Bedienungsanleitung Clatronic CL 3542 (Seite 33 von 62) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

549706

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Initial operation

Location

• When installing the device, make sure to keep a distance of at

least 50 cm between the unit and any walls or other objects.

• The surface must be at and dry.

Assembly of exhaust pipe

NOTE:

For sliding windows, you may use the window kit provided and

install it in a vertical or horizontal position. Adjust the length of

the seal plate as desired.

1. Turn the adapter (8) to one end of the exhaust pipe.

2. Connect the exhaust pipe to the unit using the exhaust pipe

connector. Turn the pipe anticlockwise several times. Make

sure the pipe is securely connected.

3. Extend the pipe to the desired length.

4. Stick the open end of the pipe into a window.

5. Close the window as far as possible. Also lower any external

roller blinds, if present, to the end of the pipe.

Remote control

1. Open the battery compartment cover on the back of the

remote control.

2. Insert 2 batteries of type R03 “AAA” 1.5 V, observing the cor-

rect polarity (see markings on the bottom of the compartment)!

3. Close the battery compartment cover.

Mains connection

1. Make sure the mains voltage you want to use corresponds to

the voltage of the unit. Please check the rating label for de-

tailed specications.

2. Connect the unit to a properly installed grounded socket. A

signal will sound indicating that the unit is ready for use. The

display will show the current room temperature with low illumi-

nation.

Using the Appliance

Turning unit on/off

• Press the POWER

button to turn on the unit. During ini-

tial operation, the display will show the default setting for

“Cooling” and 22 °C. If operation has been stopped without

disconnecting the plug, all previously set operating mode and

temperature settings will be retained. In that case, the display

will show these settings instead.

• Press the POWER button again to turn off the device. The

display will again show the current room temperature with low

illumination.

Operating modes

Use the MODE

button to select one of the following operating

modes:

• Cooling

• Dehumidifying

• Fan

The display will show the respective icon.

Setting the temperature

Use the UP

or DOWN buttons in “Cooling” mode to set

the temperature. Select a temperature between 16°C and 31°C.

Setting the fan

In “Cooling”

and “Fan” modes you can set the fan speed

with 2 different settings. Press the VENTILATOR button ac-

cordingly.

Setting the air outlet

Adjust the ns to regulate the direction of discharged air.

• Use the lever (1) to adjust the ns to the right / left.

• Turn one of the ns in order to direct the air upwards / down-

wards.

Setting the sleep mode

• When in “Cooling”

mode, use the SLEEP button to

activate the sleep mode.

• After one hour of operation the system will increase the pre-

viously selected temperature by 1°C. After another hour of

operation the system will increase the temperature again by

1°C. There will be no further adjustments after that.

• In sleep mode, the fan operates at the lowest speed setting.

This setting cannot be changed.

• Sleep mode cannot be activated when in “Dehumidifying”

mode.

Dehumidifying

• This operating mode does not support any further settings.

• The fan will operate at the lowest speed setting.

• After approx. 3 minutes of operation the compressor will turn

on and the display will in addition show the

icon.

• The unit will cool the room and extract the humidity from the

air.

Timer (Automatic timer)

Use the timer function to set the power-on and power-off times of

the device. Select a time between 1 and 24 hours.

Using the timer function for automatic power-on

1. Press the POWER

button to turn on the unit.

2. Select the operating mode, temperature and fan speed for the

unit to operate in or at when powered on at the pre-set time.

3. Press the POWER

button to turn off the unit.

4. Press the TIMER button repeatedly to set the hour as

desired. The display will show the icon and the hours after

which the unit will power on automatically.

Using the timer function for automatic power-off

1. Press the POWER

button to turn on the unit.

2. Press the TIMER

button repeatedly during operation to

set the hours as desired. The display will show the icon.

The hours after which the unit will power off automatically, will

briey ash.

NOTE

• In order to deactivate the timer function, use the

button

and select “00”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic CL 3542 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info