Bedienungsanleitung Clatronic NM 3795 (Seite 13 von 74) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

814293

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

NM3795_IM 19.04.23

Selection of Needle Size and Threads

Needle system: System 130 at-shank needle

Needle

Size Fabrics Thread

(12)

Medium weight

fabrics: Cotton, satin,

workwear, canvas,

double-faced fabrics,

lightweight wool

Most threads are of

medium size and

suitable for these

fabrics and needle

sizes.

For best results:

use polyester

threads for syn-

thetics and cotton

or naturally woven

fabrics. Always use

the same thread at

the top and bottom.

(14)

Medium weight

fabrics: Wool, heavier

knitwear, terry cloth,

denim fabrics

100

(16)

Heavy fabrics: Wool,

tent fabrics and quilted

fabrics, denim, uphol-

stery fabrics (light to

medium)

110

(18)

Heavy fabrics: Wool,

coat fabrics, upholstery

fabrics, some leather

and vinyl (with leather

needles)

Durable thread

Operation

Inserting the Needle

WARNING: Risk of Injury!

Before inserting or replacing the needle, unplug the

power supply unit from the sewing machine.

Change the needle regularly, especially if it is bent or the

tip is damaged. A bent needle causes skipped stitches.

Defective needle tips damage the fabric.

Insert the needle as follows:

1. The needle guide must be com-

pletely raised. Turn the handwheel

(6) in the direction of the arrow.

2. Loosen the needle clamp screw

(21) and remove the old needle.

3. Insert the new needle as far as it

will go. The at side of the needle

must face backwards.

4. Tighten the needle clamp screw again.

Attaching and Removing the Presser Foot

There are different types of presser feet. You can buy them

in shops. Make sure you get the right size. Not all presser

feet t every sewing machine.

To change or remove the presser foot, refer to the following

description with the illustrations 1 – 3.

1. Illustration 1:

Pull the presser foot lever (17) up. Loosen the presser foot

xing screw (a). Place the presser foot holder (b) on the

presser foot bar (c) and tighten the screw (a).

2. Illustration

Place the presser foot (d) on the needle plate. Lower the

presser foot lever (17) until the notch (e) is exactly over

the presser foot pin (f). Press the lever (g) until the pin (f)

engages in the notch (e).

3. Illustration

To remove the presser foot (20), press lever (g). The

presser foot falls off.

Threading the Upper-thread

For threading the upper-thread, refer to the illustrations

below. Also refer to the illustrated instructions on the

appliance.

When threading, make sure that the presser foot (20) is

raised and the thread lever (1) is in the uppermost position!

1. Place the thread spool on the

thread spool holder (15).

2. Pull the thread through the thread

guide (16).

3. Guide the thread down past the

adjusting wheel (2).

4. When you reach the bottom, guide

it up the left side to the thread

lever (1).

5. Guide the thread through the hole

on the thread lever (1). Make sure

that the thread is inserted from

right to left.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clatronic NM 3795 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info