Bedienungsanleitung Clatronic DR 3280 (Seite 30 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

534819

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

Unpacking the Device

• Remove the main device and accessories from the box.

• Also remove any packaging materials that may be present.

• Check the scope of delivery.

Initial Operation

Filling up the Heating Boiler before Use!

Before the tank cap is opened it must be ensured that the device

is not under any pressure. Please proceed as follows:

1. Remove the plug from the socket.

2. Turn the lock (22) on the steam pistol (20) to ON (Fig. B1).

3. Press the steam switch (21) on the steam pistol (Fig. B2).

Point the steam nozzle at a surface which is allowed to

become wet.

ޥ NOTE:

After prolonged periods of non-use it is normal for a small

quantity of condensation to come out of the steam pistol

at ﬁ rst.

WARNING:

• If the device is still warm after an interruption to

its use there is a danger of injury!

• Please open the safety lock (6) only when no more

steam comes out of the nozzle.

4. Turn the lock in an anticlockwise direction.

ޥ NOTE:

For your protection the safety lock has a release device.

If the pressure in the kettle is still too high, this release

device prevents it from being opened.

5. Shake any residual water out of the kettle (7). Fill freshwater

from the measuring beaker (15) into the kettle. Take care of

water splashes that might come out of the boiler. In order to

avoid water spray, please use the funnel supplied (Fig. E).

The water should be ﬁ lled in slowly.

CAUTION:

• Do not overﬁ ll! Max. water capacity: 1.5 litres

• Do not use condensation from a tumble dryer (chemi-

cal residues)! This is not distilled water!

6. Retighten the safety lock (6) in a clockwise direction.

Attachment of the Individual Accessories

It is possible to attach the individual nozzles directly to the steam

pistol (20) of the hose (1):

• Attach the jet nozzle (14) to the steam pistol until it locks in

place.

• In order to release the nozzle again, please press the button

on the steam pistol.

• Keep the button pressed down and then pull the nozzle off.

Or extend the nozzle attachments with one or two extension

tubes (8):

• Please insert the sections of the 2-part extension tube one

inside the other until it locks into place (Fig. G). Then attach

it to the steam pistol (20).

• Attach the ﬂ oor brush (18) to the extension tubes: press the

jointed adapter (17) on to the ﬂ oor brush and turn it tightly

through 180°.

• If you would like to use the non-woven cloth, attach it to the

ﬂ oor brush with the help of the clips (Fig. H).

• In order to release the extension tube, please press the but-

ton on the steam pistol.

ޥ NOTE:

Various attachments can only be used in conjunction with the

adapter (13). Place this on the jet nozzle (14) and ﬁ x it in place

by turning through 90°. Please note the bolts in the adapter

and the guiding groove in the jet nozzle. Check that everything

is properly connected!

Nozzle Adapter Use

Floor brush (18) Jointed

adapter

(17)

• for large ﬂ oor surfaces

(Fig. J)

• with non-woven cloth: for

sensitive surfaces (Fig. K)

Round brushes

(11)

Jet nozzle

(14)

with adap-

ter (13)

• for joints, ﬁ ttings, grill grid

etc or

• for difﬁ cult-to-access areas

(Fig. I and L)

High-pressure

nozzle (12)

Jet nozzle

(14)

with adap-

ter (13)

• for concentrated, high

steam pressure (Fig. M)

Window wiper

(19)

Jet nozzle

(14)

with adap-

ter (13)

• for windows or shower

partitions

Jet nozzle (14) Adapter

(13)

• without attachments, e.g. for

car wheel rims (Fig. N)

WARNING: THERE IS A DANGER OF INJURY!

Never attach or remove the accessories if the steam switch

(21) is pressed in! Wait until the device has cooled down.

Electrical Connection

1. Before inserting the plug into the socket. Make sure that the

mains voltage to be used matches that of the device. You

can ﬁ nd this information on the nameplate.

2. Connect the device to a duly installed 230V/50Hz protective

contact socket.

Connected Wattage

The station has a total maximum wattage of 1500 W.

05_DR 3280.indd 3005_DR 3280.indd 30 18.12.2008 9:28:51 Uhr18.12.2008 9:28:51 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic DR 3280 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info