over Ethernet.
Table 3-4 Verifying the Router Operation (continued)
Power and Link LEDs to Check Normal Patterns
3-48
Cisco Integrated Services Router Hardware Installation Guide
Chapter 3 Connecting the Router
Cisco 860, 880, 890 Series
CHAPTER
4-1
Cisco Integrated Services Router Hardware Installation Guide
4
Initial Configuration
This chapter provides instructions for initial configuration of the Cisco 819, 860, 880, 890 Series
Integrated Services Routers (ISRs), and contains the following sections:
Cisco 810 Series, page 4-1
Cisco 860, 880, 890 Series, page 4-2
Cisco 810 Series
Cisco 819 Series
This section provides instructions for initial configuration of the Cisco 819 ISRs. For the initial
configuration, we recommend using Cisco Configuration Professional Express. For instructions on how
to use Cisco Configuration Professional Express to configure the router, see Cisco Configuration
Professional Express User’s Guide.
You may also initially configure your router by using the Cisco IOS command-line interface (CLI) or by
using the setup command facility. To create the initial configuration, the setup command facility prompts
you for basic information about your router and network.
This section contains the following topics:
Cisco IOS CLI, page 4-1
Setup Command Facility, page 4-1
Verifying the Initial Configuration, page 4-2
Cisco IOS CLI
To configure the initial router settings by using the Cisco IOS CLI, you must set up a console connection.
To configure the initial router settings using the Cisco IOS CLI, refer to the Cisco IOS CLI, page 4-2.
For instructions on how to set up a console connection, see the “Connecting a Terminal or PC to the
Console Port” section on page 3-16.
Setup Command Facility
For more information, refer to the “Setup Command Facility” section on page 4-4.
4-2
Cisco Integrated Services Router Hardware Installation Guide
Chapter 4 Initial Configuration
Cisco 860, 880, 890 Series
Verifying the Initial Configuration
For more information, refer to the “Verifying the Initial Configuration” section on page 4-6.
Cisco 860, 880, 890 Series
This section provides instructions for initial configuration of the Cisco 860 series, 880 series, and 890
series ISRs. You may also initially configure your router by using the Cisco IOS command-line interface
(CLI) or by using the setup command facility. To create the initial configuration, the setup command
facility prompts you for basic information about your router and network.
This section contains the following topics:
Cisco Configuration Professional Express, page 4-2
Cisco IOS CLI, page 4-2
Setup Command Facility, page 4-4
Verifying the Initial Configuration, page 4-6
Initial Configuration of the Wireless Access Point, page 4-7
Note Some SKUs may not include a default configuration file. If your router does not have a default
configuration file, go to the “Setup Command Facility” section on page 1 to configure the initial router
settings.
Cisco Configuration Professional Express
After you connect the cables and power up the router, we recommend that you use the Cisco
Configuration Professional Express web-based application to configure the initial router settings.
For instructions on how to use Cisco Configuration Professional Express to configure the router, see
Cisco Configuration Professional Express User’s Guide.
Cisco IOS CLI
To configure the initial router settings by using the Cisco IOS CLI, you must set up a console connection.
For instructions on how to set up a console connection, see the “Connecting a Terminal or PC to the
Console Port” section on page 3-16.
To configure the initial router settings using the Cisco IOS CLI, follow these steps:
Step 1 Set up a console connection to your router. The following message is displayed:
...
router con0 is now available
Step 2 Press Return. The following message is displayed:
Cisco Configuration Professional Express (Cisco CP Express) is installed on this device.
This feature requires the one-time use of the username "username1"
with the password "password1." The default username and password have a privilege level of
15.
4-3
Cisco Integrated Services Router Hardware Installation Guide
Chapter 4 Initial Configuration
Cisco 860, 880, 890 Series
Please change these publicly known initial credentials using Cisco CP Express or the Cisco
IOS CLI.
Here are the Cisco IOS commands.
username <myuser> privilege 15 secret 0 <mypassword>
no username username1
Replace <myuser> and <mypassword> with the username and password you want to use.
For more information about Cisco CP please follow the instructions in the QUICK START
GUIDE for your router...
...
User Access Verification
Username:
Step 3 Enter the username username1, and press Return or Enter. The following prompt is displayed:
Password:
Step 4 Enter the password password1, and press Return or Enter. The following prompt is displayed:
Router#
A message is displayed that is similar to the first warning message. The message directs you to change
the username and password.
You are now in privileged EXEC mode.
Note You must change the username and password before you log off the router. You cannot use the
username username1 or password password1 after you log off from this session.
Step 5 Enter configuration mode using the following commands.
Router#
Router#config t
Router(config)#
Router(config)#username username privilege 15 secret 0 password
Step 6 To change the username and password, enter the following at the prompt:
username username privilege 15 secret 0 password
The username and password are the username and password that you determine.
To continue using the Cisco IOS CLI for initial configuration, see the applicable configuration
procedures in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers
Software Configuration Guide.
Note Save your configuration changes regularly to avoid losing them during resets, power cycles, or
power outages. Use the copy running-config startup-config command at the privileged EXEC
mode prompt (Router#) to save the configuration to NVRAM.
Step 7 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-2.
4-4
Cisco Integrated Services Router Hardware Installation Guide
Chapter 4 Initial Configuration
Cisco 860, 880, 890 Series
Setup Command Facility
The setup command facility guides you through the configuration process by prompting you for the
specific information that is needed to configure your system. Use the setup command facility to
configure a hostname for the router, to set passwords, and to configure an interface for communication
with the management network.
To use the setup command facility, you must set up a console connection with the router and enter the
privileged EXEC mode.
Note For instructions on how to set up a console connection, see the “Connecting a Terminal or PC to
the Console Port” section on page 3-16.
To configure the initial router settings by using the setup command facility, follow these steps:
Step 1 Set up a console connection to your router, and enter privileged EXEC mode. For instructions on how to
enter privileged EXEC mode, see Step 1 through Step 4 in the “Cisco IOS CLI” section on page 4-1.
Step 2 In privileged EXEC mode, at the prompt, enter setup.
yourname# setup
The following message is displayed:
--- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]:
You are now in the setup command facility.
The prompts in the setup command facility vary, depending on your router model, on the installed
interface modules, and on the software image. The following steps and the user entries (in bold) are
shown as examples only.
Note If you make a mistake while using the setup command facility, you can exit and run the setup
command facility again. Press Ctrl-C, and enter the setup command at the privileged EXEC
mode prompt (Router#). For more information on using the setup command facility, see “The
Setup Command” chapter in Cisco IOS Configuration Fundamentals Command Reference,
Release 12.2T.
