Bedienungsanleitung Cme Control TV 100 (Seite 4 von 16) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

497771

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Find them on your

CONTROL TV 100

remote control by pressing the keys one by one and discovering the commands that interest you.

PROBLEM SOLVING

SOLUTION

Try some of the other frequently-used keys. If the problem persists,

check that the batteries are fitted correctly. If necessary, replace them

with 2 new 1.5 V AAA/LR03 batteries.

Check that the batteries are new and that the remote control is pointing

at the TV without any obstacles in the way. If required, reset the remote

control code, following the programming procedure.

The batteries are low. Change them.

You may have used the wrong code.

Reset the remote control code, following the programming procedure.

To find the code with which to program your remote control consult

the on-line guide at www.cme.it

PROBLEM

The TV does not respond and the light indicator does not light up

when a key is pressed.

The TV does not respond but the light indicator does light up.

The light indicator flashes when a key is held down but the TV

does not respond.

The remote control commands are not all working correctly.

The make of your TV is not included in the list of codes at the end

of this booklet.

CURRENT CODE DISPLAY

To find out the code of your remote control, follow this procedure:

1. Hold down the and keys together for 5 seconds until the light indicator starts to flash.

2. When you release the and keys, within 8 seconds press and release the key.

3. After a few seconds, the light indicator communicates the code you are looking for by flashing the four numbers separately. Count

the number of flashes; each series of flashes corresponds to one figure in the code. 10 flashes correspond to 0.

4. Make a note of the code on the adhesive label inside the battery cover for quick and easy future reprogramming.

N.B. this operation cannot be interrupted and the remote control cannot therefore be used

until the end of the 4 series of flashes.

GLOBAL SEARCH REMOTE CONTROL PROGRAMMING

To display and make a note of the code memorized by means of the search, follow the instructions described in the paragraph

CURRENT CODE DISPLAY.

1. Switch on the TV.

2. Hold down the and keys together for 5 seconds until the light indicator starts to flash indicating that the remote control

is being programmed.

3. Release the keys and enter the code 0000 within 12 seconds. The light indicator flashes more quickly to indicate that the remote

control is ready for the search.

4. Point the remote control towards the TV. Press and slowly release the key several times, stopping when the TV goes off.

5. When the TV goes off, press the key to confirm. Three flashes indicate that the operation has been completed correctly.

CHECK: check that some of the other functions used on your original remote control are working correctly. If the commands function

incorrectly or erratically, you have probably entered a code for a similar remote control but not the right one. In this case,

repeat the search procedure starting from point 2.

N.B. THE LIGHT INDICATOR STOPS FLASHING. The remote control exits programming mode and the light

indicator stops flashing:

• if no keys are pressed for 14 seconds

• if the end of the code search list has been reached. In this case visit the website www.cme.it

If you know the exact code with which to program the remote control, enter it as follows:

ENTERING THE CODE

1. Hold down the and keys together for 5 seconds until the light indicator starts to flash.

2. Release the keys and enter the code (e.g: TV 1100). Three flashes indicate that the operation has been completed correctly.

HOW TO USE THE ADDITIONAL COMMANDS WHICH DO NOT APPEAR ON THE KEYPAD

Although not indicated on the keypad, some keys can be used for additional commands.

For the functions used less frequently, look for the additional commands on the site www.cme.it. As well as easily finding the code

to program your remote control, consult the on-line guide to help you find which keys on the

CONTROL TV 100

remote control

correspond to the additional commands.

This operation can take up to 20 minutes and should be carried out if you have not succeeded in programming the remote control by means

of the method described above.

The quickest and easiest way to program the remote control is by consulting the website www.cme.it.

If you have further questions concerning the CONTROL TV 100 remote control unit, visit www.cme.it to find all the information you need

quickly and easily.

2 year WARRANTY - The warranty is declared null and void if the product is tampered with or used improperly

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cme Control TV 100 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info