Bedienungsanleitung Clarion nx509e (Seite 52 von 69) (Englisch, Französisch, Spanisch)

162957

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

NX509

English

Owner’s manual

❏ Setting the anti-theft function

(CATS)

“CATS” is the acronym of “Clarion Anti-Theft

System”. When you set a PIN code (called as

“Personal Code”), a theft is prevented by

disabling the operation of the unit at the theft.

In addition, set the Blink LED function to improve

the effect of the CATS function (see page 48).

Setting your Personal Code

Note:

• Write down your Personal Code in case you forget

it.

Erasing the Personal Code

When the ENTER PERSONAL CODE

screen appears

The Personal Code screen will be displayed

when turning the ACC power on after performing

the following operations:

• The car battery was replaced.

• The backup power was cut off.

• The Reset button was pressed.

Note:

• If you forgot your Personal Code, please consult

your dealer or an authorized Clarion service

center.

1. Enter your Personal Code currently set.

2. When the correct Personal Code is entered,

the unit will restart from the initial startup

screen.

Note:

• When you enter a wrong Personal Code, the

message “Code Incorrect” is displayed and the

Personal Code entry is prohibited for a while. This

prohibited time is changed according to the

number of times of wrong code entry as follows:

• 1 to 6 times: 15 seconds

• 7 times or more: 15 minutes

❏ Setting the Auto Antenna

When an auto antenna which is extended

automatically is used, you can set so that it is

automatically extended/collapsed according to

the power setting of this unit.

1. Touch the [SET] key to display the Settings

screen.

2. Touch and hold the [Auto] or [Down] key of

the Antenna item for more than 1 second to

set this function.

Auto:

The auto antenna function is turned on.

Down:

The antenna is collapsed.

3-1. Touch the [System] key to display the

System tab screen.

3-2. Touch the [}] key to display the next

screen.

3-3. Touch and hold the blank area just below

the []] key of the System Check item for

more than 2 seconds.

The Personal Code screen appears.

• When a Personal Code is already set, the

Erase Code screen will appear. Retry this

operation after erasing the old Personal

Code.

3-4. Enter your desired 4-digit Personal Code by

touching the [0] to [9] keys, then touch the

[ENT] key.

• Touch the [BS] key when you make a

mistake in entering.

3-5. Enter the same Personal Code again for

confirmation, then touch and hold the [ENT]

key for more than 2 seconds.

The entered Personal Code will be set, and

it will return to the previous screen.

3-1. Touch the [System] key to display the

System tab screen.

3-2. Touch the [}] key to display the next

screen.

3-3. Touch and hold the blank area below the []]

key of the System Check item for more than

2 seconds.

The Erase Code screen appears.

3-4. Enter the Personal Code currently set by

touching the [0] to [9] keys, then touch and

hold the [ENT] key for more than 2 seconds.

The message “Personal Code has been

erased” appears, and it will return to the

previous screen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clarion nx509e Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Clarion nx509e

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info