Bedienungsanleitung Cobra MX46SPE (Seite 14 von 18) (Englisch)

634273

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

- 14 -

CAUTION! The equipment is suitable for use only in a power supply with permissible modulus of

system impedance is 0.237Ω or less.

10.2 CONNECTION FOR AUTO DRIVE – SELF PROPELLED

Grip the Self-drive control handle, the lawnmower will move forward automatically with about 3.6km/h,

release the self-drive handle, the lawnmower will stop moving.

Fig.9

CAUTION: your mower is designed to cut normal residential grass of a height no more than 250mm.

Do not attempt to mow through unusually tall dry or wet grass (e.g., pasture) or piles of dry leaves.

10.3 FOR THE BEST RESULTS WHEN MOWING

Clear lawn of debris: Be sure that the lawn is clear of stones, sticks, wire or other objects, which could be

accidentally thrown out by the mower in any direction and cause serious injury to the operator and others as

well as damage to property and surrounding objects.

Avoid cutting wet grass: For effective mowing do not cut wet grass, because it tends to stick to the

underside of the deck preventing proper mowing of the grass clippings.

General Recommendations: Cut no more than 1/3 the length of the grass. The recommended cut for

mowing is 1/3 the length of the grass. Ground speed will need to be adjusted so the clippings can be

dispersed evenly into the lawn. For especially heavy cutting in thick grass it may be necessary to use one of

the slowest speeds in order to get a clean well mowed cut. When mowing long grass you may have to cut the

lawn in two passes, lowering the blade another 1/3 of the length for the second cut and perhaps cutting in a

different pattern than was used the first time. Overlapping the cut a little on each pass will also help to clean

up any stray clippings left on the lawn. The mower should always be operated at full throttle to get the best

cut and allow it to do the most effective job of mowing.

Clean underside of deck: Be certain to clean the underside of the cutting deck after each use to avoid a

build-up of grass, which would prevent proper mulching. Mowing leaves. The mowing of leaves can also be

beneficial to your lawn. When mowing leaves make sure they are dry and are not laying too thick on the lawn.

Do not wait for all the leaves to be off the trees before you mow.

WARNING: if the mower blade strikes a foreign object, then stop the engine. Disconnect the plug from the

wall socket, thoroughly inspect the mower for any damage and repair the damage before restarting and

operating the mower. Extensive vibration of the mower during operation is an indication of serious damage.

The unit should be promptly inspected and repaired.

11. BLADE

The blade is made of pressed steel. It will be necessary to reshape it frequently (with a grinding wheel).

Ensure that it is always balanced (an unbalanced blade will cause dangerous vibrations). To check for

balance, insert a round rod through the central hole and support the blade horizontally. A balance blade will

remain horizontal. If the blade is not balanced the heavy end will rotate downwards. Reshape the heavy end

until the blade is currently balanced. To remove the blade (2), unscrew the blade screw (3).

Check the conditions of the fan (1), and replace any parts, which are damaged.

When reassembling, make sure that the cutting edges face in the direction of the motor rotation. The blade

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cobra MX46SPE Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info