Bedienungsanleitung Clatronic bss 1261 (Seite 37 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Norwegisch)

319587

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

D – Preparing for Wet Cleaning with the

Addition of Cleaning Agent

• Release the catches to separate the motor housing from the

collection container.

• Remove the dust bag and ensure that the container is

empty.

• Attach the motor protection ﬁ lter and place the motor

housing back on the collection container.

• Remove the inlet hose for the cleaning agent from the tank

(illustration D1).

• Remove the cleaning agent tank from the chassis (illustrati-

on D2).

• Use the measuring beaker to dose the cleaning agent for

the tank (illustration D3). Please use 3-5 measuring beakers

for 5 litres of water, depending on the level of soiling.

• First pour the cleaning agent into the tank (illustration D4).

• Then ﬁ ll the tank up to the maximum mark with cold water

(illustration D5).

• Reattach the tank to the chassis (illustration D6).

• Attach the inlet hose for the cleaning agent to the tank and

the motor housing (illustration D7).

• Assemble the trigger on the handle (illustration D8, D9).

• Use the clamps (4) to attach the inlet hose (8) to the suction

hose (illustration D10).

• Connect the inlet hose to the coupling of the motor housing

(illustration D11).

• The connection can be removed by pressing the coloured

button on the coupling and then pulling out the connection

(illustration D12).

• Attach the suction hose to the motor housing (illustration

D13).

• Attach the suction tube (illustration D16).

• Attach a washing nozzle to the suction tube (illustration

D14).

• In the case of smooth ﬂ oors you can also use the rubber lip

(illustration D15).

• Now connect the inlet hose for the cleaning agent to the

quick coupling on the trigger (illustration D17).

• Attach the inlet hose for the cleaning agent to the tube with

the clamps.

• The small washing nozzle can also be attached directly to

the handle (illustration D18, D19).

• Unwind the connection cable completely and insert the plug

into the socket (illustration D20).

E – Wet Cleaning of Textile Coverings,

Carpets and Smooth Floors

CAUTION:

• The pump must not run when dry! Do not turn the pump

on if the tank is empty.

• Always check the level of the liquid in the tank before use!

CAUTION:

Before you start cleaning!

• Always check the effect of the cleaning agent on an

inconspicuous section of the carpet.

Text Coverings with Slight Soiling

• Turn on both the “MOTOR” and “PUMP” buttons (illustration

E1, E2).

• Press the trigger to distribute the cleaning agent over the

surface (illustration E3).

• Release the trigger to interrupt the spraying of the cleaning

agent (illustration E4).

• Move the washing nozzle to and fro slowly and evenly sever-

al times over the surface, pressing the trigger repeatedly

(illustration E5).

• Then repeat this procedure a few times without pressing the

trigger in order to suck up excess water from the carpet.

Text Coverings with Heavy Soiling

• First switch on only the pump (“PUMP” button).

• Distribute the cleaning agent over an area of approximately

1m².

• Turn the pump off.

• Turn the motor on (“MOTOR” button).

• Move the washing nozzle to and fro slowly and evenly

several times over the surface until the carpet is as dry as

possible.

• Do not walk on the carpet or textile covering while it is still

wet.

• Wait until the covering has completely dried.

Wet Cleaning of Smooth Floors

• Fit the large washing nozzle to the special smooth ﬂ oor

attachment (illustration E6).

• Switch on both the “MOTOR” and “PUMP” buttons (illustrati-

on E1, E2).

• Move the washing nozzle to and fro several times slowly and

evenly over the surface (illustration E7), pressing the trigger

repeatedly.

• Then suck up the moisture without pressing the trigger.

ޥ NOTE:

• The device is ﬁ tted with a temperature safety switch for

the pump.

• If the pump is used frequently it switches itself off by

means of the temperature safety switch. After some time

the pump switches on again automatically.

F – After Use

• Turn the pump off and press the trigger in order to release

the residual pressure (illustration F1, F2).

• Allow the vacuum cleaner to run for a short time without any

load in order to draw the moisture out of the tube and hose.

• Turn the vacuum cleaner off with the “MOTOR” button

(illustration F3).

• Remove the mains plug from the socket (illustration F4).

• Wind the connection lead around the housing (illustration

F5).

• Separate the inlet hose and the suction hose from the

vacuum cleaner (illustration F6, F7).

• Detach the cleaning agent tank (illustration F8).

• Separate the motor housing from the collection container

(illustration F9).

05-BSS 1261 Inhalt 41 13.11.2006, 9:27:09 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic bss 1261 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info