Bedienungsanleitung Clatronic dbs 3278 (Seite 27 von 42) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Norwegisch)

323820

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

ENGLISH

• Then re-tighten the seal. We recommend rinsing out the

water tank approximately 3 times with fresh water.

• Do not ﬁ ll battery water, water from the clothes dryer and

water containing additives (such as starch, perfume,

softener or other chemicals) into the water reservoir. This

could damage the iron due to residues forming in the steam

chamber. These residues may cause impurities to the fabric

when dropping out of the holes in the soleplate.

Connected Wattage

The station has a total maximum wattage of 2000 W. With this

connected load a separate supply line protected by a 16 A

household circuit breaker is recommended.

CAUTION:

Warning - Danger of Overload! Do not use any extension

leads or multiple sockets as this device is too powerful.

Using the Machine

Ironing without steam

1. Sort out the garments according to their ironing tempera-

tures.

2. Always set the temperature control to „MIN“ before connec-

ting the appliance to a power point, or before disconnecting

it.

3. Electrical connection:

• Make sure that the iron voltage (see name plate) and

the line voltage match.

• Only connect the machine to a properly installed safety

socket, 230 V/50 Hz.

4. Start with the lower temperatures. It is set with the thermo-

stat (1):

• Synthetics, silk low temperature

• • Wool medium temperature

• • • Cotton, linen high temperature

MAX maximum temperature

5. Place the iron on its stand.

6. The control lamp on the handle of the iron shows that it

is heating up. As soon as the control lamp goes off the

operating temperature has been reached. Now you can start

ironing. Always turn the temperature control to MIN after use

and remove the mains plug (the control lamp in the handle

goes off).

Steam Ironing

For this a high temperature is needed.

1. Turn the temperature control (1) to position „• • •“ (cotton,

linen).

2. Turn the O/I operating switch (10) on the station to position

I. The control lamp in the switch shows that it is on standby.

When the control lamp (5) lights up there is enough steam

for steam operation.

WARNING:

The steam is hot! There is a danger of scalding!

3. With the steam jet button „

“ you can create a short and

powerful jet of steam.

How can I replenish the water during operation?

If the pressure falls during operation you can ﬁ ll more water into

the tank at the same time.

1. First turn operating switch to O (The lamp in the I/O switch

goes off).

ޥ NOTE:

If there is still some residual pressure in the water tank, a

safety lock prevents the water tank catch (7) from being

opened.

WARNING:

The residual pressure ﬁ rst has to be relieved before

the device can be safely opened.

3. With the steam jet button „

“ you can now release the

residual steam pressure. If no more steam comes out of the

soleplate, please remove the plug and release the water

tank lock (7) carefully.

WARNING:

The steam is hot! There is a danger of scalding!

ޥ NOTE:

If it is not yet possible to open the lock of the water tank

the device needs a further 2 to 3 minutes to cool down.

Then release the residual pressure again.

4. Use the funnel (12) to ﬁ ll pure distilled water from a measu-

ring beaker into the water tank. Do not overﬁ ll! Take care of

water splashes that might come out of the boiler. In order to

prevent the water from splashing it should be ﬁ lled into the

funnel slowly after the safety lock has been opened.

5. Fasten the safety lock again.

6. Insert the power plug back into the socket.

7. Always turn the temperature control to MIN after use, turn

the operating switch (10) to O and remove the mains plug

from the socket (the lamp in the I/O switch goes off).

WARNING:

Never open the water tank lock while the device is being

operated.

When ironing at low temperatures, please ensure that you do

not use any steam.

Vertical Steam

This can be used to produce a jet of steam in a vertical direction.

Self-Cleaning

Due to the large amount of heat produced and the pressure

of the steam, residues that form in the soleplate are removed

automatically.

05-DBS 3278.indd 2705-DBS 3278.indd 27 25.08.2008 11:40:29 Uhr25.08.2008 11:40:29 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic dbs 3278 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info