Step 3 To proceed using the setup command facility, enter yes.
Continue with configuration dialog? [yes/no]: yes
Step 4 When the following messages appear, enter yes to enter basic management setup.
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]: yes
4-5
Cisco Integrated Services Router Hardware Installation Guide
Chapter 4 Initial Configuration
Cisco 860, 880, 890 Series
Step 5 Enter a hostname for the router (this example uses Router).
Configuring global parameters:
Enter host name [Router]: Router
Step 6 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when
viewing the configuration.
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret: xxxxxx
Step 7 Enter an enable password that is different from the enable secret password. This password is not
encrypted (less secure) and can be seen when viewing the configuration.
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: xxxxxx
Step 8 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports
other than the console port.
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: xxxxxx
Step 9 Respond to the following prompts as appropriate for your network.
Configure SNMP Network Management? [yes]:
Community string [public]:
A summary of the available interfaces is displayed.
Step 10 Choose one of the available interfaces for connecting the router to the management network.
Enter interface name used to connect to the
management network from the above interface summary: fastethernet4
Step 11 Respond to the following prompts as appropriate for your network.
Configuring interface FastEthernet4:
Use the 100 Base-TX (RJ-45) connector? [yes]: yes
Operate in full-duplex mode? [no]: yes
Configure IP on this interface? [yes]: yes
IP address for this interface: 172.1.2.3
Subnet mask for this interface [255.255.0.0] : 255.255.0.0
Class B network is 172.1.0.0, 26 subnet bits; mask is /16
4-6
Cisco Integrated Services Router Hardware Installation Guide
Chapter 4 Initial Configuration
Cisco 860, 880, 890 Series
The configuration is displayed:
The following configuration command script was created:
hostname Router
enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1
enable password xxxxxx
line vty 0 4
password xxxxxx
snmp-server community public
!
no ip routing
!
interface FastEthernet4
no shutdown
speed 100
duplex auto
ip address 172.1.2.3 255.255.0.0
!
Step 12 Respond to the following prompts. Enter 2 to save the initial configuration.
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
Enter your selection [2]: 2
Building configuration...
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started! RETURN
The user prompt is displayed.
Router>
Step 13 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-2 for
verification procedures.
After the initial configuration file is created, you can use the Cisco IOS CLI to perform additional
configuration.
Verifying the Initial Configuration
To verify that the new interfaces are operating correctly, perform the following tests:
To verify that the interfaces and line protocol are in the correct state—up or down—enter the show
interfaces command.
To display a summary status of the interfaces configured for IP, enter the show ip interface brief
command.
To verify that you configured the correct hostname and password, enter the show configuration
command.
After you complete and verify the initial configuration, you can configure your Cisco router for specific
functions.
4-7
Cisco Integrated Services Router Hardware Installation Guide
Chapter 4 Initial Configuration
Cisco 860, 880, 890 Series
Initial Configuration of the Wireless Access Point
The embedded wireless access point (AP) runs its own IOS. You can initially configure the embedded
wireless AP by using one of the following methods:
Cisco Configuration Professional Express
Setup command facility on the embedded wireless device
For information on how to do basic wireless configuration on your router see the Basic Wireless
Device” chapter of the Cisco 860 Series, Cisco 880, and Cisco 890 Series Integrated Services Routers
Software Configuration Guide.
4-8
Cisco Integrated Services Router Hardware Installation Guide
Chapter 4 Initial Configuration
Cisco 860, 880, 890 Series
A-1
Cisco Integrated Services Router Hardware Installation Guide
APPENDIX
A
Technical Specifications
This appendix provides specifications for the Cisco 860, 880, 890 Series ISRs, Cisco 819 ISRs, and the
Cisco 812 ISRs:
Cisco 810 Series, page A-1
Cisco 860, 880, 890 Series, page A-11
Cisco 810 Series
This section contains the following:
Cisco 812 Series, page A-1
Cisco 819 Series, page A-4
Cisco 812 Series
This section provides specifications for the Cisco 812 Integrated Services Router (ISRs) and contains
the following topics:
Router Specifications, page A-1
Mean Time Between Failure Ground Benign Environment, page A-4
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Note For compliance and safety information, see Regulatory Compliance and Safety Information for
Cisco 800 Series Routers.
Router Specifications
Table A-1 lists the operational limits of the Cisco 812 ISR. Operating the router outside of the limits
specified is not supported.
A-2
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 810 Series
Table A-1 Cisco 812 ISR Specifications
Description
C812G+7-K9
(3G only)
C812G-CIFI+7-E-K9
C812G-CIFI+7-N-K9
C812G-CIFI-V-A-K9
C812G-CIFI-S-A-K9
(3G + WiFi)
Physical Characteristics
Dimensions (H x W x D) 2.01 x 8.95 x 9.49 inches (51 x 227x 241 mm)
Weight 3.96 lbs (1.8 kg)
Maximum Power Consumption 11 W 18 W
Extended Shock-vibe No
IP41 (with DC adapter) No
Environmental Operating Ranges
Operating Temperature and
Altitude
–32 to 104 °F (0 to 40 °C)
Derate max operating temperature 1.5 °C per 1000 ft above 5000 ft
10,000 ft maximum except CCC
1
only up to 2000 meters.
Humidity Maximum 85% non-condensing RH
Ingress Protection Rating IP 20 per IEC 60529
Standard Safety Certifications
UL 60950-1, 2nd edition
CAN/CSA C22.2 No. 60950-1, 2nd edition
EN 60950-1, 2nd edition
CB to IEC 60950-1, 2nd edition with all group differences and national deviations
AS/NZS 60950-1, Edition 1 (Australia and New Zealand)
EMC Emissions
EN55022/CISPR22
CFR 47 Part 15
ICES003
VCCI-V-3
AS/NZS CISPR22
CNS13438
CISPR22
CNS13438
EN300-386
EN61000-3-2
EN61000-3-3
EN61000-6-1
EMC Immunity
EN55024/CISPR24 (EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5,
EN61000-4-6, EN61000-4-11)
EN300-386
A-3
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 810 Series
Radio Immunity EN301 489-1, EN 301 489-7, and EN301 489-24
Transportation/Storage Conditions
Temperature –40 to158 °F (–40 to 70°C)
Humidity 5–95%
Altitude 4570 m (15,000 ft)
AC Power Adapter
Power Source 100–240 VAC
In-ceiling Plenum No
IP41 No
Extended Shock-vibe No
Maximum Power Consumption 25 W
Maximum Output Power Rating 20 W
Operating Temperature –13 to 140 °F (–25 to 60 °C)
PoE+ Splitter
Power Source PoE+ (IEEE802.3at Class 4)
In-ceiling Plenum Yes
IP41 No
Extended Shock-vibe No
Maximum Power Consumption 25 W
Maximum Output Power Rating 20 W
Operating Temperature –13 to 140 °F (–25 to 60 °C)
Embedded WiFi Antenna
Frequency Range 2.4–2.5 Ghz
4.9–5.875 Ghz
Peak Gain 4 dBi (2.4 GHz)
6 dBi (5.875 Ghz)
