Bedienungsanleitung Clarion vzn709 (Seite 72 von 82) (Englisch)

162954

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

VZ709

English

INSTALLATION

MANUAL

Installation Precautions

CAUTION

• Do not install the system in the locations

described below. This may cause a fire,

accident or electrical shock:

A location exposed to rain or dust.

A location interfering with the driver’s

visual range or operation of the vehicle.

An unstable location, or where the system

may fall.

• Do not install this unit in a place exposed to

direct sunlight, heat or a place where the

vent holes or heat radiation holes are

covered.

• When you install the antenna, mount it in a

place where the elements of the antenna do

not protrude beyond the edge of the front,

back, left and right of the vehicle.

• If it comes in contact with pedestrians, it

may cause an accident.

Installation Notes

CAUTION

• Use only the supplied parts.

• If unspecified parts are used, they may

cause damage.

• Any holes made in the body of the vehicle

should be sealed with a silicon adhesive.

• If exhaust fumes or water penetrates into

the vehicle, this may cause an accident.

• Fasten the bolts securely when installing

the unit. If the bolts are loose an accident or

malfunction could occur.

Connection Notes

CAUTION

• Verify wires with a digital multi-meter prior

to making any connections. Many new

vehicles use multiplexed and/or low voltage

circuits that can be damaged if a test light

or logic probe is used.

• Connect cables appropriately. If a wrong

connection is made, this may cause a fire or

accident.

• When passing cables through the body of

the vehicle, use non-conductive grommets.

• If the coatings of the cables are worn out by

rubbing, this may cause an accident, fire or

a short circuit.

• After wiring cables, fix them with insulation

tape.

• Be sure to switch off the vehicle when

connecting or disconnecting cords to/from

the unit, otherwise an electric shock, injury

or accident may occur.

WARNING

• When installing the unit to a vehicle with

an airbag system, never install it in a

place where it may affect the operation of

the airbag.

• Do not install this unit in the following

locations:

A location interfering with the driver’s

visual range or operation.

A location where the gear shift or brake

pedal are hindered.

A location where passengers are at risk.

An unstable location, or where the

system may fall.

WARNING

• Please note the position of pipes, tanks

and electrical wirings before installing

the unit into the vehicle; failure in

avoiding these may cause a fire or

malfunction.

WARNING

• Loom all cables according to the

instruction manual, so as not to hinder

operation.

• Wire the connecting cords/cables away

from high temperature areas. If the

coatings of the cables melt, it could

cause an accident/fire by a short circuit.

Take care when wiring in the engine

compartment.

• When wiring the connecting cables in a

vehicle with an airbag system, never feed

the cables through a place where it may

affect the operation of the airbag.

• An airbag not operating correctly in an

emergency may cause increased injury.

280QC6832BA-VZ709_EN.book Page 70 Monday, January 5, 2009 5:48 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clarion vzn709 Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info