Bedienungsanleitung Cobra CS40E (Seite 21 von 32) (Englisch)

634435

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

3.2.2 Stopping the chainsaw

3.2.3 Tips for cutting

Always wear a hard-hat with visor to protect your head from falling branches. The chain

saw can only be used to fell trees smaller in diameter than the length of the guide bar.

- Secure work area. ensure no persons or animals are in the vicinity of the falling tree.

Never attempt to free a jammed saw with the motor running. Use tree wedges to free

chain and guide bar.

a. The tree felling

When cutting and felling operations are being performed by two or more persons, at the

same time, the felling operations should be separated from the cutting operation by a

distance of at least twice the height of the tree being felled. Trees should not be felled in

a manner that would endanger any person, strike any utility line or cause any property

damage. If the tree does make contact with any utility line, the company should be

notifed immediately.

The chain saw operator should keep on the uphill side of the terrain as the tree is

likely to roll or slide downhill after it is felled.

- An escape path should be planned and cleared as necessary before cuts are started.

The escape path should extend back and ideally diagonally to the rear of the expected

line of fall.

- Before felling is started, consider the natural lean of the tree, the location of larger

branches and the wind direction to judge which way the tree will fall. Remove dirt,

stones, loose bark, nails staples, and wire from the tree.

- Notching undercut: Make the notch (x-w)1/3 the diameter of the tree, perpendicular to

the direction of falls as make the lower horizontal notching cut first. This will help to

avoid

• Release the Trigger On / Off to stop the machine.

• The chain stops completely after a few seconds.

• Disconnect the plug source for safety.

• Replace the front hand guard/chain brake level in place.

•

Use only for sawing wood (tree trunks, branches, planks and beams). Never use the

saw for cutting other materials.

•

Take care that the chain does not come into contact with the ground or foreign materials

other than wood.

•

When sawing, do not put pressure on the chain, but allow the chain to bite through the

wood while applying leverage on the area near the bar spikes.

•

When cutting thick branches or trunks, reposition the bar spikes at a lower point to

avoid strain and kickback during operation. To do this, pull the saw toward you

slightly to loosen the clutches of the bar spikes and reposition lower in the material. It

is not necessary to completely remove all of the chainsaw bar from the wood.

•

The best results are obtained when the cutting speed of the chain is maintained

at its top speed.

•

Attention should be paid when coming to the end of the cutting stroke, sometimes

the weight changes unexpectedly. There is a risk of an accident to your legs and feet.

•

Do not remove the chainsaw from the wood when the chain is rotating.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cobra CS40E Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info