Bedienungsanleitung Cointra Thermex Blitz IBL (Seite 2 von 9) (Englisch)

635863

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

4. Description and principle of operation

EWH consists of the housing, removable flange, safety valve, protective cover and Control Panel.

4.1.

The housing consists of the outer shell, made of plastic, internal tank, thermal insulated with

environmentally friendly polyurethane foam, and two threaded pipes for cold water inlet (blue ring) and

hot water exhaust (red ring).

Internal tank is made of stainless austenitic stainless steel, which ensures high corrosion resistance

and, as a consequence, long operation life.

4.2.

At the removable flange the following is mounted: tubular heater (HEATER), pipe thermostat.

TEH is used to heat water and thermostat provides with possibility to adjust temperature up to +74°

C (± 5° C). Temperature adjustment is made using adjustment knob located on the water heater

control panel (Fig. 1).

The thermal switch is used to prevent overheating and cut off EWH power when water

temperature exceeds +95° C (± 5° c) (fig. 2). EWH housing can heat inthe course of operation.

Two warning lights (button) located on the control panel (fig. 1) of the water heater next to the

temperature adjustment knob indicate operating mode: "POWER" light is on when the save mode

(1.5 kW), and TURBO light - when the full heating mode (2.5 kW). Switching between the modes is

made by pressing TURBO button, when button pressed "TURBO" mode is on, when released – save

mode. EWH power on/off is carried out by POWER button.

4.3.

Safety valve is back-flow valve preventing ingress of water from the water heater to

water main in case of pressure drop in the latter and in case of pressure increase in the tank

when water is heating up, as well as safety valve, relieving excess pressure in tank when water

is heating up. During water heater operation water may leak out of the exhaust outlet pipe of the

safety valve to relieve excessive pressure, which is made for the purpose of water heater

safety. This outlet pipe shall remain open to the atmosphere and be installed constantly down.

and in a non-freezing environment. You shall ensure drainage of water from exhaust pipe safety

valve into the drain, with installation of the corresponding EWH drainage.

It is required regularly (at least once a month) to discharge a small amount of water through the

exhaust pipe of the safety valve into the drain to remove lime deposits and to test the operating

functionality of the valve. Handle is intended to open the valve. It is necessary to control when

operating water heater this handle to be in position closing water draining from the tank.

5. Specifying security measures

5.1.

Electrical safety and corrosion protection of EWH are guaranteed only if there is an effective

earthing in accordance with applicable electric installation rules and regulations.

5.2.

Plumbing pipes and fittings shall conform to parameters of water main and have the required

certificates of quality.

5.3.

When installing and operating EWH the following is not allowed

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cointra Thermex Blitz IBL Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info