Bedienungsanleitung Coinco Global 2 (Seite 23 von 38) (Englisch)

535645

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Page 23

800 Series

SECTION 3: CONFIGURATION

Changing The Coin Tubes

and Coin Routing

REMOVING/REPLACING THE TUBES

To remove the coin tubes, remove the acceptor

and then remove the grey, smoked front cover

by pulling out on the left side of the cover at the

notch in the housing. The front cover will

swing forward, exposing the tubes. The tubes

can be removed one at a time by pulling up-

ward. Four slots have been placed in the front

of the changer along the pay-out assembly area

to assist in this procedure. Place a screw driver

into the slot and apply an inward pressure to

free the tube retainer tab whilst pulling upwards

on the tube. Replace the coin tubes by inserting

the dove tail guides into the tube holes and

pushing inward and downward.

ABOUT THE SHIMS

The coin tubes in your COINCO GLOBAL2

changer utilise six interchangeable shims to

accommodate variable thicknesses of coins.

These shims are color-coded and are fixed to

the bottom of the coin tubes. Shims are re-

moved and replaced by sliding in or out of the

bottom of the coin tube.

NOTE: Do not reuse shims. Installation and

removal can stress the plastic, causing the

shims to lose their ability to stay firmly in

place.

CHANGING THE COIN ROUTING

After changing the coin tubes, the coin routing

needs to be reconfigured via the Digital Display

using Address “A002”.

This address allows the user to change payout

configuration in the field. This feature only

provides a means for the acceptor to alter coin

routing when different physical payout tubes

have been placed in the changer body.

When address A002 is entered five payout

configurations are available. Selection is

achieved by scrolling up (button B) or down

(button D) to the desired configuration. When

the desired setting is reached, press enter (but-

ton C) to store the selection. The far right

decimal point will illuminate to indicate the

setting has been stored to memory. If the

location has the capability of being program-

mable (Display shows Alt1 for example) press-

ing enter (button C) again will enter program-

mable mode. This will be evident if a value

between “a” and “e” is displayed.

To program a coin to a tube, select the tube by

scrolling to the desired tube, (‘a’ is the first tube

on the left) and drop the coin type to be routed

to the tube. If a coin’s value differs from the

coins currently routed to the tube, all coins

previously routed to the tube with different

values will be rejected. If value “e” is chosen

for a new destination, the coin type dropped will

have its routing changed to the cashbox. Press-

ing enter (button C) again will return to the

second sub address menu, esc (button A) will

always return to the high level address selection

menu.

For correct operation the scaling factor should

be equal to the value of the least coin accepted

E.g. if the least value coin accepted is the GBP

10p after altering the payout configuration the

scaling factor in address A010 should be

changed to 10.

Float modes will be turned off and coin counts

will be cleared for any tube in which all coins

assigned to the tube were not previously as-

signed to the tube and have been assigned

during the current payout configuration session.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Coinco Global 2 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info