Voltage Standing Wave Ratio 2.5:1 maximum for all bands
Nominal Impedance 50 ohms
1. Routers shipped in People’s Republic of China.
Table A-1 Cisco 812 ISR Specifications (continued)
Description
C812G+7-K9
(3G only)
C812G-CIFI+7-E-K9
C812G-CIFI+7-N-K9
C812G-CIFI-V-A-K9
C812G-CIFI-S-A-K9
(3G + WiFi)
A-4
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 810 Series
Mean Time Between Failure Ground Benign Environment
Table A-2 lists the Mean Time Between Failure (MTBF) values for Cisco 812 ISRs. The MTBF is
calculated based on the Ground Benign condition. The values may be adjusted based on the different
router usage.
Cisco 819 Series
This section provides router, port, cabling specifications, and power adapters for the Cisco 812 ISRs and
contains the following topics:
Router Specifications, page A-4
Mean Time Between Failure Ground Benign Environment, page A-8
Supported Power Adapters, page A-9
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Note For compliance and safety information, see the Regulatory Compliance and Safety Information
Roadmap that was shipped with the router and Regulatory Compliance and Safety Information for
Cisco 800 Series Routers.
Router Specifications
Table A-1 lists the operational limits of the Cisco 819 ISR. Operating the router outside of the limits
specified is not supported. For the complete list of SKUs available for each Cisco 819 ISRs, see the
“SKU Information” section on page 1-14.
Table A-2 MTBF Values
SKUs MTBF (hours)
C812G-CIFI-V-A-K9
C812G-CIFI-S-A-K9
210,000
C812G-CIFI+7-E-K9
C812G-CIFI+7-N-K9
280,000
C812G+7-K9 340,000
A-5
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 810 Series
Table A-3 Cisco 819 ISR Specifications
Description
Hardened Design
Specification
(Cisco 819HG and Cisco
819HG-4G ISRs)
Non-Hardened Design
Specifications
(Cisco 819G and Cisco
819G-4G ISRs)
Hardened Design Specifications
(C819HGW and C819HWD ISRs)
Physical Characteristics
Dimensions (H x W x D) 1.73 x 7.7 x 8.1 in
(44 x 196 x 206 mm)
1.67 x 7.7 x 7.2 in
(42 x 196 x 183 mm)
1.73 x 7.7 x 9.0 in
(44 x 196 x 229 mm)
Weight 3.3 lb (1.5 kg) 2.3 lb (1.0 kg) 3.4 lb (1.54 kg)
Maximum Power
Consumption
11 W 20 W
Environmental Operating Ranges
Operating Temperature and
Altitude
–13 to 140°F
(–25 to 60°C)
32 to 104°F
(0 to 40°C)
–13 to 140°F
(–25 to 60°C)
Derate max operating temperature 1.5°C per 1000 feet above 5000 ft
10,000 ft maximum
Humidity Maximum 95%
non-condensing RH
Maximum 85%
non-condensing RH
Maximum 95% non-condensing
RH
Environmental Tests
Ingress Protection Rating IP 41 per IEC 60529 for
Vertical Falling Water,
Pollution Degree 3
IP 20 per IEC 60529 IP 41 per IEC 60529 for Vertical
Falling Water, Pollution Degree 3
Humidity Non-condensing Relative Humidity: 5% to 95%
Pollution Pollution 3 for Dust
Military Standard MIL-STD-810G Method 514.6: Procedure 1 Category 4, Secured Cargo - Common Carrier
MIL-STD-810G Method 514.6: Procedure 1 Category 20, Ground Vehicles
MIL-STD-810G Method 516.6. Procedure 1, Functional Shock
MIL-STD-810G Method 516.6. Procedure 5, Crash Hazard
MIL-STD-810G Method 516.6. Procedure 6, Bench Handling
Vibration and Shock
(Railway Vehicles)
EN61373 Functional Random Vibe - Category 1, Class B
EN61373 Simulated Non-op Long-life Vibe - Category 1, Class B
EN61373 Non-op Shock, Class B
Heavy-Duty Vehicle
Applications
SAE J1455 Operating Random Vibe, Cab Mounted Truck
SAE J1455 Operating Sinusoidal Vibe, Category 3
SAE J1455 Non-operating Sinusoidal Vibe, Category 3
SAE J1455 Handling Drop Test
Certifications
A-6
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 810 Series
Standard Safety
Certifications
UL 60950-1, 2nd edition; CAN/CSA C22.2 No. 60950-1,
2nd edition, EN 60950-1, 2nd edition; CB to IEC
60950-1, 2nd edition with all group differences and
national deviations
UL 60950-1, 2nd edition;
CAN/CSA C22.2 No. 60950-1, 2nd
edition, EN 60950-1, 2nd edition;
CB to IEC 60950-1, 2nd edition
with all group differences and
national deviations; S/NZS
60950-1, first edition
(Australia/New Zealand)
EMC Emissions EN55022/CISPR22, CFR 47 Part 15, ICES003, VCCI-V-3, AS/NZS CISPR22, CNS13438,
CISPR22, CNS13438, EN300-386, EN61000-3-2, EN61000-3-3, and EN61000-6-1
EMC Immunity EN55024/CISPR24, (EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5,
EN61000-4-6, EN61000-4-11), and EN300-386
Radio Immunity EN301 489-1, EN 301 489-7, and EN301 489-24
Transportation/Storage Conditions
Temperature –40 to158°F (–40 to 70°C) –40 to185°F
(–40 to 85°C)
Humidity 5–95%
Altitude 4570 m (15,000 ft)
Router AC Power Adapter
1
Input Voltage 85–264 VAC
100–240 VAC nominal
Maximum Power
Consumption
25 W
Maximum Output Power
Rating
20 W
(5 VDC, 4 Amps)
Router DC Power Adapter
Input Voltage 12 VDC nominal
PWRx-20W-12VDC (10 VDC to 36 VDC operating range)
24 VDC nominal
PWRx-20W-24VDC (18 VDC to 75 VDC operating range)
Maximum Power
Consumption
25 W
Maximum Output Power
Rating
20 W
(5 VDC, 4 Amps)
Table A-3 Cisco 819 ISR Specifications (continued)
Description
Hardened Design
Specification
(Cisco 819HG and Cisco
819HG-4G ISRs)
Non-Hardened Design
Specifications
(Cisco 819G and Cisco
819G-4G ISRs)
Hardened Design Specifications
(C819HGW and C819HWD ISRs)
A-7
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 810 Series
Altitude Operating: –500 to 10,000 ft, de-rating operating temperature 1°C per 1,000 feet
Non-operating: –1,000 to 30,000 ft
Cable Length Input cable: 1 m
Output cable: 1.3 m
Inrush Current 50 A @ 25°C
Temperature Operating: –30 to 60°C, still air condition
Non-operating: –40 to 85°C
Humidity Operating: 10% to 95%, non-condensing
Non-operating: 10% to 95%, non-condensing
Thermal Shock Operating: –20 to 60°C at 0.5°C per minute
Non-operating: –40 to 85°C with change over time between 2 and 3 minutes.
