Bedienungsanleitung Clarion UG-2176A (Seite 2 von 2) (Englisch)

659139

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

NAMES AND FUNCTIONS OF PARTS

 Interface Box (Equipment) Front Panel

Calibration Indicator [CAL]

* The indicator will light up in green (for about 5 sec-

onds) during image capture.

UART terminal [DATA]

* Connect the serial cable.

RCA terminal [VIDEO]

* Connect the RCA cable.

 Interface Box (Equipment) Rear Panel

Power indicator [POWER]

* The indicator will light up in red when power is ON.

USB terminal [USB]

* Connect the USB cable.

Reset switch [RESET]

* This is used when resetting the equipment.

Use a thin rod to press the switch for two or

more seconds.

CAUTION

Do not use this equipment close to a mobile phone or wireless device.

The radio waves from the mobile phone or wireless device may result in noise

and malfunction.

OPERATING METHOD

 Start up the equipment.

Start up a notebook PC and install the software on the enclosed application

CD.

Connect the notebook PC and camera ECU to the equipment using the en-

closed cable.

When the USB cable is connected, power is supplied from the PC and the power

indicator lights up in red.

See the cabling instructions and connect the cables between the equipment cor-

rectly.

Advice

Start up the camera ECU.

Perform the operations with the application software installed in the notebook

PC.

See the application software manual in the notebook PC on how to use the appli-

cation software.

Advice

CAUTION

Do not supply power other than the USB bus power to the equipment.

This may result in fire and faults.

 Terminating this equipment

Check that access to the equipment and camera ECU has been stopped.

The checks to be conducted when access is stopped are as follows.

Check that the calibration indicator (green) has been turned off.

Check that serial communication in the application has been stopped.

Advice

Use the application software to disconnect the camera ECU from the equip-

ment.

See the application software manual in the notebook PC on the shutdown proce-

dure.

Advice

Disconnect the USB cable.

The power of the equipment goes OFF and the power indicator (red) goes off.

Disconnect the RCA cable and serial cable.

CAUTION

When disconnecting the USB cable, check that the calibration indicator (green)

goes off.

WIRING AND CONNECTIONS

 Preparations

Equipment Enclosed cables

Interface Box (Equipment) ...................... 1

Notebook PC (

see below for compatible OS)

...... 1

Camera ECU (Sold Separately) ................. 1

Car-mounted Camera (Sold Separately) .... 4

USB Cable ............................................. 1

RCA Cable ............................................ 1

Serial Cable ........................................... 1

* The notebook PC, camera ECU and car-mounted cameras are sold separately.

* Make sure only the enclosed cables are used.

Notebook PC Compatible OS / Display Resolution

Compatible OS

Windows 7

• Professional SP1 32 bit / 64 bit Japanese

version, 32 bit English version

Windows 8.1

• Pro 64 bit Japanese version

Display Resolution

• XGA (1024 x 768) & above

* Compatible OS are operating systems that have been internally verified to work normally. However, opera-

tions may differ depending on the type of PC and the application software installed in the PC.

 How to Connect the Cables

6 SurroundEye Interface Box

(Equipment)

Back Panel

Notebook PC

6 SurroundEye Interface Box

(Equipment) Front Panel

Camera ECU and

car-mounted camera

Connect to the RCA terminal [VIDEO]

3 RCA cable

4 Serial Cable

Connect to the RCA terminal [RCA connectors]

Connect to the UART terminal [4 connectors]

Connect to the UART terminal [DATA]

Connect to the USB port [USB]

* USB B MALE CONNECTER

Connecting to a USB port

* USB A MALE CONNECTER

2 USB cable

Yellow Green

Gray

Yellow

White

Camera

ECU

TROUBLESHOOTING

Please follow the following troubleshooting procedures in case of any problems.

Consult your dealer if you cannot resolve the issue on your own.

Symptom Reason Solution

There is no power.

The power indicator

is not lit.

The USB cable is

not connected cor-

rectly.

Please see the cabling instructions and

connect the cable correctly.

Image cannot be

captured in the note-

book PC.

The captured image

is distorted.

The RCA cable is

not connected cor-

rectly.

Please see the cabling instructions and

connect the cable correctly.

Serial communication

does not work.

The serial cable is

not connected cor-

rectly.

Please see the cabling instructions and

connect the cable correctly.

The application does

not work.

The various cables

are not connected

correctly.

Please see the cabling instructions and

connect the cable correctly.

The application does

not work.

The micro-computer

is malfunctioning

due to noise etc.

Use a thin rod to press the reset switch

for two or more seconds.

Start up the application again.

The equipment gets

abnormally hot.

The internal elec-

tronic parts may be

faulty.

Unplug the USB cable immediately,

switch off the power supply and con-

sult your dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clarion UG-2176A Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info