Bedienungsanleitung Cobra MR F55-D (Seite 21 von 40) (Englisch)

538285

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Advanced Operation

Scan

During Scan, the radio will rapidly switch from channel

to channel through all the channels. Whenever any activity

is detected, the radio will stop the scan for ten (10) seconds

to allow you to listen briefly on that channel. It will then

continue to scan unless you switch out of the Scan mode.

NOTE

The radio must be squelched for Scan mode to

function. See page 36 for squelch procedure.

To Enter Scan:

From Standby mode, press the Scan button.

The radio will immediately begin to scan the entire channel

map selected in the active channel map.

SCAN will show

on the LCD.

To Exit Scan:

From Scan mode, press the Scan button.

This will return the radio to Standby mode on the last

scanned channel.

During Scan (while receiving an incoming transmission),

You Can Choose From The Following:

■

Press the Talk button to remain on that channel and end

scanning. This will return the radio to Standby mode.

■

Press the Up/Down buttons to resume scanning.

If you do not press any buttons within ten (10) seconds,

your radio will automatically resume scanning.

During Scan (while not receiving a transmission):

Press the Talk button to communicate on the last

channel scanned and return to Standby mode.

Operating Your Radio

Scan Button

Scan

Scanning

Nothing Comes Close to a Cobra

English

Advanced Operation

Dual-Watch

Dual-Watch gives you one (1) button access to scan the two (2) locations of most

importance to you. Channel 16 will always be included as a scanned location. The

remaining location will be the VHF channel in effect when you enter Dual-Watch mode.

NOTE

The radio must be squelched for dual-watch to function. See page 36

for squelch procedure.

To Enter Dual-Watch Mode:

1. In Standby mode, use the Up/Down buttons to go

to the channel you want to add as the second location

to be scanned.

2. Press the Dual-Watch button.

Dual-watch will be indicated on the LCD and the radio

will scan between Channel 16 and the second dual-watch

location you selected. A signal on any one (1) of the two (2)

channels will stop the scan to allow you to listen to the traffic

on the channel. The channel number will be displayed on

the LCD.

To Exit Dual-Watch Mode:

Press the Dual-Watch button. The radio will

return to Standby mode.

During Dual-Watch (while receiving an incoming

transmission), You Can Choose From The Following:

■

Press the Talk button to remain on that

dual-watch location and return to Standby mode.

■

Press the Up/Down buttons to resume scanning

dual-watch locations.

If you do not press any buttons, your radio will

automatically resume scanning dual-watch locations

when the incoming transmission is complete.

During Dual-Watch (while not receiving a transmission):

Press the Talk button to communicate on the last

dual-watch location scanned and return to Standby mode.

Operating Your Radio

Dual-Watch Button

Standby Mode

Dual-Watch Mode

F55D_Operation_Eng:8186-F55_Operation-Eng 12/8/10 8:25 AM Page 46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cobra MR F55-D Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info