Vibration Operating: 0.41 grms from 3 to 500 Hz with spectral break points of 0.0005 g2/Hz at 10 Hz
and 200 Hz and 5 dB/octave roll off at each end; 2 hours per axis.
Non-Operating: 1.12 grms from 3 to 500 Hz with spectral break points of 0.0065 g2/Hz at 10
Hz and 100 Hz and 5 dB/octave roll off at each end; 30 minutes per axis.
Shock Half sine (operating):
Duration = <2ms
Velocity = 2.11m/s
Number of shocks: a series of 6 shocks one on each side
Trapezoidal shock (non-operating):
Duration = 12 to 25 ms
Number of shocks: a series of 6 shocks one on each side
Martek Railway Power Adapters
2
Nominal Input Voltages 24 V
52 V
72 V
In-ceiling Plenum No
IP 65 Yes
Extended Shock-vibe Yes
EN50155 (EN61373) and RIA20
Maximum Power
Consumption
——25 W
Maximum Output Power
Rating
——20 W
Operating Temperature –13 to 140°F
(–25 to 60°C)
Table A-3 Cisco 819 ISR Specifications (continued)
Description
Hardened Design
Specification
(Cisco 819HG and Cisco
819HG-4G ISRs)
Non-Hardened Design
Specifications
(Cisco 819G and Cisco
819G-4G ISRs)
Hardened Design Specifications
(C819HGW and C819HWD ISRs)
A-8
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 810 Series
Mean Time Between Failure Ground Benign Environment
Table A-4 lists the Mean Time Between Failure (MTBF) values for Cisco 819 ISRs. The MTBF is
calculated based on the Ground Benign condition. The values may be adjusted based on the different
router usage.
Antenna (Diversity and Antenna 3G-ANTM1919D)
Antenna Dimensions 7.63 x 0.94 x 0.63 in (19.38 x 2.39 x 1.60 cm)
Frequency Range 806 to 960 MHz and 1710 to 2170 MHz
Gain 0 decibels relative to isotropic (dBi) (806 to 960 MHz) and 0 dBi (1710 to 2170 MHz)
Maximum Power 25 W
Connector TNC male
Voltage Standing Wave
Ratio
< 2.5:1
Nominal Impedance 50 ohms
1. AC Power Adapter is not IP 41 rated. Installation must include protection of the adapter and power plug from water.
2. Contact Martek Power directly for details.
Table A-3 Cisco 819 ISR Specifications (continued)
Description
Hardened Design
Specification
(Cisco 819HG and Cisco
819HG-4G ISRs)
Non-Hardened Design
Specifications
(Cisco 819G and Cisco
819G-4G ISRs)
Hardened Design Specifications
(C819HGW and C819HWD ISRs)
Table A-4 MTBF Values
SKUs MTBF (hours)
Cisco 819HG and Cisco 819G ISRs
C819HG-U-K9
C819G-U-K9
380,000
C819HG+7-A-K9
C819HG+7-K9
C819G+7-A-K9
C819G+7-K9
420, 000
C819HG-S-K9
C819HG-V-K9
C819HG-B-K9
C819G-S-K9
C819G-V-K9
C819G-B-K9
280, 000
Cisco 819HGW, Cisco 819HWD, and Cisco 819H ISRs
A-9
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 810 Series
Supported Power Adapters
Table A-5 and Table A-6 list the supported power adapters for Cisco 819 ISRs. The PWR1 AC and DC
adapters uses molex connector while PWR2 uses barrel-type connector.
