Bedienungsanleitung Clatronic DKP 3583 (Seite 25 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

653876

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Unpacking the appliance

1. Remove the appliance from its packaging.

2. Remove all packaging materials such as lms, ller mate-

rial, cable clips and carton.

3. To prevent hazards, check the appliance for any transport

damage.

NOTE:

Production residue or dust may have collected on the appli-

ance. We recommend cleaning the appliance according to

chapter “Cleaning”.

Attaching the handles

The handles can be attached to the left and right side respec-

tively.

The handles feature clamps that t into the openings of the

housing.

• Push the clamps into the housing and secure by using the

screws provided.

Electrical Connection

Connected load/wattage

The hob can take up an overall load of 2500 W. Because of

this high connected load it is recommended to use a separate

connection protected over a 16 A safety switch.

CAUTION: Overload!

Do not use extension cables or multiple sockets as the power

consumption of this device is too high for these.

Connection

• Before inserting the mains plug into the socket check

whether the voltage which you intend to use corresponds

to that of the machine. Please see the label on the machine

for details.

• Only connect the machine to a correctly installed safety

socket.

Apply the following description to both hot plates:

Initial Operation of the Unit

Before rst use, operate the unit for 5 minutes to remove the

protective coating of the hotplate. Set the thermostatic control-

ler to MAX.

NOTE:

Occurrence of light smoke and odours is normal with this

procedure. Take care of suitable ventilation.

Using the Hotplate

Switching on/off

The unit is switched on with the thermostatic controller.

The unit is switched off when the thermostatic controller is set

to MIN.

Notes for cooking utensils

• For optimum use of energy, use only pots/pans with a at

bottom (see Fig.).

• The cooking utensil never should be smaller than the hot-

plate. This wastes energy. In extreme cases, the hotplate

can become distorted.

Operation

Use the thermostatic controller to select the temperature of the

hotplate according to the purpose:

Notch 1: Warming up

Notch 2: Warming up/simmering

Notch 3: Simmering

Notch 4: Frying

Notch 5: Parboiling, browning

Notch MAX: Browning, quick heating

NOTE:

The pilot lamp indicates the heating up of the hotplate. It is

switched on and off during operation. This is normal and

indicates that the temperature is controlled and maintained

by the thermostatic controller.

Switching Off

• Set the thermostatic controller to MIN.

• Remove the mains plug from the socket.

• Let the unit cool down before storing it.

WARNING: Hazard of burns!

Because of the heat radiated during cooking, dangerously

high temperatures may occur at the cooking zone after the

cooking cycle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic DKP 3583 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info