Bedienungsanleitung Citronic PD-1s mk3 (Seite 3 von 4) (Englisch)

455898

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Assembly Instructions

1. Remove the main unit with the packing from the box and take off

the packing.

2. Insert the 45-rpm adaptor in the slot on the turntable.

3. Place the turntable platter onto the center spindle.

4. Place the slip mat on the platter.

5. Installation of cartridge:

When installing a cartridge, refer to the operating instructions of

that cartridge.

During installation, attach the stylus protector to guard the stylus

tip from damage.

6. Insert the headshell into the front end of the tonearm, then turn

the lock nut clockwise with the headshell firmly held horizontally.

7. Slide counterweight onto tonearm.

Twist it lightly and it will screw onto the rear shaft of the

tonearm.

8. Adjustment of horizontal zero (0) balance and stylus pressure:

(a) Remove the stylus protector, do not touch the stylus tip

during the adjustment.

(b) Set the cueing lever to the lower position.

rest to free it.

(d) While holding the Headshell lever rotate the counterweight

until the tonearm is approximately balanced horizontally

(floats freely).

(e) Refasten the tonearm with the arm clamp.

(f) Hold the counterweight stationary with one hand and rotate

only the stylus-pressure ring to bring the number “0” of the

ing into alignment with the center line on the tonearm rear

shaft.

(g) otate the counterweight clockwise until the scale shows the

value corresponding to the pressure of the used stylus,

typically 4 grams.

9. Set the anti-skating control knob to the same value as the stylus

pressure.

10. Install the dust cover to the main unit.

Placement

• Do not place the unit in a location where it will be exposed to direct

sunlight or near a heating appliance.

• Do not place the unit in a location where there is high humidity or

a lot of dust.

• Cartridge may pick up sound pressures or vibrations from the

speakers coming along the floor or through the air resulting in

howling. Find a location, which is very stable, and vibration free.

• The legs have functions for adjusting the height of the unit itself.

Adjust the legs to stabilize the main body horizontally.

Connections

1. Connect the power cord to the household AC outlet.

2. Connect the unit output terminals to the PHONO inputs of your

mixer.

Output terminals Mixer input

L White) >> L Channel

R (Red) >> R Channel

GND (Spade) >> GND

NOTE: Be sure to connect the separate ground terminal firmly to the

Mixer. If this connection is not made or is loose, a power source “HUM”

will result.

Scratch Mixing Tip

If you are using the deck for scratching the cartridge can be adjusted

to give better traction as follows:

Align the cartridge in a direct line to the back of the tone arm.

NOTE: this is not advisable to use during normal play.

Operation

The following instructions assume that the counter balance weight has

been set.

1. Rotate the power switch to turn on the power, the speed indicator

and the strobe-illuminator will light up.

2. Place a record on the slip mat, when playing a 45rpm record with a

large center hole; place the 45-rpm adaptor on the center spindle.

3. Set the speed to match the record.

4. Remove the stylus protector, release the arm clamp.

5. Set the cueing lever to the up position.

6. Press the Start/Stop button, the turntable platter will start to

rotate.

7. Move the tonearm over the desired groove.

8. Set the cueing lever to the down position, the tonearm will

descend slowly onto the record and play begins.

9. When play is finished, raise the cueing lever, move the tonearm to

the arm rest, secure the tonearm with the arm clamp.

10. Press the Start/Stop button to stop the platter rotating, push the

power button to turn off the power.

Suspend play

Set the cueing lever to “UP” position during play, the stylus tip of

the cartridge will be lifted from the record.

Target light

This unit is provided with a target light for illuminating the stylus

tip during play. Push the target light button, the target light will

be raised into position for illuminating the stylus tip.

Remote Start

The remote start jack socket is located at the rear of the deck. When

a jack plug is inserted and connected to a compatible mixer. The deck

will be able to be started automatically from the mixer remote start

control.

Changing the Speed

As long as the pitch control (13) is in center click position, the turntable

is operated with quartz- controlled speed.

The Blue LED (12) will then be lit.

The speed can be increased or decreased by 10% via the pitch control

(13). The Blue LED (12) will then be off.

The Trim control (15) can be used to provide an increased range of pitch

control adjustment in order to have the turntable rotate extremely slow

or fast.

For DJ Mixer operation, the start/stop function can be remotely

controlled by a separate switch. Use the jack remote socket (9) to

connect this to the mixer option.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Citronic PD-1s mk3 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info