C819HGW-S-A-K9
C819HGW-V-A-K9
220,000
C819HGW+7-E-K9
C819HGW+7-N-K9
C819HGW+7-A-A-K9
293,000
C819HWD-E-K9
C819HWD-A-K9
630,000
C819H-K9 1,000,000
Cisco 819HG-4G and Cisco 819G-4G ISRs
C819HG-4G-V-K9
C819G-4G-V-K9
214,000
C819HG-4G-A-K9
C819G-4G-A-K9
226,000
C819HG-4G-G-K9
C819G-4G-G-K9
293,000
Table A-4 MTBF Values (continued)
SKUs MTBF (hours)
Table A-5 Cisco 819G ISR Power Adapters
Power Adapter
Nominal Input
Range
C819G-4G-A-K9
C819G-4G-V-K9
C819G-4G-G-K9
(4G LTE SKUs)
C819G+7-K9
C819G-B-K9
C819G-S-K9
C819G-U-K9
C819G-V-K9
(3GSKUs)
PWR1-20W-AC 100–240 VAC Yes
PWR2-20W-AC 100–240 VAC Yes
PWR1-20W-12VDC 12 VDC Yes
PWR2-20W-12VDC 12 VDC Yes
PWR1-20W-24VDC 24 VDC Yes
PWR2-20W-24VDC 24 VDC Yes
PWR2-22W-20-60VDC 20-60VDC Yes
Martek MBRH 0500-B/Q21 24 VDC Yes
Martek MBRH 0500-C/Q21 52 VDC Yes
A-10
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 810 Series
Martek MBRH 0500-D/Q21 72 VDC Yes
Martek MBRH 0500-D/2Q21 24 VDC Yes Yes
Martek MBRH 0500-D/2Q21 52 VDC Yes Yes
Martek MBRH 0500-D/2Q21 72 VDC Yes Yes
Martek MBRH 0500-D/2Q21 110 VDC Yes Yes
Martek MBRH 0500-B/Q22 24 VDC Yes
Martek MBRH 0500-C/Q22 52 VDC Yes
Martek MBRH 0500-D/Q22 72 VDC Yes
Martek MBRH 0500-D/2Q22 24 VDC Yes Yes
Martek MBRH 0500-D/2Q22 52 VDC Yes Yes
Martek MBRH 0500-D/2Q22 72 VDC Yes Yes
Martek MBRH 0500-D/2Q22 110 VDC Yes Yes
Table A-5 Cisco 819G ISR Power Adapters
Power Adapter
Nominal Input
Range
C819G-4G-A-K9
C819G-4G-V-K9
C819G-4G-G-K9
(4G LTE SKUs)
C819G+7-K9
C819G-B-K9
C819G-S-K9
C819G-U-K9
C819G-V-K9
(3GSKUs)
Table A-6 Cisco 819H ISR Power Adapters
Power Adapter
Nominal Input
Range
C819HG-4G-A-K9
C819HG-4G-V-K9
C819HG-4G-G-K9
(4G LTE SKUs)
C819HG+7-K9
C819HG-B-K9
C819HG-S-K9
C819HG-U-K9
C819HG-V-K9
(3G SKUs)
C819HGW-S-A-K9
C819HGW-V-A-K9
C819HGW+7-E-K9
C819HGW+7-N-K9
C819HGW+7-A-A-K9
(3G + WiFi SKUs)
C819HWD-E-K9
C819HWD-A-K9
(WiFi SKUs)
C819H-K9
(Serial SKU)
PWR1-20W-AC 100–240 VAC Yes
PWR2-20W-AC 100–240 VAC Yes Yes Yes Yes
PWR1-20W-12VDC 12 VDC Yes
PWR2-20W-12VDC 12 VDC Yes Yes Yes Yes
PWR1-20W-24VDC 24 VDC Yes
PWR2-20W-24VDC 24 VDC Yes Yes Yes Yes
Martek MBRH
0500-B/Q21
24 VDC Yes
Martek MBRH
0500-C/Q21
52 VDC Yes
Martek MBRH
0500-D/Q21
72 VDC Yes
A-11
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Cisco 860, 880, 890 Series
This section provides router, port, and cabling specifications for the Cisco 860 series, Cisco 880 series,
and Cisco 890 series ISRs. It contains the following topics:
Router Specifications, page A-12
Wireless Access Point, page A-22
FE and GE Port Pinouts, page A-23
Console and Auxiliary Port Connector Pinouts, page A-24
FXS and FXO Port Connector Pinouts, page A-24
VDSL2 Port Connector Pinouts, page A-24
ADSL2+ Port Connector Pinouts, page A-25
V.92 Port Connector Pinouts, page A-25
Martek MBRH
0500-D/2Q21
24 VDC Yes Yes Yes Yes Yes
Martek MBRH
0500-D/2Q21
52 VDC Yes Yes Yes Yes Yes
Martek MBRH
0500-D/2Q21
72 VDC Yes Yes Yes Yes Yes
Martek MBRH
0500-D/2Q21
110 VDC Yes Yes Yes Yes Yes
Martek MBRH
0500-B/Q22
24 VDC Yes Yes Yes Yes
Martek MBRH
0500-C/Q22
52 VDC Yes Yes Yes Yes
Martek MBRH
0500-D/Q22
72 VDC Yes Yes Yes Yes
Martek MBRH
0500-D/2Q22
24 VDC Yes Yes Yes Yes Yes
Martek MBRH
0500-D/2Q22
52 VDC Yes Yes Yes Yes Yes
Martek MBRH
0500-D/2Q22
72 VDC Yes Yes Yes Yes Yes
Martek MBRH
0500-D/2Q22
110 VDC Yes Yes Yes Yes Yes
Table A-6 Cisco 819H ISR Power Adapters (continued)
Power Adapter
Nominal Input
Range
C819HG-4G-A-K9
C819HG-4G-V-K9
C819HG-4G-G-K9
(4G LTE SKUs)
C819HG+7-K9
C819HG-B-K9
C819HG-S-K9
C819HG-U-K9
C819HG-V-K9
(3G SKUs)
C819HGW-S-A-K9
C819HGW-V-A-K9
C819HGW+7-E-K9
C819HGW+7-N-K9
C819HGW+7-A-A-K9
(3G + WiFi SKUs)
C819HWD-E-K9
C819HWD-A-K9
(WiFi SKUs)
C819H-K9
(Serial SKU)
A-12
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
G.SHDSL Port Connector Pinouts, page A-25
Data BRI Port Connector Pinouts, page A-26
Voice ISDN BRI Interface Pin Numbers and Functions, page A-27
SFP Port Connector Pinouts, page A-27
Cable Specifications, page A-28
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap
that was shipped with the router and Regulatory Compliance and Safety Information for Cisco 800 Series
Routers.
Note The product has some color variation on the Power Pin. This will not impact product performance or
reliability.
Router Specifications
This sections contains the following:
All Models Except Cisco 860VAE Series, page A-12
Cisco 860VAE Series, page A-14
Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 Series,
page A-15
Cisco 870 Series, page A-16
Cisco 880 Series, page A-17
Cisco 880G Series 3G Wireless Integrated Services Router, page A-19
Cisco 880VA Series, page A-19
Cisco 890 Series, page A-21
All Models Except Cisco 860VAE Series
Table A-7 lists the system specifications for all models except the Cisco 860VAE series routers.
A-13
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Table A-7 Router Specifications
Description
Design Specification
(all models except
Cisco 860VAE series)
Physical Dimensions
Dimensions with antenna and rubber
feet (H x W x D)
1.9 x 12.8 x 10.4 in.
Weight (not including desktop power
supply)
5.5 lb (2.5 kg), maximum
Environmental Operating Ranges
Nonoperating temperature –4 to 149°F (–20 to 65°C)
Nonoperating humidity 5 to 95% relative humidity
Nonoperating altitude 0 to 15,000 ft (4570 m)
Operating temperature 32 to 104°F (0 to 40°C)
Operating humidity 10 to 85% relative humidity
Operating altitude 0 to 10,000 ft (3000 m)
Acoustic
Acoustic: Sound Pressure
(Typical/Maximum) for single fan units
Low speed 31.4 dBa
High speed 44.1 dBa
Acoustic: Sound Power
(Typical/Maximum) for dual fan units
Low speed 38.9 dBA
High speed 51.7 dBa
Router Power Adapter
Input voltage 100 to 240 VAC Nominal
Input frequency 47 to 63 Hz
Power output 60 W, maximum
Output voltages +12 VDC
Inline Power-over-Ethernet Adapter
Input voltage 85 to 264 VAC
Input frequency 47 to 63 Hz
Power output 80 W, maximum
Output voltage –48 VDC
A-14
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Cisco 860VAE Series
Table A-8 lists the system specifications for the Cisco 860VAE series routers.
