Bedienungsanleitung Clatronic HMS 2739 (Seite 27 von 42) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Norwegisch)

72230

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

ENGLISH

Instructions for Use

Always choose a utensil and a speed according to the following

table:

Product/Type of

Preparation

Max.

Quantity

Utensil Level

Max

Ope-

rating

Time

Heavy dough (e.g.

yeast dough)

500 g

kneader

hook

1 - 4 3 min.

Cake mixture, Dres-

sings, Desserts

750 g beater 2 - 5 5 min.

Sponge mixture, wafer

mixture, Cream

750 g beater 2 – 5 5 min.

Liquids, shakes up to 1 l blender 5 or turbo 1 min.

• With heavy mixtures, do not operate the machine for more

than 3 minutes, and then allow it to cool down for a further

10 minutes.

• Depending on the consistency of the mixture it is necessary

to remove the mixture from the edge of the mixing bowl and

place it back on the kneading attachments. The device must

be turned off.

Releasing the kneading hook / beater

1. In order to release the kneading hook/whisk (10) turn the

power level selector switch to „0“ and ensure that the mixer

has been disconnected from the mains.

2. Press the button (2) to release the kneading hook/whisk.

Remove the device by turning it slightly.

ޥ NOTE:

The hooks can only be removed if the speed switch (3) is in

the „0“ position.

Turbo operation

This is for switching to maximum speed for a short time. Press

at short intervals for pulsed mode operation.

CAUTION:

Do not use this function for more than one minute!

How to use the Blender

1. Turn the power level selector switch (3) to „0“ and ensure

that the mixer (1) has been disconnected from the mains.

2. On the back of the mixer push the cover of the installation

aperture upwards.

3. Place the fast mixing rod on the installation aperture in such

a way that the two arrows are pointing one above the other.

To lock the rod in place, turn it through approximately 90° in

a clockwise direction.

4. Insert the mains plug into a properly installed 230 V/50 Hz

safety power socket.

5. Place the fast mixing rod into a high-walled, partly-ﬁ lled

vessel.

CAUTION:

Do not operate the fast mixing rod when the vessel is

empty, i.e. when there is no food in the vessel to be mixed.

6. Select a speed using the power level selector switch (3).

Move the fast mixing rod slightly up and down.

7. When you would like to stop mixing, turn the power level

selector switch to „0“ and unplug the device from the mains.

How to use the Kneader hooks/beater

1. Turn the power level selector switch (3) to „0“ and ensure

that the mixer (1) has been disconnected from the mains.

2. Press the end of the kneader hooks/beater (10) into the cor-

responding mixer openings until the hooks click into place.

While pressing, turn slightly in order to facilitate the whole

operation.

ޥ NOTE:

Please note that the kneading hook with the curved was-

her on the shaft can only be inserted on the left-hand side

of the mixer when viewed from the bottom.

3. Insert the mains plug into a properly installed 230V/50 Hz

safety power socket.

4. The handmixer (1) can be used at various speeds set with

the speed regulator (3).

How to use the Mixer stand

Please select a ﬂ at non-slip surface for the mixer stand.

1. Place the hand mixer (1) on the upper section (5) of the

mixer stand (11). Please check whether the clip (12) of the

upper section is locked in place on the back of the mixer.

2. Mount the hooks as described above in the section “How to

use the Kneader hooks/beater”.

3. In order to place the mixing bowl (8) underneath, pull the clip

(6) to unlock the upper section of the mixer stand (5) and

fold the mixer upwards.

4. Place the mixer bowl ﬁ lled with the desired ingredients onto

the revolving plate (7). Now fold the mixer down again.

5. Insert the mains plug into a properly installed 230V/50 Hz

safety power socket.

6. The handmixer (1) can be used at various speeds set with

the speed regulator (3).

7. The revolving plate turns automatically!

8. When you would like to stop mixing, turn the power level

selector switch to „0“ and unplug the device from the mains.

9. When you have ﬁ nished pull the clip (6) again to unlock

the upper section of the mixer stand (5) and fold the mixer

upwards.

10. Now the mixer bowl can be removed. Remove the hooks

as described above in the section “Releasing the kneading

hook / beater”.

11. In order to separate the mixer from the upper section (5) of

the mixer stand, pull the mixer upwards.

Cleaning

• Before cleaning the equipment, always remove the mains

plug from the socket.

• Only a damp cloth should be used for cleaning the outside

of the machine.

• Under no circumstances should the device be immersed in

water for cleaning.

05-HMS 2739 New.indd 2705-HMS 2739 New.indd 27 04.06.2008 10:05:11 Uhr04.06.2008 10:05:11 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic HMS 2739 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info