Bedienungsanleitung Clarion DXZ588RUSB (Seite 14 von 328) (Englisch)

580431

Zoom out

Zoom in

Vorherige Seite

1/328

Nächste Seite

Basic Operations

English

14 DXZ588RUSB

Adjusting Sound Mode

● Adjusting the subwoofer output

volume

You can adjust the volume output from the unit’s

subwoofer output terminal.

2-1. Select the “S-W VOL”.

3-1. Press the [UP] or [DN] button to change the

output volume.

∗ The factory default setting is “0”.

(Setting range: +5 to –5)

● Setting the Digital Z-Enhancer

This unit are provided with 3 types of sound tone

effects stored in memory. Select the one you

prefer.

∗ The factory default setting is “DZE OFF”.

2-1. Select the “DZE”.

3-1. Press the [UP] or [DN] button to select the

tone effect. Each time you press the [UP] or

[DN] button, the tone effect changes in the

following order:

“DZE OFF” ↔ “DZE 1” ↔ “DZE 2” ↔

“DZE 3”

DZE OFF : no sound effect

DZE 1 : Suitable for genuine speakers

DZE 2 : Suitable for separate

speakers

DZE 3 : Suitable for co-axial speakers

3-2. When the “DZE 1”, “DZE 2” or “DZE 3” is

set, press the [ ] button. Then

press the [UP] or [DN] button to change the

DZE level from +3 to –3.

∗ The factory default setting is “0”.

3-3. Press the [ ] button to return to the

previous mode.

● Compensation

There is no need to compensate frequency

characteristics if they are flat (no peaks or

valleys) when you have measured the

frequency characteristics with a measuring

device. However, sometimes the frequency

characteristics rise or fall in some places. If this

happens, the frequency characteristics must be

compensated. Create a frequency curve having

characteristics that are opposite to the center

frequency of parts where the characteristics rise

and fall to cancel out these peaks and values,

and make the frequency characteristics as flat

as possible.

Making the frequency characteristics as flat as

possible is called “Compensation”.

● Compensation of frequency

characteristics

The figure below shows the relationship

between the center frequency, gain and Q

curve.

To change sound mode

1. Press the [ ] button and select the sound

mode to adjust.

2. Push the [SEEK PANEL] leftward or

rightward to select the “item name”.

“S-W VOL” ↔ “DZE” ↔ “BASS” ↔

“TREBLE” ↔ “S RESTOR” ↔ “HPF” ↔

“S-W LPF” ↔ “BALANCE” ↔ “FADER”

3. Press the [UP] or [DN] button to select the

“desired setting value”.

∗ In the case of display blinking “ENT”, you

can press the [] button to adjust the

setting value.

∗ “BASS” and “TREBLE” can be adjusted

only when “DZE” is set to “DZE OFF” (page

14).

∗ After completing settings, press the []

button to return to the previous mode.

Note:

•During sound adjustment mode, if no

operation is performed for more than 10

seconds, this mode can be canceled and

return to the previous mode.

3dB

Q =

Center

Frequency (F)

Frequency

(Hz)

Q curve(Q)

Frequency

curve

Level

(dB)

Gain

01_DXZ588RUSB_EN.book 14 ページ２００７年１１月２７日　火曜日　午後６時５分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clarion DXZ588RUSB Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info