Table A-8 Router Specifications
Description
Design Specification
Cisco 860VAE series
Physical Dimensions
Dimensions with antenna and rubber
feet (H x W x D)
1.75 x 9.5 x 9 in.
Weight (not including desktop power
supply)
3.3 lb (1.5 kg)
The total weight depends on
customer-selected options.
Environmental Operating Ranges
Nonoperating temperature –4 to 149°F (–20 to 65°C)
Nonoperating humidity 5 to 95% relative humidity
Nonoperating altitude 0 to 15,000 ft (4570 m)
Operating temperature 32 to 104°F (0 to 40°C)
Operating humidity 10 to 85% relative humidity
Operating altitude 0 to 10,000 ft (3000 m)
Acoustic
Acoustic: Sound Pressure
(Typical/Maximum) for single fan units
N/A, no fan
Acoustic: Sound Power
(Typical/Maximum) for dual fan units
N/A, no fan
Router Power Adapter
Input voltage 100 to 240 VAC Nominal
Input frequency 47 to 63 Hz
Power output 30 W, maximum
Output voltages +12 VDC
Inline Power-over-Ethernet Adapter
Input voltage not supported
Input frequency
Power output
Output voltage
AC Adapter for Cisco 867VAE
AC Adapter PWR-30W-AC
Environmental Operating Ranges
Nonoperating temperature –40 to 85°C
Nonoperating humidity 10% to 95%, non condensing
A-15
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 Series
Table A-9 lists the system specifications for the Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and
Cisco 860VAE-POE-W-A-K9 series routers.
Operating temperature -5 to 45° C
Operating humidity 10% to 90%, non condensing
Table A-8 Router Specifications (continued)
Description
Design Specification
Cisco 860VAE series
Table A-9 Technical Specifications
Description Specification
Physical Dimensions
Enclosure 9.5 x 9 x 1.75 in. (W x D x H)
Storage Environment
Temperature -25 C to +70 C
Altitude 4570 m (15000 ft)
Humidity 5–95% Relative Humidity
Operating Environment
Temperature 0 C to +40 C
Altitude 3000 m (10000 ft)
Humidity 10–85% Relative Humidity
Maximum temperature of
enclosure surface
No higher than 70 C when the ambient
temperature is 40 C
Acoustic
Sound Pressure N/A—Convection cooled, no fan
Power Supply
External power supply C866VAE-W-E-K9, C867VAE-W-A-K9,
C867VAE-W-E-K9 models:
Input: 100–240 VAC, Frequency range
50–60 Hz
Output: 12 VDC, 2.5 A, 30 W
C867VAE-POE-W-A-K9 model:
Input: 100–240 VAC, Frequency range
50–60 Hz
Output: 12 VDC, 5 A, 60 W
Inline Power-over-Ethernet (PoE): C867VAE-POE-W-A-K9 Model Only
IEEE 802.3af compliant
Wireless LAN
A-16
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Cisco 870 Series
Table A-12 lists the system specifications for the Cisco 870 series routers.
Radio technology IEEE 802.11n draft 2.0 standard compliant.
Backward compatible with 802.11b/g.
Operating Frequency 2.4 GHz radio band
Bandwidth 20 MHz
Channels Country-specific:
America SKU(-W-A): Channels 1–11
Europe SKU(-W-E): Channels 1–13
Table A-9 Technical Specifications
Description Specification
Table A-10 Router Specifications
Description Design Specification
Physical Dimensions
H x W x D = 2.00 x 10.25
x 8.50 in. (50.8 mm x
260.4 mm x 215.9.9 mm)
(nonwireless models)
H x W x D = 2.00 x 10.25
x 9.13 in. (50.8 mm x
260.4 mm x 231.9 mm)
(wireless models with
antenna connectors,
excludes antennae)
Weight: 2.10 lb (0.954 kg)
maximum
Optional external PoE adapter dimensions
H x W x D = 1.13 x 4.00 x
10.25 in. (28.9 x 101.6 x
260.4 mm) (cables
included)
H x W x D = 1.13 x 4.00 x
4.25 in. (28.9 x 101.6 x
108 mm) (cables not
included)
Weight = 0.32 lb (0.143
kg)
Environmental Operating Ranges
Nonoperating temperature -4 to 149°F (-20 to 65°C)
Nonoperating humidity 5 to 95 percent relative
humidity (noncondensing)
A-17
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Cisco 880 Series
Table A-12 lists the system specifications for the Cisco 880 series routers.
Nonoperating altitude 0 to 15,000 ft (0 to 4570m)
Operating temperature 32 to 104°F (0 to 40°C)
Operating humidity 10 to 85%, relative humidity
(noncondensing)
Operating altitude 0 to 10,000 ft (0 to 3000m)
Power Supply
AC input voltage 100 to 240 VAC
Frequency 50 to 60 Hz
Maximum output power 26W
Output voltages 5 and 12V
Optional external Inline PoE adapter
specifications
802.3af compliant (Mid-span
power delivered via pins 4,5,7
& 8)
AC Input Voltage 100 to 240 VAC
Frequency 50 to 60 Hz
AC Input Current 1A maximum
Maximum output power 80W
Output voltage 48 VDC
Table A-10 Router Specifications (continued)
Description Design Specification
A-18
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Table A-11 Router Specifications
Description Design Specification
Physical Dimensions
Nonwireless models (H x W x D):
1.9 x 12.8 x 9.8 in. (48 x 325 x 249 mm)
(includes rubber feet)
1.75 x 12.8 x 9.8 in. (44 x 325 x 249 mm)
(without rubber feet)
Wireless models (H x W x D):
1.9 x 12.8 x 10.4 in. (48 x 325 x 264 mm)
(includes rubber feet)
1.75 x 12.8 x 10.4 in. (44 x 325 x 264 mm)
(without rubber feet; excludes antennas)
Weight: 5.5 lb (2.5 kg) maximum
External Power Supply
Universal 100 to 240 VAC input; 60W, 12 VDC
output
Router Power Specifications
AC input voltage 100 to 240 VAC
Frequency 50 to 60 Hz
Maximum output power 60W
Output voltages 12 VDC
Optional internal PoE with
external adapter
Maximum output power 80W
External output voltage 48 VDC
Environmental Operating
Ranges
Nonoperating temperature -4 to 149°F (-20 to 65°C)
Nonoperating humidity 5 to 95% relative humidity (noncondensing)
Nonoperating altitude 0 to 15,000 ft (0 to 4570m)
Operating temperature
At sea level: 32 to 104°F (0 to 40°C)
Up 10,000 ft: 32 to 77°F (0 to 25°C)
Derating 2.7°F/10000 ft (1.5°C/1000 ft)
Operating humidity 10 to 85% relative humidity (noncondensing)
Operating altitude 0 to 10,000 ft (0 to 3000m)
A-19
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Cisco 880G Series 3G Wireless Integrated Services Router
Table A-12 lists the system specifications for the Cisco 880G series 3G Wireless Integrated Services
routers.
