Bedienungsanleitung Cobra CPI 880 (Seite 4 von 11) (Englisch)

538266

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Important Safety Information

Introduction

WARNING Power inverters contain components

that can produce arcs or sparks. To prevent fire

or explosion, do not install the inverter in areas or

compartments containing batteries or flammable

materials or in locations that require ignition-

protected equipment.

WARNING To reduce the risk of fire, do not cover

or obstruct the ventilation openings. Do not install

inverter in zero-clearance compartment.

Warning: Wash Hands After Handling Power Cord

The power cord on this product contains lead, a chemical

known in the state of California to cause birth defects or

other reproductive harm.

Caution: Rechargeable Appliances

Certain chargers for small nickel cadmium batteries can be

damaged if connected to the Cobra 800 watt inverter. Two

particular types of equipment are prone to this problem:

1. Small battery-operated

appliances such as flashlights,

razors, and night lights that

can be plugged directly into

an AC receptacle to recharge.

2. Certain battery chargers for

battery packs used in hand

power tools. These chargers

have a WARNING label stating

that dangerous voltages are

present at the battery terminals.

This problem does not occur with the vast majority of

battery operated equipment. Most use a separate charger

or transformer that is plugged into the AC receptacle and

produces a low voltage output. If the label on the AC

adapter or charger states that it produces a low voltage

AC or DC output (less than 30 volts), the inverter will

have no problem powering the adapter safely.

Cobra 800 Watt Output Waveform

Some very sensitive electronic equipment may not operate

satisfactory on “square wave” or “modified sine wave.”

The output waveform is referred to as “square wave” or

“modified sine wave.” It is a stepped waveform designed

to have characteristics similar to the sine wave shape of

utility power. A waveform of this nature is suitable for most

AC loads (including linear and switching power suppliers

used in electronic equipment, transformers and motors).

Quick Evaluation Before Installation

•

This section provides you with basic information about the

inverter and how to check its performance before installation.

Be Sure to Have on Hand:

 A 12 volt DC power source (such as a vehicle battery).

The power source must provide

between 11 and 15 volts DC and

be able to supply enough current to

run the test load. As a rough guide,

divide the wattage of the test load by

10 to get the current (in amperes)

the power source must deliver.

 The provided two foot direct-to-battery 12 gauge cable.

Only use the cable provided with

your inverter.

 A test load that can be plugged into the AC receptacle on

the inverter for short term testing at a low power level.

Quick Evaluation

Before Installation

Introduction

Nothing Comes Close to a Cobra

Plug In Directly

Dangerous Voltages

Power Supply

Cable

Test Load

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cobra CPI 880 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info