Bedienungsanleitung Cointra Thermex ID (Seite 5 von 12) (Englisch)

635854

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

6.1. LAYOUT AND INSTALLATION

The EWH should be installed in accordance with the marking on the case and the table below:

Marking

Volume

Layout

RZL, IS-V, IR-V, IQ-V, IF-V,

ID-V

30- 150 litres

Vertical, with branch pipes

downwards

IS-H, IR-H, IQ-H, IF-H, ID-Н

30- 150 litres

Horizontal, with branch pipes

downwards

IS-U, IR-U, IQ-U, IF-U, ID-U

30 - 150 litres

Vertical or horizontal, with

branch pipes downwards or to

the right, respectively

Models IR 5-15 l are placed vertically.

To reduce heat loss in the pipes, it is recommended to install the EWH as close to the

place, where hot water is to be used, as possible.

The EWH is suspended by the case brackets on the anchor hooks fixed in a wall.

Mounting hooks in the wall should exclude spontaneous movement of the EWH brackets on

them.

For the servicing of the EWH, a distance from the protective cover to the nearest surface

in the direction of the axis of the removable flange must be at least:

- 30 centimeters - for models with a capacity of 5-80 litres;

- 50 centimeters – for models with a capacity of 100-150 litres.

WARNING! To avoid damage to the Consumer’s and (or) third parties’ property, when the

hot water supply system is out of order, install the EWH in the rooms provided with floor

waterproofing and drainage to a sewer system. Never place under the EWH things that are

exposed to water. When placing the EWH in unprotected areas, install under the EWH a

protective pallet provided with drainage to a sewer system.

When the EWH is installed in places that are not easily accessible for technical and warranty

maintenance (built-in shelves, recesses, inter-ceiling spaces, etc.), the EWH should be removed

and installed by the Consumer alone, or at his expense.

Note: the protective pallet is outside the scope of the EWH supply.

6.2. CONNECTION TO A WATER SUPPLY SYSTEM

Install the safety valve at the cold water inlet marked with a blue ring by giving it 3.5 - 4

turns and making the connection tight with any waterproof material (flax, FUM tape, etc.)

Do not use the EWH without a safety valve or the other manufacturers’ valves.

When the EWH is in operation, you can watch the appearance of drops from a drain beak

of the safety valve (relieving excessive pressure when water is heated). It is recommended to

connect to a drain beak a rubber or silicon tube of an appropriate diameter to remove moisture.

Connection to a water supply system is made in accordance with Fig. 1 (for models IS-U,

IR-U, IQ-U, IF-U, ID-U in the case of horizontal connection - Fig. 2, while the cold water supply

branch pipe must be below the hot water branch pipe intake) only through copper, metal-plastic

and plastic pipes, and through а special flexible plumbing inlet pipe. It is recommended to supply

water to the EWH through a mud filter mounted in a cold water line (which is outside the scope

of supply).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cointra Thermex ID Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cointra Thermex ID

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info