Cisco 880VA Series
Table A-12 lists the system specifications for the Cisco 880VA series routers.
Table A-12 Router Specifications
Description Design Specification
Physical Dimensions
Nonwireless models
H x W X D = 1.9 x 12.8 x
9.8 in. (48 x 325 x 249
mm) (includes rubber feet)
H x W X D = 1.75 x 12.8 x
9.8 in. (44 x 325 x 249
mm) (without rubber feet)
Weight: 5.5 lb (2.5 kg)
maximum
Environmental Operating Ranges
Nonoperating temperature -4 to 149°F (-20 to 65°C)
Nonoperating humidity 5 to 95 percent relative
humidity (noncondensing)
Nonoperating altitude 0 to 15,000 ft (0 to 4570m)
Operating temperature 32 to 104°F (0 to 40°C)
Operating humidity 10 to 85%, relative humidity
(noncondensing)
Operating altitude 0 to 10,000 ft (0 to 3,000m)
Power Supply
External Power Supply Universal 100- to 240-VAC
input; 60W, 12-VDC output
Router Power Specifications
AC Input voltage 100 to 240 VAC
Input frequency 50 to 60 Hz
Power output 60W
Output voltages 12 VDC
Optional internal PoE with external
adapter
Maximum output power 80W
Output voltage, external 48 VDC
A-20
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Table A-13 Router Specifications
Description Design Specification
Physical Dimensions
Nonwireless models:
H x W x D = 1.9 x 12.8 x 9.8 in. (48
x 325 x 249 mm) (includes rubber
feet)
H x W x D = 1.75 x 12.8 x 9.8 in. (44
x 325 x 249 mm) (without rubber
feet)
Wireless models:
H x W x D = 1.9 x 12.8 x 10.4 in. (48
x 325 x 264 mm) (includes rubber
feet)
H x W x D = 1.75 x 12.8 x 10.4 in. (44
x 325 x 264 mm) (without rubber
feet; excludes antennas)
Weight: 5.5 lb (2.5 kg) maximum
Environmental Operating Ranges
Nonoperating temperature -4 to 149°F (-20 to 65°C)
Nonoperating humidity 5 to 95% relative humidity
(noncondensing)
Nonoperating altitude 0 to 15,000 ft (0 to 4570m)
Operating temperature
At sea level: 32 to 104°F (0 to 40°C)
Up 10,000ft: 32 to 77 °F (0 to 25°C)
Derating 2.7°F/10000 ft (1.5°C
[304.8m])
Operating humidity 10 to 85% relative humidity
(noncondensing)
Operating altitude 0 to 10,000 ft (0 to 3000m)
Power Supply
AC input voltage 100 to 240 VAC
Frequency 50 to 60 Hz
Maximum output power 60W
Output voltages 12 VDC
Optional internal PoE with
external adapter
Maximum output power: 80W
External output voltage: 48 VDC
A-21
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Cisco 890 Series
Table A-12 lists the system specifications for the Cisco 890 series routers.
Table A-14 Router Specifications
Description Design Specification
Physical Dimensions
Cisco 891, 892, and 892F Nonwireless models:
H x W x D = 1.9 x 12.8 x 9.8 in. (4.8 x
32.5 x 24.9 cm) (includes rubber feet)
H x W x D = 1.75 x 12.8 x 9.8 in. (4.5 x
32.5 x 24.9 cm) (without rubber feet)
Wireless models:
H x W x D = 1.9 x 12.8 x 10.4 in. (4.8 x
32.5 x 26.4 cm) (includes rubber feet)
H x W x D = 1.75 x 12.8 x 10.4 in. (4.5
x 32.5 x 26.4 cm) (without rubber feet;
excludes antennas)
Weight: 5.5 lb (2.5 kg) maximum
Cisco 892FSP, 896VA, 897VA,
898EA and 891F
H x W x D =1.82 x 12.71 x 9.78 in. (4.62
x 32.28 x 24.84 cm) (includes rubber
feet)
H x W x D = 1.75 x 12.71 x 9.78 in.
(4.45 x 32.28 x 24.84 cm) (without
rubber feet)
Environmental Operating Ranges
Nonoperating temperature -4 to 149°F (-0 to 65°C)
Nonoperating humidity 5 to 95% relative humidity (noncondensing)
Nonoperating altitude 0 to 15,000 ft (0 to 4570m)
Operating temperature 32 to 104°F (0 to 40°C)
Operating humidity 10 to 85% relative humidity
(noncondensing)
Operating altitude 0 to 10,000 ft (0 to 3000m)
Power Supply
External Power Supply
AC input voltage Universal 100 to 240 VAC
Frequency 50 to 60 Hz
Maximum output power 60W
Output voltages 12 VDC
A-22
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Power Supply
Table A-15 lists the maximum input values for the power supply used with the Cisco 860, 880, 890 series
ISRs.
Wireless Access Point
Table A-16 lists the specifications for the wireless access point (AP).
Optional POE
Separate 80W POE power supply for
Cisco 891 and 892 ISRs
Single 125W power supply required for
Cisco 896, 897, 898 and 891F for router
and PoE
External output voltage 48 VDC
Table A-14 Router Specifications (continued)
Description Design Specification
Table A-15 Maximum Input Values for the power supply used with Cisco 860, 880, 890 series ISRs
Power Supply Unit 100 Volt 240 Volt
30 W 1 Ampere 0.5 Ampere
60 W 1.5 Ampere 0.7 Ampere
Table A-16 Wireless Access Point Specifications
Description Design Specification
Radio technology IEEE 802.11n draft 2.0 standard compliant. 2x3
MIMO
1
radio. Backward compatible with
802.11b/g and 802.11a (Cisco 890 series routers).
