Bedienungsanleitung Coinco Global 2 (Seite 15 von 38) (Englisch)

535645

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Page 15

800 Series

Setting The Float Mode

Levels

The Float Mode Levels for both Float Level and

Float Pay-down can be set in two ways:

• via Coinco Support Software;

• via the Digital Display.

VIA COINCO SUPPORT SOFTWARE

Consult Coinco Support Software manual for

tube float level setting instructions.

VIA DIGITAL DISPLAY

The Digital Display/Inventory Buttons are

located on the acceptor gate. Address “A007”

allows you to clear all float levels and to set all

four float levels at one time. The individual tube

float levels are set using Address “A008”.

Setting All Four Float Levels At Once:

1. Load the four coin tubes to the float level

you want the coin changer to maintain.

2. Enter the Display Mode (see “Display

Mode” section of this manual).

3. Press B to scroll up to Address “A007”

4. Press C to enter Address “A007”. The

display will show the current float mode

settings for all tubes. The far left digit

represents tube A through the far right digit

representing tube D.

5. Press B (increase) or D (decrease) to “1” to

set standard float levels, “2” for float pay-

down, or “0” to disable float mode.

6. Press C to enter your selection. The far right

decimal point will illuminate indicated the

selection has been stored.

7. Press A to return to the Address selection.

8. Press A again to exit display mode. All four

tube float levels are now set.

The Digital Display’s second decimal point

from the right will be illuminated if any tube

float levels have been set.

SECTION 3: CONFIGURATION

Setting Float Levels Individually:

1. Load the individual coin tube to the float

level you want the coin changer to maintain.

2. Enter the Display Mode (see “Display

Mode” section of this manual).

3. Press B to scroll up to Address “A008” for

individual tube float setting.

4. Press C to enter the Address.

5. “A” will be displayed indicating tube “A”.

Use button B (increase) or button D (de-

crease) to reach the desired tube selection.

6. Press C to enter the Sub Address.

7. Use button B (increase) to reach the correct

setting (“0” to disable, “1” for standard float,

“2” for float pay-down).

8. Press C to store setting. The far right deci-

mal point will illuminate indicating the

selection has been stored.

9. Press C again to return to the Sub Address

Display.

10.Press A to return to the Address Display.

11.Press A again to exit the Display Mode. The

tube float level is now set for the individual

tube you have chosen.

The Digital Display’s second decimal from the

right will be illuminated if any tube float levels

have been set.

Activating Float Pay-Down

Pressing and releasing buttons A and B simulta-

neously activates Float Pay-down. Use Manual

Fill to replenish low tubes (see “Manual Fill

Mode” section of this manual).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Coinco Global 2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info