Bedienungsanleitung Clarion CX501E (Seite 21 von 32) (Englisch)

473621

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English

21 CX501E

Operations Common to Each Mode

● Setting the contrast

You can adjust the display contrast to match the

angle of installation of the unit.

∗ The factory default setting is “10”.

(Adjustment level: 1 to 16)

2-1. Select “CONTRAST”.

3-1. Turn the [ROTARY] knob to adjust the

contrast.

● Setting the button illumination

2-1. Select “COLOR”.

3-1. Turn the [ROTARY] knob to select the

color type.

• Setting COLOR SCAN mode

As selecting “CLR SCAN”, the color

automatically changes.

∗ The factory default setting is “CLR SCAN”.

∗ After 3 seconds the color changes to the other.

• Setting USER mode

The factory default setting is “RED 8” (red),

“GREEN 8” (green), “BLUE 8” (blue).

As selecting “USER COLOR 1, 2, 3”, press the

[ROTARY] knob to enter the setting.

1. Press the [x] or [v] to select “RED”,

“GREEN” or “BLUE”.

2. Turn the [ROTARY] knob to select from 0 to

3. Press and hold the [ROTARY] knob for

2 seconds or longer to store the color in

memory and cancel the setting mode.

● Setting the anti-theft function (CATS)

“CATS” is the acronym of “Clarion Anti-Theft

System”. When you set a PIN code (called as

“Personal Code”), a theft is prevented by

disabling the operation of the unit at the theft.

• Setting your Personal Code

2-1. Select “CODE”.

3-1. Press the [ROTARY] knob.

The set personal code screen appears.

4-1. Press the [DIRECT] buttons [1]-[6] to enter

your desired 4-digit Personal Code.

5-1. Press and hold the [ROTARY] knob

(2 sec.).

The entered Personal Code will be set, and

it will return to the previous screen.

Note:

• Write down your Personal Code in case you

forget it.

•

Erasing the Personal Code

2-1. Select “CODE”.

3-1. Press the [ROTARY] knob.

The ERASE PERSONAL CODE screen

appears.

4-1. Enter the Personal Code currently.

5-1. Press and hold the [ROTARY] knob

(2 sec.) or longer.

Entering a Personal Code mode is

cancelled.

• When the ENTER PERSONAL CODE

screen appears

The ENTER PERSONAL CODE screen will be

displayed when turning the ACC power on after

performing the following operations:

• The car battery was replaced.

• The backup power was cut off.

• The [RESET] button was pressed.

Note:

• If you have lost your Personal Code, please

contact Clarion customer service.

1. Enter your Personal Code currently set.

2. When the correct Personal Code is entered,

the unit will restart from the initial startup

screen.

To change adjustment setting

1. Press and hold the [DISP] button (1 sec.)

to switch to the adjustment selection

display.

2. Press the [x] or [v] button to select

the “item name”.

“CONTRAST” ↔ “COLOR” ↔ “CODE” ↔

“SCRN SVR” ↔ “SCROLL” ↔

“DIMMER” ↔ “BLINKLED” ↔

“REAR/S-W” ↔ “INT-SW” ↔ “RESET”

3. Turn the [ROTARY] knob to select the

“desired setting value”.

∗ In the case of display blinking “ENT”, you

can press the [ROTARY] knob to adjust the

setting value.

∗ After completing settings, press the [DISP]

button to return to the previous mode.

CX501E_EN.book Page 21 Thursday, November 11, 2010 1:16 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clarion CX501E Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Clarion CX501E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info