Bedienungsanleitung Clatronic BS 1279 (Seite 25 von 38) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

483815

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

ENGLISH

Symbols in these Instructions for Use

Important information for your safety is specially marked. It is

essential to comply with these instructions in order to avoid ac-

cidents and prevent damage to the machine:

WARNING:

This warns you of dangers to your health and indicates

possible injury risks.

CAUTION:

This refers to possible hazards to the machine or other

objects.

 NOTE: This highlights tips and information.

Special Safety Instructions

• Do not suck up liquids!

• Do not suck up hot ashes or pointed or sharp objects!

• Do not use the device in damp rooms!

• Never use without the lter. Check that the lter is inserted

correctly!

• Hair, clothing and body parts away from the vacuum nozzle

during use!

• Keep the vacuum cleaner away from sources of heat like

radiators, ovens, etc.!

Overview of the Components

1 Vacuum hose

2 Dust bag lling display

3 Carrying handle

4 Cable-winding key

5 On/off switch and continuous power regulator

6 Cable

7 Accessory compartment

(groove and brush nozzle)

8 Dust bag compartment

9 Handle for opening

the dust bag compartment

10 Floor nozzle (with hook (not shown))

11 Groove and brush nozzle (Accessories)

12 Telescopic suction tube

13 Air Slide

Start-up

• Insert the connection head of the suction hose into the hose

connector until it locks in place. To do so, please press the

buttons simultaneously. In order to release the hose again,

please press the buttons once more on the connection

head.

• Keep the buttons pressed down and then pull out the hose.

• Insert the vacuum tube into the handle if required.

• Then assemble the oor nozzle and/or the accessories.

Accessory Compartment (7)

The accessories (crevice and brush nozzle) are located in the

accessory compartment next to the cable duct.

Telescope Vacuum Pipe

The height-adjustable vacuum pipe enables

individual alignment to your height. Unlock the

coupling by pressing the key in the direction of the

arrow. Slide the vacuum pipe to the desired length.

To lock the device, release the key until you hear

it lock in place.

Using the Appliance

1. Unwind the length of cable you require.

CAUTION:

• Pull out the cable up to the maximum length indicated

with the yellow mark.

• Never pull the cable out up to the red mark as the

cable winding can be damaged.

 NOTE:

If the red mark is visible, pull in the cable with the help of

the cable winding button back to the yellow mark.

2. Insert the mains plug into a correctly installed 230 V, 50 Hz

power socket. Turn the device on by the on/off switch by

pressing down the button.

3. Set the “carpet/hard oor” switch, depending on the oor

covering.

4. Set the vacuum power with the vacuum power regulator

(Min to Max).

5. Vacuum at a steady speed. There is no need to exert pres-

sure.

 NOTE:

Pay attention to the range that can be covered with the cable

length!

Vacuum power regulator (5)

Low vacuum power: For curtains and delicate fabrics.

Medium vacuum power: For long-pile velour carpets and textile

ooring.

High vacuum power: For sturdy rugs and oors.

Air Slide (13)

Open the air slide on the hose handle in order to

regulate the airow or to clear any particles sticking

to the nozzle.

Switching off and Winding up the Mains Lead

1. Turn the vacuum cleaner off by the on/off switch and remove

the plug from the socket.

2. Keep the plug in your hand.

3. Press the cable winding button and guide the cable. Hold

the cable to avoid wrapping.

Nozzle Attachment

Crevice and

jointed nozzle: For vacuuming upholstery, curtains and in

corners and crevices etc.

 NOTE: „2-in-1“ nozzle:

When this is folded together it can be

used as a groove nozzle. If you would like

to use the brush nozzle, pull the brush

section in the direction of the arrow until it

locks in place.

Floor nozzle: To clean carpets or smooth surfaces.

Smooth oors: Press down the lever with

the brush symbol with your

foot. The brush is now vis-

ible.

Carpets: Press the lever n the oppo-

site direction. The brushes

are now retracted.

Releasing

the nozzles: Pull these off while turning slightly.

Maintenance

Dust bag replacement display (2)

Hold the hose up into air. If the dust bag change display lights

up, the bag is full. Please change it.

Changing the dust bag

• Pull the plug out of the socket.

• Open the lid of the dust bag compartment by the handle (9).

• Then remove the dust bag by pulling it upwards.

• Insert a new bag. Please ensure that the bag is located cor-

rectly in the guide mechanism. Press down the fastener with

the bag. The bag must be located completely in the dust bag

compartment. Close the cover so that it snaps into place.

Filter

Your appliance has two lters.

Motor protection ﬁlter (inlet ﬁlter):

The inlet lter is located in the dust bag compartment. The

lter is located vertically in the rear section of the dust housing.

Remove the lter by pulling upwards.

Cleaning the Filter Element

Clean the engine protection lter after 10 dust bag changes. If

necessary, the lter can also be washed in warm water without

any additives. Place it back into place only once it is completely

dry!

05-BS 1279.indd 25 17.08.2010 14:21:56 Uhr

Clatronic BS 1279 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info