Bedienungsanleitung Clatronic BS 1300 (Seite 31 von 54) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

653899

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Electrical connection

• Before connecting the plug to the wall socket, check wheth-

er the mains voltage is correct. Refer to the information on

the rating plate of the device.

• Connect the device to a certied wall socket only.

Using the Appliance

1. Insert the mains plug into a correctly installed power socket.

2. Turn the device on by the on/off switch by pressing down

the button.

3. Set the “carpet/hard oor” switch, depending on the oor

covering.

4. Vacuum at a steady speed. There is no need to exert pres-

sure.

NOTE:

Pay attention to the range that can be covered with the

cable length!

Air Slide

Open the air slide on the hose handle in order

to regulate the airow or to clear any particles

sticking to the nozzle.

Switching off and Winding up the Mains Lead

1. Turn the vacuum cleaner off by the on/off switch and

remove the plug from the socket.

2. Keep the plug in your hand.

3. Press the cable winding button and guide the cable. Hold

the cable to avoid wrapping.

Maintenance

Dust bag replacement display (10)

Hold the hose up into air. If the display for the vacuum bag

change shows “red”, the dust bag is full. Please change it.

Changing the dust bag

1. Pull the plug out of the socket.

2. Use the opener (13) to open the lid of the dust bag com-

partment.

NOTE:

The lid can be locked in upright position. Do not push the

lid beyond the locking mechanism! Otherwise the mount-

ing could break away.

3. Lift up and remove the dust bag holder. Remove the dust

bag by taking it from the holder.

4. Insert a new bag. Please ensure that the bag is located

correctly in the guide mechanism.

5. Insert the dust bag with the holder into the designated

slot. The bag must be located completely in the dust bag

compartment. Close the cover so that it snaps into place.

Filter

Your appliance has two lters.

Motor protection lter (inlet lter)

The inlet lter is located in the dust bag compartment. The

lter is located vertically in the rear section of the dust housing.

Remove the lter by pulling upwards.

Cleaning the Filter Element

Clean the engine protection lter after 10 dust bag changes. If

necessary, the lter can also be washed in warm water without

any additives. Place it back into place only once it is completely

dry!

Outlet lter (6)

The appliance is also equipped with an outlet lter.

It is located on the back of the device behind the cover.

1. Push the lever towards the left and remove the ventilation

grid.

2. Remove the lter insert and clean it as described above.

3. Once dried completely, reinstall the lter insert.

4. Ret the ventilation grid in the device. Pay attention to

the guide tabs. The ventilation grid must audibly click into

place.

Cleaning

WARNING:

• Before cleaning remove the mains lead from the socket.

• Under no circumstances should you immerse the device in water

for cleaning purposes. Otherwise this might result in an electric

shock or re.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic BS 1300 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info