Bedienungsanleitung Coinco Global 2 (Seite 11 von 38) (Englisch)

535645

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Page 11

800 Series

SECTION 3: CONFIGURATION

Setting The Vend Price On

A Single-Price Changer

The vend price on a single-price changer may

be set in four ways:

• via Coinco Support Software

• via DEX/UCS

• via the first eight Option Switches

• via the digital display.

The vend price can be set in single increments

up to 255 times the lowest denomination coin

that is accepted by the changer and routed to a

coin tube.

EXAMPLE: If the lowest denomination coin is

one, the highest vend price setting would be 255

x 1 or 255.

VIA COINCO SUPPORT SOFTWARE

Consult Coinco Support Software manual for

price setting instructions.

VIA DEX/UCS

Consult Hand-held Computer manufacturer.

VIA OPTION SWITCHES

Note: The switches are ON in the upwards

position.

1. Set the vend price by adding the amount of

the appropriate switches and setting them to

the ON position (see Figure 11).

2. Set Option Switch B to the OFF position.

3. Set Option Switches A, C and D to the

desired configuration (see “Option Switch

Module” section of this manual).

4. After setting the vend price and the desired

options, press and release the Mode Button

to store the new setting. The LED and the

“Use Correct Change” light will then flash

once, indicating that the price was recorded.

Figure 11

Example: Switch 1, 3, 4, set to on and the

remaining set to off would result in a price of

(1+4+8) x Scaling Factor. If the scaling factor

were set to 5 and the decimal point set to 2, the

resulting price setting would be (1+4+8) x (.05) =

13 x .05 = 0.65 units. The current scaling factor

can be displayed using display mode, address

“A010” on the acceptor. The current decimal

point position can be displayed using diplay mode,

address “A011”.

NOTE: The vend price must be set to an

amount greater than zero for the changer to

accept coins in single-price mode.

VIA DIGITAL DISPLAY

1. Enter the Display Mode (see “Display

Mode” section of this manual).

2. Press B to scroll up to “C001” (Price 1).

3. Press C to enter. The current Price Setting is

displayed.

4. Use buttons B (increase) and D (decrease) to

change C001 to the appropriate price.

5. Press A to store price and return to the

Display Mode.

7. Press A to exit the diplay mode.

Note: The Display Mode will exit automatically

if there is no programming action for 30

seconds.

Switch 1 ...................................1 x Scaling Factor

Switch 2 ...................................2 x Scaling Factor

Switch 3 ...................................4 x Scaling Factor

Switch 4 ...................................8 x Scaling Factor

Switch 5 .................................16 x Scaling Factor

Switch 6 .................................32 x Scaling Factor

Switch 7 .................................64 x Scaling Factor

Switch 8 ............................... 128 x Scaling Factor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Coinco Global 2 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info