Bedienungsanleitung Cobra MR HH125 (Seite 15 von 30) (Englisch)

521975

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

VHF Marine Radio ProtocolsOperating Your Radio VHF Marine Radio ProtocolsOperating Your Radio

Nothing Comes Close to a Cobra

Advanced Operation

English

Advanced Operation

To Recall a Stored Memory Location:

1. Press the Memory/Escape button. The MEM icon will be

turned On.

2. Press the Channel Up or Channel Down button to select

the memory location. If a memory location has been

programmed, its associated channel will display on the

LCD. Your radio is now in Marine Standby mode on the

selected memory location.

To Exit Memory Location Mode:

Press the Memory/Escape button to return the radio

to Marine Standby mode. The last channel used in

Marine Standby mode will now be displayed on the

LCD and the MEM icon will disappear.

To Erase Stored Memory Locations:

1. Press and hold the Memory/Escape button for two (2)

seconds. The memory location number will start flashing

and the MEM icon will be turned On.

2. Use the Channel Up and Channel Down buttons to

advance to the memory location you want to erase.

3. Press the Memory/Escape button to select the memory

location. The memory channel number will stop flashing

and the channel number will start flashing.

4. Use the Channel Up and Channel Down buttons to

change the channel to read “00” at the selected memory

location.

5. Press the Memory/Escape button to erase that memory

location.

Repeat steps 2 through 5 to erase as many additional

memory locations as you want.

6. Press and hold the Memory/Escape button for two (2)

seconds. This will return the radio to Memory mode.

7. Press and release the Memory/Escape button again

to return to Marine Standby mode.

MEM Icon

Memory Location Scan Mode

During Memory Location Scan mode, the radio will rapidly

scan through all programmed memory channels. Whenever

any activity is detected on a channel, the radio will stop the

scan for 10 seconds to allow you to listen briefly on that

channel. It will then continue to scan unless you switch out

of Memory Location Scan mode.

NOTE

If there are fewer than two (2) memory locations

programmed in the radio, the Memory Location

Scan option will not be available. At least two (2)

memory locations need to be programmed to

use the Scan button.

To Enter Memory Location Scan:

1. From Marine Standby mode, press the Memory/Escape

button.

2. Press the DUAL WATCH/SCAN button. The radio will

immediately begin to scan all pre-assigned memory

channels. The SCAN and MEM icons will show on the

LCD.

3. A signal on any channel will stop the scan for

10 seconds to allow you to listen to the traffic

on that location.

4. Press the Channel Up or Channel Down button

to resume scanning the Memory Location Scan

channels or to change the scan direction.

5. To EXIT Memory Location Scan mode, press the

DUAL WATCH/SCAN button again. The SCAN and MEM

icons will disappear from the LCD and the radio will

return to Marine Standby mode.

Memory Location Scan

MEM/ESC Button

Scan Button

www.busse-yachtshop.de | info@busse-yachtshop.de

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cobra MR HH125 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cobra MR HH125

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info