Bedienungsanleitung Cobra 150 GTL DX (Seite 13 von 17) (Englisch)

633035

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Alternate Microphones and Installation

•

Nothing comes close to a Cobra

Alternate Microphones

and Installation

English

Alternate Microphones

and Installation

Alternate Microphones and Installation

•

To wire the microphone cable to the plug provided, proceed as follows:

Remove the retaining screw.

2. Unscrew the housing from the pin receptacle body.

3. Loosen the two cable clamp retainer screws.

4. Feed the microphone cable through the housing, knurled ring and

washer as shown Fig. 3B.

5. The wires must now be soldered to the pins as indicated in the wiring table.

If a vise or clamping tool is available, it should be used to hold the pin receptacle

body during the soldering operation so that both hands are free to perform the

soldering. If a vise or clamping tool is not available, the pin receptacle body can

be held in a stationary position by inserting it into the microphone jack on the

front panel. The numbers of the pins of the microphone plug are shown in Fig. 4,

as viewed from the back of the plug. Before soldering the wires to the pins,

pre-tin the wire receptacle of each pin of the plug.

Be sure that the housing and the knurled ring of Fig. 3 are pushed back onto the

microphone cable before starting to solder. If the washer is not captive to the pin

receptacle body, make sure that it is placed on the threaded portion of the pin

receptacle body before soldering.

If the microphone jack is used to hold the pin receptacle during soldering operation,

best results are obtained when the connections to pins 1 and 3 are made first and

then the connections to pins 2 and 4. Use a minimum amount of solder and be

careful to prevent excessive solder accumulation on pins, which could cause a

short between the pin and the microphone plug housing.

6. When all soldering connections to the pins of the microphone are complete, push the

knurled ring and the housing forward and screw the housing onto the threaded portion

of the pin receptacle body. Note the location of the screw clearance hole in the plug

housing with respect to the threaded hole in the pin receptacle body. When the housing

is completely threaded into the pin receptacle body, a final fraction of a turn either

clockwise or counterclockwise may be required to align the screw hole with the

threaded hole in the pin receptacle body. When these are aligned, the retaining

screw is then screwed into place to secure the housing to the pin receptacle body.

7. The two cable clamp retainer screws should now be tightened to secure the

housing to the microphone cord. If the cutting directions have been carefully followed,

the cable clamp should secure to the insulation jacket of the microphone cable.

8. Upon completion of the microphone plug wiring, connect and secure the

microphone plug in the transceiver.

Fig. 2 Microphone cable preparation

Fig. 3 Microphone plug wiring

Your Mobile Radio Your Mobile Radio

Fig. 4 Microphone plug pin numbers viewed from rear of pin receptacle

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cobra 150 GTL DX Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info