Bedienungsanleitung Cloer 4959 (Seite 8 von 20) (Deutsch, Englisch, Holländisch, Französisch)

565540

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

vered with water, otherwise the appliance can

not switch o properly.

ATTENTION: Make sure not to ll water past the

MAX marking (= 1,7 l) on the water level display.

Scalding may result from water boiling over.

Close the lid manually and place the electric

kettle anywhere on the 360° contact base.

Your water boiler is equipped with a tempera-

ture control and works by touch (please see also

“Touch control panel“).

Select the desired temperature (between 40°

and 100°C) by touching it on the “Touch-Tempe-

rature Strip“. The LED display then lights up blue

to this point.

INFO: Water will boil at a temperature of 100°C.

Please observe that the water temperature after

boiling may deviate from the selected tempera-

ture by a few degrees Celsius.

To switch it on, press the ON/OFF switch on the

touch panel.

When the water reaches the desired tempera-

ture, the electric kettle will beep three times and

then switches o automatically.

The LEDs of the temperature control will light

up afterwards.

You can interrupt the boiling process at any time

by pushing up the ON/OFF switch again.

Please wait a moment until the water stops

bubbling.

To pour the water, lift the electric kettle from the

contact base.

IMPORTANT: Always make sure that the device

is switched o before removing the electric

kettle from the contact base.

Wait a few minutes to let the device cool off be-

fore filling it with water again and using it. Do

not touch the hot housing during operation.

Danger of burning!

Keeping warm function

You can keep the water hot after boiling.

Proceed as described in „Operation“, but push

the button for keeping warm instead of the ON/

OFF switch.

This automatically operates the ON/OFF switch

and the device starts to boil.

Then the water is kept warm on the selected

temperature.

You can remove the water boiler from the

contact socket at any time during the keeping

warm time, pour water and return it, which will

continue the keeping warm function.

You can stop the keeping warm function at

any time by pushing the keeping warm button

again.

Otherwise, the device will automatically switch

off after approx. 2 hours.

You may also switch on the keeping warm

button subsequently during a regular boiling

process.

For this, boil water as usual and select the

keeping warm button after pushing the ON/OFF

switch.

Dear Customer

We wish you much pleasure with your new

electric kettle with touch panel.

Your Cloer Company

Preparation for use

Remove all packaging elements and labels, but

not the rating plate.

Place the electric kettle on a dry, even, non-slip

surface.

Before initial use

Please read these operating instructions care-

fully before using the device for the rst time

and save these instructions in case you want to

read it again.

Boil at least once 1.7 l water at 100°C, and then

pour this away.

Safety notices for use of the

contact base / electric kettle

Do not come below the MIN marking (= 0.8 l) on

the water level display, otherwise the appliance

can not switch o properly.

Do not ll the electric kettle with water past the

MAX marking (= 1,7 l) on the water level display.

Scalding may result from water boiling over.

Always remove the electric kettle from the

contact base before lling with water.

This electric kettle may only be used for heating

water.

Do not place this appliance on or near a hot gas

or electric burner.

Before operating the machine, make sure that

the contact base is dry.

Please make sure that water is never spilled on

the contact base.

If water is accidentally spilled onto the contact

base, proceed as follows:

– Unplug the unit from the wall socket.

– Dry the contact base with an absorbent

dry kitchen towel.

– Dry the surface beneath the contact base.

– Plug the unit into the wall socket again.

Never leave the appliance unattended when in

use.

CAUTION!

The surface is hot during

operation. Only touch the

device at its handle.

Touch control panel

Your electric kettle is equipped with a tem-

perature control and a “keep-warm“ function,

controlled by a modern touch control panel. For

both a temperature in the range of 40° -100°C

can be selected. The closed surface prevents

dirt, dust or water to get into the base interior.

Operation

Plug the power plug into the wall socket.

Remove the electric kettle from the contact

base.

Open the lid by pressing the cover release knob

at the handle.

Fill the electric kettle with desired amount of

cold tap water using the water markings on the

water level display behind the handle.

ATTENTION: Make sure not to ll below the MIN

marking (= 0.8 l) so that the heat detector is co-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cloer 4959 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info