Bedienungsanleitung Clatronic CL 3750 (Seite 45 von 78) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

725573

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

CL3750_IM_neu 18.12.2019

Using the Appliance

• Settings made via the appliance are not transmitted to the remote

control.

• As soon as you press a button on the remote control, the appliance will

apply the corresponding settings from the remote control.

• Your selection will appear on the display of the remote control.

• The and buttons must be pressed several times to select the

individual functions.

The buttons on the control panel are explained below. The indicator lights

show your chosen selection.

Operating Modes

Use the MODE button to select one of the following operating modes:

• Cooling COOL

• Dehumidifying DRY

• Fan FAN

Operating Mode “Cooling”

In this operation mode, you can adjust the fan speed and the temperature

as desired.

NOTE:

To operate the appliance with the compressor, the set temperature must

be lower than the current room temperature.

Operating Mode “Fan”

This mode only allows you to set the speed of the fan.

Operating Mode “Dehumidifying”

• This operating mode does not support any further settings.

• The fan speed is preset to the lowest level LOW.

• The appliance will cool the room and extract the humidity from the air.

• When using the mode “Dehumidifying” over an extended period, we

recommend permanently connecting the supplied water hose to the

upper water drain (see gure). Remove the top plug rst. Place the end

of the water hose in a container of sufcient size (e. g. a bucket).

Setting the Fan

In “Cooling” and “Fan” modes you can set the fan speed with 3 different

settings. Press the FAN SPEED button accordingly.

• LOW (low)

• MEDIUM (medium)

• HIGH (high)

Setting the Temperature

• Use the or buttons in “Cooling” mode to set the temperature.

• Select a temperature between 16 °C (61 °F) and 31 °C (88 °F).

NOTE:

Switching between °celsius and °fahrenheit is only possible using the

button on the remote control.

“Sleep Mode”

• Press the SLEEP button when the appliance is switched on and in the

“Cooling” operating mode.

• The fan speed is preset to the lowest level LOW. This cannot be

changed.

• The display will switch off after 10 seconds.

• After running for one hour in the “Sleep” mode, the preset temperature

will automatically increase by 1° C. This will be repeated one hour later

again. This way, a comfortable room temperature will be achieved.

Setting the Air Outlet

Use the button to set the direction of the airow being emitted.

• Press the button multiple times until the pivoting ap is set into the

desired position.

Timer (Automatic Timer)

Use the timer function to set the power-on and power-off times of the

appliance. Select a time between 1 and 24 hours.

Using the Timer Function for Automatic Power-On

1. Press the POWER button to turn on the appliance.

2. Select the operating mode, temperature and fan speed for the appli-

ance to operate in or at when powered on at the pre-set time.

3. Press the POWER button to turn off the appliance.

4. Press the button. The number of hours ashes.

5. You can set the desired number of hours with the buttons and .

The setting mode is automatically exited after approx. 5 seconds. Timer

operation is activated and the TIMER indicator light illuminates.

NOTE:

Do not press the button after setting the hours, as the timer

operation will not be saved.

Using the Timer Function for Automatic Power-Off

1. Press the POWER button to turn on the appliance.

2. Press the button during operation. The number of hours ashes.

3. Set the timer as described in the above item 5.

NOTE:

• If you want to deactivate the set timer operation, press the button

twice. The TIMER indicator light goes off.

• You may also cancel the timer function at any time by pressing the

POWER button to turn the appliance on / off.

MIRAGE Button

Press the MIRAGE button to switch the display located in the front of the

appliance on or off.

Emptying the Water Tank

The appliance integrates a water tank for collecting condensation. When

the water tank is full, the pilot lamp BUCKET FULL lights up. The appli-

ance switches off.

CAUTION:

Do not transport the appliance while the water tank is full. Water could

get into the appliance.

In order to continue operation, you need to empty the water tank. For this,

you need a oor cloth, a at bowl with a capacity for approx. 0.5 litre of

water and the water hose supplied with the appliance.

1. Disconnect the mains plug from the wall socket.

2. Place the oor towel and the at bowl underneath the water outlet. If

possible, set the bowl on a lower level than the appliance.

3. Remove the bottom plug.

4. Connect the water hose to the water outlet of the appliance. Place the

end of the hose in the bowl.

5. After the water has been discharged, remove the water hose. Use the

stopper to close the water drain on the appliance again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic CL 3750 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info