Bedienungsanleitung Clarion CJ-981E (Seite 8 von 15) (Englisch)

473648

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

10 CJ-981E

English

Setting the Screen Saver

TIMER Function

In order to avoid forgetting to turn off the screen

in “CAM” mode, a timer function can be set to

automatically turn off the image after a set time.

∗ Default value is “5M” (five minutes).

1. Press the [FUNC] button and switch to the

“CAM” mode.

2. Press the [MODE] button to display the

“TIMER” setting menu.

Each time the [MODE] button is pressed the

menu switches alternately in the order

“CAM” ➜ “MARKER” ➜ … “TIMER” … ➜

“CAM”.

3. Use the [z] and [w] buttons to move the

cursor and highlight the desired timer value.

TIMER

OFF

4. Press the [MODE] button to return to the

“CAM” mode screen.

• After setting the timer, a numeral will

appear in the upper right corner of the

“CAM” mode screen to indicate the

number of minutes until the screen turns

off (5 ➜ 4 ➜ 3 ➜ 2 ➜ 1). Also, when the

countdown time reaches ten seconds, the

remaining time numeral “1” will flash.

Notes:

The automatic screen saver timer OFF does not

operate under the following conditions:

• When the transmission is placed in reverse gear

so that the rear-view camera image is displayed.

• When a video (VTR) image is being viewed from

the video input connector.

• When menu screens are displayed. (After one of

the above operations is performed, the “CAM”

mode timer is reset, and restarts from the newly

reset time.)

Setting the Camera Linked-

Image Switch (CAM AUTO/

CAM HAZARD)

°Automatic linked display

This setting is used to select whether the

camera image is automatically displayed when

the vehicle’s transmission is switched into

reverse gear or linked to the turn signal

circuit.

∗ Default setting is “ON” (linked display).

°Hazard switch linked display

This setting is used to select whether the

camera image linked to the turn signal circuit

automatically appears when the vehicle’s

hazard switch is engaged.

∗ Default setting is “ON” (no linked display).

1. Press the [FUNC] button to switch to the

“CAM” mode screen.

2. Press the [MODE] button to switch to the

“CAM1 AUTO” menu.

Each time the [MODE] button is pressed the

menu switches alternately in the order

“CAM” ➜ “MARKER” ➜ … “CAM1 AUTO” ➜

“CAM2 AUTO” ➜ “CAM3 AUTO” ➜ “CAM2

HAZARD” ➜ “CAM3 HAZARD” ➜ “CAM”.

CAM1

AUTO

OFF

Automatic linked display setting

• Linked switching with reverse gear (CAM1

AUTO)

This setting determines whether the

CAMERA1 image signal is automatically

displayed whenever the transmission is

shifted into reverse (when the power supply

box’s CAMERA1 link wire has been wired to

the reverse gear signal).

• Turn-signal linked display (CAM2 AUTO/

CAM3 AUTO)

This setting determines whether the

CAMERA2 or CAMERA3 image signal is

automatically displayed when the turn signals

are used (when the power supply box’s

CAMERA2 or CAMERA3 link wire has been

wired to the turn signal circuit)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clarion CJ-981E Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info