Bedienungsanleitung Cobra MR HH90 VP (Seite 17 von 23) (Englisch)

538299

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Channels

Your radio will receive and transmit VHF signals on

the Channel indicated on the LCD. You can change

the Channel at any time using the Channel Up and

Channel Down buttons.

To change channels:

Press the Channel Up or Channel Down button.

You are on Channel 88, pressing the

Channel Up

button will advance to Channel 1. If you are on

Channel 1, pressing the Channel Down button

will advance to Channel 88.

You can hold the

Channel Up or Channel Down

button for fast advance.

The beep sound will occur only at the first press

of the button and not during fast advance.

If the radio is in the

Key Lock mode, the channel will not

change and the three beep error signal will sound.

Transmit Power Output

Your radio can Transmit selectively at one half or two watts

of power. Cobra

suggests you maintain the low power

setting for short-range communications, to conserve

battery life and to avoid overpowering nearby stations

with your signal. Use the high power setting for long-range

communications or when you do not receive a response

to a signal sent at one half watt.

To toggle between the High and Low Power modes:

Press the High/Low Power – Lock button.

The LCD will show which mode is in effect.

Nothing comes close to a Cobra

English

Getting Started Getting Started

Volume

The On-Off Power/Volume knob also controls the speaker

Volume. The Volume adjustment applies only to what you

hear from the speaker and does not affect the Volume of

your outgoing messages, which is controlled by the

circuitry of your radio.

To increase the volume:

Turn the On-Off Power/Volume knob clockwise.

To decrease the volume:

Turn the On-Off Power/Volume knob counter-clockwise.

Power Saver

Your radio has a unique circuit designed to extend battery

life. If there are no transmissions within 10 seconds, the

radio will automatically switch to

Power Save mode and the

Save icon will flash in the LCD. This will not affect the radio’s

ability to receive incoming transmissions.

U.S.A./International/Canada Channel Maps

Three sets of VHF Channel Maps have been established

for marine use in the U.S.A, Canada and the rest of the

world (international). Most of the channels are the same

for all three maps, but there are definite differences

(see information on pages 14 – 21). Your radio has all

three maps built into it and will operate correctly in

whichever area you choose.

To set your radio for the area in which you will be using it:

From Standby mode, press and hold the Weather/UIC

button for three seconds. The U, I or C icon will blink on

the LCD.

Repeat step 1 to shift to the next channel map(s).

Operating Your Radio Operating Your Radio

Low Power Mode

High Power Mode

High/Low Power – Lock Button

Channel Up or Do

wn Buttons

Currently On Channel 88

Power Saver Icon

eather/UIC Button

On-Off P

ower/Volume Knob

Active Channel Map Icon

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cobra MR HH90 VP Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info