Bedienungsanleitung Cobra CPI 1000 (Seite 8 von 15) (Englisch)

538262

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

CAUTION We recommend a main fuse in the

battery’s positive cable to protect against DC

wiring short circuits (external to the inverter).

The fuse should be as close to the battery as

possible. We recommend a Buss Fuse ANL-250

or equivalent. The specific fuse ampere rating

should be sized to allow operation of all your

DC powered equipment.

CAUTION Remove any jewelry (watch, ring, etc.).

Be careful not to short circuit the battery with any

metallic object (wrench, etc.).

WARNING If you are making a permanent AC

connection to the inverter, make sure that the AC

wiring steps are performed before any DC wiring is

done. (DC hook-up energizes internal components,

regardless of the position of the On/Off Switch).

Working on AC connections in such a circumstance

may result in an electric shock.

WARNING 115 volt AC power is potentially lethal.

Do not work on AC wiring when it is connected to

the inverter (even if it is switched off) unless the

DC power source is physically disconnected from

the inverter. Also, do not work on AC wiring if it

is connected to another AC power source such

as a generator or the utility line.

WARNING You may observe a spark when

making the connection because current can

flow to charge the capacitors in the inverter.

Do not make this connection in the presence

of flammable fumes. Explosion or fire may

result. Thoroughly ventilate the battery

compartment before making this connection.

b. Connect the cable from the Positive (Red) Terminal

of the inverter to the Positive Terminal of the power

source (the battery’s main fuse or the battery selector

switch, if you are using one). Make a secure connection.

You might observe a spark when you make this connection

since current can flow to charge capacitors in the inverter.

All power connections to your Cobra inverter must

be Positive to Positive and Negative to Negative.

CAUTION Electrical installations must meet

local and national wiring codes, and should be

performed by a qualified electrician.

CAUTION Do not connect the inverter and another

AC source (such as a generator or utility power)

to the AC wiring at the same time. The inverter

will be damaged if its output is connected to AC

voltage from another source. Damage can even

occur if the inverter is switched off.

CAUTION Do not connect the inverter to an AC

branch circuit that has high-power consumption

loads. It will not operate electric heaters, air

conditioners, stoves, and other electrical

appliances that consume more than 1000 watts.

CAUTION Loose connectors result in excessive

voltage drop and may cause over heated wires

and melted insulation.

CAUTION Reverse polarity connections (positive

to negative) will blow internal fuses in the inverter

and may permanently damage the unit. Such damage

is not covered by the warranty.

NothingComes Close to a Cobra

™

ConnectCables

ConnectingCables ConnectingCables

Installation

10274_CPI1000_vD:CPI1550-Eng 6/27/11 12:08 PM Page 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cobra CPI 1000 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info