Bedienungsanleitung Citizen Cal B110 (Seite 12 von 14) (Englisch)

553504

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

10. ALL-RESET

The display of this watch may not read correctly as a result of being subjected

to the effects of static electricity or strong impact and so forth. When this

happens, perform the procedure described in section "11. REFERENCE POSITION

ALIGNMENT" after performing the all-reset procedure described below.

1. Pull out the crown to the second click.

• The second hand moves to the 0-position stored in memory and stops.

2. Continuously press button A for at least 1 second.

• The second and hour hands perform a demonstration movement (forward

movement backward movement ---> forward movement). This completes the all-

reset procedure. Always make sure to perform the reference position

alignment procedure after performing all-reset.

Note:

Demonstration movement is not performed when the watch is insufficiently

charged. Perform the all-reset procedure only after charging the watch

sufficiently.

11. REFERENCE POSITION ALIGNMENT

After performing the all-reset procedure, align the second and minute hands at

their reference positions by pulling out the crown to the second click, and the

hour hand and date to their reference positions by pulling out the crown to the

first click.

1. Align the second and minute hands at the 12:00 position with the crown pulled

out to the second click.

• Turning the crown to the right moves the second and minute hands forward.

• Turning the crown to the left moves the second and minute hands backward.

• Turning the crown continuously causes the hands to advance rapidly. Turn

the crown to the left or right to stop the hands from advancing rapidly.

Note 1:

It takes about 1 second for the watch to store the reference position

in memory. Once the reference position has been stored in memory, the second

hand will begin irregular two-second interval movement. The reference position

may not be stored in memory if the crown is operated before the start of

irregular two-second interval movement after returning the crown to the normal

position.

Note 2:

The second hand will continue to remain stopped even if the crown is

returned to the normal position unless the reference position alignment

procedure is performed.

6. After performing the reference position alignment procedure, properly reset

the time and date.

• The watch shows 12:00 AM for the time of reference position alignment after

the all-reset procedure has been performed. Set the time and date by

referring to section

"4. SETTING THE TIME AND DATE”

, while being careful

not to incorrectly set AM and PM.

1. Align the date between the 31st and 1st

and the hour hand at the 12:00 position

with the crown pulled out to the first

click.

• Turning the crown to the right causes

the hour hand to move forward.

• Turning the crown to the left causes

the hour hand to move backward.

2. The date moves with the hour hand.

Continuously move the hour hand to set the

date between the 31st and 1st.

3. Align the hour hand at 12:00.

4. After each hand and the date have been

set, return the crown to the normal

osition.

Return to Table of Contents

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Citizen Cal B110 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Citizen Cal B110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info