Bedienungsanleitung Clarion CZ703E (Seite 6 von 20) (Englisch)

580420

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

English

CZ703E

Handling Discs

Handling

• New discs may have some roughness

around the edges. If such discs are used,

the player may not work or the sound may

skip. Use a ball-point pen or the like to

remove any roughness from the edge of

the disc.

• Never stick labels on the surface of the disc

or mark the surface with a pencil or pen.

• Never play a disc with any cellophane tape

or other glue on it or with peeling off marks.

If you try to play such a disc, you may not

be able to get it back out of the player or it

may damage the player.

• Do not use discs that have large scratches,

are misshapen, cracked, etc.

Use of such discs may cause misoperation

or damage.

• To remove a disc from its storage case,

press down on the center of the case and

lift the disc out, holding it carefully by the

edges.

• Do not use commercially available disc

protection sheets or discs equipped with

stabilizers, etc. These may damage the

disc or cause breakdown of the internal

mechanism.

Storage

• Do not expose discs to direct sunlight or

any heat source.

• Do not expose discs to excess humidity or

dust.

• Do not expose discs to direct heat from

heaters.

Cleaning

• To remove ngermarks and dust, use a soft

cloth and wipe in a straight line from the

center of the disc to the circumference.

• Do not use any solvents, such as

commercially available cleaners, anti-static

spray, or thinner to clean discs.

• After using special disc cleaner, let the disc

dry off well before playing it.

On Discs

• Never turn off the power and remove the

unit from the car with a disc loaded.

CAUTION

For your safety, the driver should not insert

or eject a disc while driving.

Ball-point pen

Roughness

4. CAUTIONS ON HANDLING

5. OPERATIONS

Basic Operations

Note:

• Refer to the diagrams in “3. CONTROLS”

when reading this chapter.

CAUTION

When the unit is turned on, starting and

stopping the engine with its volume

raised to the maximum level may harm

your hearing.

Be careful about adjusting the volume.

Power on / off

Notes:

• Start the engine before using this unit.

• Be careful about using this unit for a long

time without running the engine. If you

drain the car’s battery too far, you may not

be able to start the engine and this can

reduce the service life of the battery.

1. Start the engine. The power button / knob

illumination on the unit will light up.

Engine ON

position

2. When power on rst time, you can select

initial speaker system. (Refer to “Audio

Setup”)

• INITIAL …. When powering on the unit

for the rst time, you can select a speaker

system. Check your speaker system,

choose it on the unit, and then, set your

desired sound quality referring to “Audio

Setup”.

• LOAD …. When powering on the unit

for the rst time, “LOAD” is not selected.

When this unit is turned on for the rst

time, it allows you to select a speaker

system.

“NORMAL” …. FRONT 2ch / REAR 2ch /

SUBWOOFER 2ch

“2WAY” …. HIGH 2ch / MID 2ch / REAR

2ch

“3WAY” …. HIGH 2ch / MID 2ch /

SUBWOOFER 2ch

Note:

If you press the RESET button or

disconnect the back-up line after

completing the audio setup, “INITIAL /

LOAD” is displayed. In this case, the unit

functions as follows.

• INITIAL …. When powering on the

unit after RESET or the backup line is

disconnected, the audio setup in the

memory is cleared and you will need to

start from selecting a speaker system.

Choose your desirable speaker system

and set your desired sound quality

referring to “Audio Setup”.

• LOAD …. When powering on the

unit after RESET or the backup line is

disconnected, the preset speaker system

and other settings are called.

If you changed the speaker system, reset

from INITIAL.

3. Press the [SRC / ] button on the front

panel or the remote control to turn on the

power under standby mode. The unit goes

back to the last status after power on.

4. Press and hold the [SRC / ] button on

the front panel or the remote control to turn

off the power.

CT (Clock Time) display

• The displayed clock data is based on the

CT (clock time) data in the RDS signal.

Mute

Press the [MUTE] button on the remote

control to mute the volume from the unit.

Note:

Doing the operation above again or adjusting

volume will release muting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clarion CZ703E Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Clarion CZ703E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info