580541
12
Zoom out
Zoom in
Vorherige Seite
1/42
Nächste Seite
Basic Operations
English
12
DXZ578RUSB
Adjusting Sound Mode
Adjusting the subwoofer output
volume
You can adjust the volume output from the unit’s
subwoofer output terminal.
2-1. Select the “
S-W VOL
”.
3-1. Press the [
UP
] or [
DN
] button to change the
output volume.
The factory default setting is “
0
”.
(Setting range: +5 to –5)
Setting the Digital Z-Enhancer
This unit are provided with 3 types of sound
tone effects stored in memory. Select the one
you prefer.
The factory default setting is “
DZE OFF
”.
2-1. Select the “
DZE
”.
3-1. Press the [
UP
] or [
DN
] button to select the
tone effect. Each time you press the [
UP
]
or [
DN
] button, the tone effect changes in
the following order:
DZE OFF
DZE 1
DZE 2
DZE 3
DZE OFF
: no sound effect
DZE 1
: Suitable for genuine speakers
DZE 2
: Suitable for separate
speakers
DZE 3
: Suitable for co-axial speakers
3-2. When the “
DZE 1
”, “
DZE 2
” or “
DZE 3
” is
set, press the [ ] button. Then
press the [
UP
] or [
DN
] button to change the
DZE level from +3 to –3.
The factory default setting is “
0
”.
3-3. Press the [ ] button to return to the
previous mode.
Compensation
There is no need to compensate frequency
characteristics if they are flat (no peaks or
valleys) when you have measured the
frequency characteristics with a measuring
device. However, sometimes the frequency
characteristics rise or fall in some places. If this
happens, the frequency characteristics must be
compensated. Create a frequency curve having
characteristics that are opposite to the center
frequency of parts where the characteristics rise
and fall to cancel out these peaks and values,
and make the frequency characteristics as flat
as possible.
Making the frequency characteristics as flat as
possible is called “Compensation”.
Compensation of frequency
characteristics
The figure below shows the relationship
between the center frequency, gain and Q
curve.
To change sound mode
1. Press the [ ] button and select the sound
mode to adjust.
2. Push the [
SEEK PANEL
] leftward or
rightward to select the “item name”.
S-W VOL
DZE
BASS
TREBLES RESTORHPF
S-W LPFBALANCEFADER
3. Press the [UP] or [DN] button to select the
“desired setting value”.
In the case of display blinking “ENT”, you
can press the
[] button to adjust the
setting value.
BASS” and “TREBLE” can be adjusted
only when “DZE” is set to “DZE OFF” (page
12).
After completing settings, press the
[]
button to return to the previous mode.
Note:
During sound adjustment mode, if no
operation is performed for more than 10
seconds, this mode can be canceled and
return to the previous mode.
3dB
Q =
F
f
f
Center
Frequency (F)
Frequency
(Hz)
Q curve(Q)
Frequency
curve
Level
(dB)
Gain
DXZ578RUSB_EN.book 12 ページ 2006年12月26日 火曜日 午後2時49分
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Clarion DXZ578RUSB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info