703394
19
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
19 EN
The lter should be replaced every 12 18 months; the UV-C lamp (12)
should be replaced every 12 – 24 months. If you have any questions about
spare parts, please contact the customer service department via our web-
site: www.dspro.de/kundenservice
Use
PLEASE NOTE!
The device should only be used if it has been completely and correctly assembled!
The dust container and the lter must be inserted and must not be damaged. If
the dirt were to get inside the motor unit, this could damage the motor.
Make sure that the safety switches of the UV-C lamp are not blocked!
Switch the device off after each surface has been cleaned as this will considerably
increase the operating time on each battery charge. Charge up the battery after use
(see the “Charging Up the Battery” chapter).
1. Place the device down fl at on the surface which is to be cleaned.
2. Press the On / Off switch (2) to switch on the device. The device starts to vacuum and
the UV-C lamp (12) and the vibration head (11) switches on.
The vibration shakes up the surface which is to be cleaned and the dust which
is agitated is sucked in through the suction opening (8).
3. Guide the device very slowly and evenly over the surface to be cleaned.
4. After vacuuming, press the On / Off switch to switch off the device.
Cleaning and Storage
PLEASE NOTE!
Empty the dust container each time after you use the device. The lter must also be
regularly cleaned in order to prevent overloading of the motor.
Do not use any sharp or abrasive cleaning agents or cleaning pads to clean the de-
vice. These can damage the surface.
As required, wipe down the motor unit (4) with a damp soft cloth. Then dry it with a
soft cloth.
Wipe out the recess for the dust container (5) with a duster.
Store the device in a dry, cool place that is not accessible to children and animals.
Cleaning the Dust Container and HEPA Filter
1. Press onto the dust container (5) to unlock it.
2. Reach into the recess in the dust container and pull it up and out of the motor unit (3).
3. Reach into the opening and pull the HEPA-fi lter out of the dust container.
4. Empty the dust container.
5. Wipe out the dust container with a dry duster if necessary.
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Cleanmaxx SV1801 - Z03416 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info