Bedienungsanleitung Citronic CE22 (Seite 3 von 4) (Englisch)

455914

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

What is an Enhancer or Exciter

An Audio Enhancer is a multi-band processor which focuses selected high frequencies and applies specific filtering

to isolate and boost them without introducing other unwanted high frequencies, thus giving more “sparkle” and

“liveliness” to the signal. An Audio Exciter is a processor which actively replaces missing high frequencies by

actively generating overtones based on the existing frequencies to introduce more dramatic and yet more synthetic,

high frequency content.

The Bass Processor on each channel is a device which improves phase-alignment and focus of low frequencies,

giving similar attention to the bass as the Enhancer/Exciter does for the higher frequencies.

The SURROUND PROCESSOR varies phase-alignment between CH A and CH B to give the listener the

impression that the sound is coming from increasingly different directions. This has the effect of a virtual widening of

the stereo field when CH A and CH B are used to process the left and right channels of a mix.

Connection

The unit can be used in 2 configurations…

1. As 2 independent mono graphic enhancer/exciters – e.g. for 2 separate microphones on channel inserts

2. As a stereo left & right processor – e.g. as a main L+R enhancer/exciter on master inserts or between the

mixer and amplifier or recording equipment

Before connecting to an amplifier or other equipment, turn down all volume controls to avoid loud noises which may

cause damage to other equipment. Always switch amplifier power on last in line with volume levels down. Use good

quality 6.3mm jack or XLR signal leads to connect the enhancer/exciter to allied equipment. Connect mains power

via the IEC (ensuring lead is in good condition and the voltage selector is same as the supply voltage) and switch

the POWER on.

Operation

Begin with LOW MIX, HIGH MIX and SURROUND controls set fully down (anti-clockwise)

Set the TUNE control to the desired range of frequencies to be affected – 1kHz is Mid frequencies and 8kHz is High

Begin with the PROCESS control in the centre position (equal amounts of each process)

Gradually increase HIGH MIX and check the difference in high frequency content until the desired effect is reached

Varying the TUNE control at this stage will sweep the effect through the various frequencies.

If the process sounds too dramatic or unnatural, turn the PROCESS control toward ENHANCER.

If the process is too mild or ineffective, turn the PROCESS control toward EXCITER

To process bass, switch the BASS PROCESSOR “IN/OUT” button to IN and the respective “IN” LED will light.

Select the MODE – SOFT suits classical and subtle music content, TIGHT suits high energy dance music

Pressing IN/OUT gives a comparison of the signal with and without the BASS PROCESSOR.

To expand the perceived stereo field, press IN/OUT until the indicator is lit and gradually increase the rotary control

Use the IN/OUT switch to compare the effected and unaffected signal until the desired amount of process is set.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Citronic CE22 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info