Bedienungsanleitung Cme Toptel 2 -200 (Seite 11 von 40) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

497765

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

CURRENT CODE DISPLAY

1. Press the selection button for which you want to know the

code and hold down for 5 seconds.

2. When the button is released it will start to ﬂ ash; press and

release the 1-/-- button within 8 seconds.

3. After a pause of a few seconds, the indicator light

produces four series of ﬂ ashes with a space between them,

corresponding to the code you are looking for. Count the

number of ﬂ ashes; each series of ﬂ ashes corresponds to one

ﬁ gure in the code. 10 ﬂ ashes correspond to 0.

4. Write this code on the adhesive label on the inside of the

battery cover for quick and easy future reprogramming.

To ﬁ nd out the code of your remote control, follow this procedure:

5 SEC.

Code obtained = 1306

NOTE: this operation cannot be interrupted and the remote control

therefore cannot be used until the end of the four series of ﬂ ashes.

ENTERING THE CODE

If, by consulting the on-line guide, you have found the exact code of the appliance with which to programme the

remote control, enter it as follows:

1. Press and hold for 5 seconds the selection button for the

appliance for which you want to enter the code.

2. When the button is released it will start to ﬂ ash; enter the

code (e.g. TV 1306). Three ﬂ ashes indicate that the

operation has been completed correctly.

HOW TO USE THE ADDITIONAL COMMANDS WHICH DO NOT APPEAR ON THE KEYPAD

Although not indicated on the keypad,

some buttons can be used for additional commands.

Search for them on your remote control by pressing the buttons one after the other to ﬁ nd any other commands that

might be of interest to you.

In particular, the additional functions most frequently used, such as NORMALIZATION, COLOUR and BRIGHTNESS,

can be found on the following buttons

Normalization:

For the functions used less frequently, look for the additional commands on the site www.cme.it. Consult the

on-line guide not only to easily ﬁ nd the code needed to programme your remote control, but also to help you ﬁ nd

which buttons on the remote control correspond to the additional commands.

Brightness (+):

Brightness (–):

Colour (+):

Colour (–):

ALWAYS ACTIVE TV FUNCTIONS

The following TV functions are available on the 4 central buttons of the remote control: ON/OFF, VOL-, VOL+ and AV.

These functions can be used to control appliances other than the TV. This makes controlling the digital terrestrial

decoder combined with a TV easier since you no longer need to change the remote control in order to use the audio

functions.

WARNINGS: in rare cases, instead of pressing the TV ON/OFF button to turn ON the TV, you may need to select the TV

button in the upper left and then press any one of the number buttons.

or or

5 SEC.

or or

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cme Toptel 2 -200 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info