Bedienungsanleitung Clatronic CL 3637 (Seite 31 von 50) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

653937

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

CL3637_IM_new 15.12.2015

Using the Appliance

Turning unit on / off

• Press the POWER button to turn on the unit. When used for the ﬁ rst

time, the appliance operates in AUTO mode. If operation has been

stopped without disconnecting the plug, all previously set operating

mode and temperature settings will be retained. In that case, the display

will show these settings instead.

• Press the POWER button again to turn off the device.

Indications on the Display

AUTO

Auto mode

Fan speed

Cooling mode

Indication of the desired room temperature or the

hours in case of TIMER operation

°C

Indication of the temperature setting

Indication with TIMER operation

Dehumidifying mode

The unlit segments do not function on this appliance.

Operating modes

Use the MODE button to select one of the following operating modes:

• AUTO

• Cooling

• Dehumidifying

Operating mode “AUTO” (Automatic)

The appliance decides the must suitable operation mode as shown in the

following table:

Room temperature Operating mode Temperature setting

< 23 °C Fan – – –

≥ 23 °C – < 26 °C Dehumidifying 23 °C

≥ 26 °C Cooling 25 °C

You can set the speed of the fan. The temperature setting cannot be

changed.

Operating mode “Cooling”

In this operation mode, you can adjust the fan speed and the temperature

as desired. If you want to use the appliance with the fan only but without

compressor, set a temperature higher than the actual room temperature.

Operating mode “Dehumidifying”

• This operating mode does not support any further settings.

• The appliance will change the set temperature automatically to room

temperature minus 2 °C.

• The fan will operate at the lowest speed setting.

• The unit will cool the room and extract the humidity from the air.

Setting the temperature

Use the TEMP + or TEMP − buttons in “Cooling”

mode to set the

temperature. Select a temperature between 16 °C and 31 °C.

Setting the fan

In “Cooling”

and AUTO modes you can set the fan speed with 3 differ-

ent settings. Press the SPEED button accordingly.

Timer (Automatic timer)

Use the timer function to set the power-on and power-off times of the

device. Select a time between 1 and 24 hours.

Using the timer function for automatic power-on

1. Press the POWER button to turn on the unit.

2. Select the operating mode, temperature and fan speed for the unit to

operate in or at when powered on at the pre-set time.

3. Press the POWER button to turn off the unit.

4. Press the TIMER button. The display shows the previously set opera-

tion mode and the symbol

. The number of hours ﬂ ashes.

5. You can set the desired number of hours with the buttons TEMP +

and TEMP −. The setting changes rapidly when you hold down the

respective button. Conﬁ rm your setting with the TIMER button while

the display is ﬂ ashing. Otherwise you will exit the setting mode. In this

case, the setting will not be applied.

Using the timer function for automatic power-off

1. Press the POWER button to turn on the unit.

2. Press the TIMER button during operation. The display also shows the

symbol

. The number of hours ﬂ ashes.

3. Set the timer as described in the above item 5.

NOTE:

• Press the TIMER button again if you want to deactivate the TIMER

function.

• You may also cancel the timer function at any time by pressing the

POWER button to turn the unit on / off.

Emptying the water tank

The unit integrates a water tank for collecting condensation. When the

water tank is full, the pilot lamp “WATER FULL” lights up. The display

shows “E2”. The compressor switches off in each operation mode. The

fan keeps running independent of this.

CAUTION:

Do not transport the appliance while the water tank is full. Water could

get into the appliance.

For continued operation with the compressor, you must empty the water

tank. For this, you need a ﬂ oor cloth, a ﬂ at bowl with a capacity for approx.

1,5 litres of water and the water hose supplied with the appliance.

1. Disconnect the mains plug from the wall socket.

2. Place the ﬂ oor towel and the ﬂ at bowl underneath the water outlet. If

possible, set the bowl on a lower level than the appliance.

3. Remove the rubber cap and the plug. Keep the parts for later use.

4. Connect the water hose to the water outlet of the appliance. Place the

end of the hose in the bowl.

5. After the water has been discharged, remove the water hose. Close

the water outlet on the appliance again with the plug and the

rubber cap to ensure the condensation water cooling circulation.

Terminating operation

1. Press the POWER button to turn off the unit.

2. Disconnect the mains plug from the wall socket.

Cleaning

WARNING:

• Always disconnect the mains plug from the wall socket

before cleaning!

• Make sure no water enters the openings of the unit

during cleaning. Otherwise this might result in an

electric shock or ﬁ re.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic CL 3637 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info