Bedienungsanleitung Clifford Concept 50 (Seite 16 von 23) (Englisch)

468917

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Remote controlled sensor testing and adjustment

Because of ever-changing conditions, all alarms require periodic fine-tuning of the sensors.

In fact, an improperly adjusted sensor is, by far, the biggest cause of false alarms. With

other alarm brands, this requires repeated trips back to the dealer. Not so with Concept

50. You can adjust sensitivity without any tools and without even knowing where the

sensor is mounted! All you need is your car alarm’s remote control. If at any time you

find the setting(s) of your system’s sensors to be either too sensitive (i.e., it tends to false

alarm) or not quite sensitive enough, you may individually test and adjust the sensitivity

settings yourself. To adjust the Glass Tampering Sensor or either zone of the Dual-Zone

Magnetic Resonance Sensor, just use the following procedure:

1. Insert your car key and turn the ignition switch to its “ON” position, but do not start

the engine.

2. Enter your disarming code, then press and hold the switch to its spring-loaded

momentary side for about 3 seconds until you hear a siren chirp. You’ll also notice

that the system’s LED is on to indicate that the system is in its programming mode.

4. Toggle the switch in and out of the latched position 3 times (i.e., latched, center,

latched, center, latched, center). You will hear a chirp for each latched-center you

perform.

5. To select either the sensor and/or zone, perform either a, b or c of this section:

a. To test/adjust the primary (normal) sensing zone of the Magnetic Resonance

Sensor, tap and release the momentary side of the switch one time.

b. To test/adjust the secondary (high) sensing zone of the Magnetic Resonance

Sensor, tap and release the momentary side of the switch two times.

c. To test/adjust the Glass Tampering Sensor, tap and release the momentary side of

the switch three times.

6. Turn the ignition off, exit the vehicle and close the doors.

7. To test the current sensitivity setting:

a. Magnetic Resonance Sensor: “Thump” the window pillar with the side of your

fist. (For the primary zone, thump somewhat firmly, but not nearly so hard as to

dent the window pillar. For the secondary high-sensitivity zone, thump rather

lightly). If the sensor registered the thump, you will hear a single siren chirp.

b. Glass Tampering Sensor: Firmly tap on the window with a coin (the larger the

better). If the sensor registered the tap, you will hear a single chirp.

8. To increase sensitivity, press button 2 on your remote control. To decrease it, press

button 4. To confirm the change of setting, each time you increase sensitivity, the

siren will chirp in higher and higher pitched tones. Conversely, as you decrease

sensitivity, the chirps will have lower and lower pitched tones. Release the button

when you hear the chirp. Press and release the appropriate button until the desired

sensitivity is reached. There are 16 sensitivity steps for each sensor zone. If you

reach the highest or lowest setting, the system will confirm this with two chirps of

the siren.

9. Press remote control button 1 when done to exit programming mode (you’ll hear a

chirp and the LED inside the vehicle will turn off to indicate that the system has

exited programming mode). You may now either enter the vehicle to drive it or

program another feature, or press button 1 to arm the system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Clifford Concept 50 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info