1. MIMO = Multiple Input/Multiple Output.
Operating frequency
Cisco 860 series and 880 series ISRs
2.4-GHz radio band
Cisco 890 series ISRs
2.4 and 5-GH radio bands
Channels Country-specific 20 and 40 MHz
PHY Data rate 802.11b up to 11 Mb/s
802.11g up to 54 Mb/s
802.11n up to 300 Mb/s
A-23
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
FE and GE Port Pinouts
Table A-17 describes the RJ-45 connector pinouts for Fast Ethernet (FE) ports with Power over Ethernet
(PoE). Some models support PoE using an optional module, and some models do not support PoE. For
ports that do not support PoE, pins 4, 5, 7, and 8 are not connected.
Cisco 860VAE and 860VAE-K9 ISRs do not support PoE.
Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant
devices connected to FE ports 0 and 1.
Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant
devices connected to FE ports 0, 1, 2, and 3.
Table A-18 describes the RJ-45 connector pinouts for the Gigabit Ethernet (GE) ports of the Cisco
860VAE and 860VAE-K9 ISRs.
Table A-17 Ethernet FE LAN Port Pinouts
Pin Function
1RX+
1
1. RX = Receive
2RX
3TX+
2
2. TX = Transmit
4 PoE—optional
5 PoE—optional
6TX
7 PoE—optional
8 PoE—optional
Table A-18 Ethernet GE Port Pinouts
Pin
GE Signal
(LAN and WAN)
1Tx A+
1
1. TX = Transmit
2Tx A-
3Rx B+
2
2. RX = Receive
4Tx C+
5Tx C-
6Rx B-
7Rx D+
8Rx D-
A-24
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Console and Auxiliary Port Connector Pinouts
Table A-19 lists the pinouts for the console and auxiliary port connectors.
FXS and FXO Port Connector Pinouts
Table A-20 lists the FXS and FXO connector pinouts.
VDSL2 Port Connector Pinouts
Table A-21 lists the VDSL2 connector pinouts.
Table A-19 Console and Auxiliary Port Connector Pinouts
RJ-45 Pin Function
1RTS
2DTR
3TXD
4 GND
5 GND
6RXD
7DSR
8CTS
Table A-20 FXS and FXO Connector Pinouts (RJ-11-to-RJ-45)
Pin Signal
1NC
2NC
3TIP
4RING
5NC
6NC
Table A-21 VDSL2 Connector Pinouts (RJ-11-to-RJ-45)
RJ-11 Pin Function
1Unused
2Unused
3TIP
4RING
A-25
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
ADSL2+ Port Connector Pinouts
Table A-22 lists the ADSL2+ connector pinouts.
V.92 Port Connector Pinouts
Table A-23 lists the V.92 connector pinouts.
G.SHDSL Port Connector Pinouts
Table A-24 lists the pinouts for the symmetrical high-speed DSL (G.SHDSL) WAN port for two-pair
products, including the following router model(s):
C888
5Unused
6Unused
Table A-21 VDSL2 Connector Pinouts (RJ-11-to-RJ-45) (continued)
RJ-11 Pin Function
Table A-22 ADSL2+ Connector Pinouts (RJ-11)
RJ-11 Pin Function
1Unused
2Unused
3TIP
4RING
5Unused
6Unused
Table A-23 V.92 Connector Pinouts (RJ-11-to-RJ-45)
RJ-11 Pin Function
1Unused
2Unused
3TIP
4RING
5Unused
6Unused
A-26
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Table A-25 lists the pinouts for the symmetrical high-speed DSL (G.SHDSL) WAN port for four-pair
products, including the following router models:
C888E
C888EW
C888EA
Data BRI Port Connector Pinouts
Table A-26 lists the pinouts for the Data BRI port.
Table A-24 G.SHDSL WAN Port Pinouts for Two-Pair Products
Pin Function
1Unused
2 TIP (Port1)
3 TIP (Port0)
4 RING (Port0)
5 RING (Port1)
6Unused
Table A-25 G.SHDSL WAN Port Pinouts for Four-Pair Products
Pin Function
1 TIP (Port1)
2 RING (Port1)
3 TIP (Port2)
4 TIP (Port0)
5 RING (Port0)
6 RING (Port2)
7 TIP (Port3)
8 RING (Port3)
Table A-26 Data BRI Port Pinouts
Pin Function
1Unused
2Unused
3TXP
4RXP
5TXN
6TXN
A-27
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Voice ISDN BRI Interface Pin Numbers and Functions
Table A-27 lists the interface pin numbers and functions for the voice ISDN BRI port.
SFP Port Connector Pinouts
Table A-28 lists the pinouts for the SFP port.
7Unused
8Unused
Table A-26 Data BRI Port Pinouts (continued)
Pin Function
Table A-27 Interface Pin Numbers and Functions
ISDN BRI NT/TE Card NT Interface
1
1. Use a straight-through cable for NT interfaces.
TE Interface
2
2. Use a crossover cable for TE interfaces.
Pin 3/T+ Pin 3/R+ Pin 3/T+
Pin 4/R+ Pin 4/T+ Pin 4/R+
Pin 5/R- Pin 5/T- Pin 5/R-
Pin 6/T- Pin 6/R- Pin 6/T-
Table A-28 SFP Port Pinouts
Pin Function
1 TX Ground
2TX Fault
3TX disable
4 Module definition 2
5 Module definition 1
6 Module definition 0
7 Rate Select
8 Loss of signal
9 Receiver ground
10 Receiver ground
11 Receiver ground
12 Inverted received data out
13 Received data out
14 Receiver ground
15 Receiver power
A-28
Cisco Integrated Services Router Hardware Installation Guide
Appendix A Technical Specifications
Cisco 860, 880, 890 Series
Cable Specifications
This section provides specifications for the following Ethernet cables:
Straight-through cable
Crossover cable
Because of the autocrossover (autosensing) function, both straight-through and crossover cables can be
used for the Ethernet LAN port.
Ethernet Cable Specifications
Table A-29 lists the specifications that apply to both straight-through and crossover Ethernet cables.
Maximum Cable Length
The maximum length for the Ethernet cables that connect equipment to the router is 328 feet
(100 meters). This length is also the maximum distance between the router and the equipment connected
to it.
16 Transmitter power
17 Transmitter ground
18 Transmit data in
19 Inverted transmit data in
20 Transmitter ground
Table A-28 SFP Port Pinouts (continued)
Pin Function
Table A-29 Ethernet Cable Specifications
Type Category
10BASE-T Category 3 or 5
100BASE-T Category 5 or higher
1000BASE-T Category 5 or higher
305

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Cisco C881 series wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info