Bedienungsanleitung Cointra Thermex ID (Seite 9 von 12) (Englisch)

635854

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

When the EWH is turned on for the first time (or after power outages), a temperature is set on

default at +75°С.

7.3. Models with electronic control by version 2 (Fig.6)

7.3.1. "Demo" mode

In the models equipped with an electronic control panel by version 2 with a digital touch

LED display, when the EWH is turned on for the first time (or after power outages), the water

heater passes, on default, into "Demo" (demonstration) mode. In this mode, the EWH heating

elements are never enabled.

WARNING! Before interrupting "Demo", make sure that the EWH is filled with water.

Passage into and interruption of the "Demo" mode is done (if necessary) by pressing and holding

for 5 seconds keys and on the control panel.

7.3.2. Standby mode

Occurrence of the device in standby mode is accompanied by the flashing of logo

"Thermex," the temperature indicator indicates the temperature of water in the EWH, and the

clock shows the current time.

7.3.3. Heating mode

The EWH can be enabled (disabled) in the heating mode by pressing key . When the

heating mode is enabled, the EWH starts heating water to a preset temperature, and, on reaching

a preset temperature, the heating indicator will light steadily. In the heating mode, the heating

power can be selected by pressing keys and on the control panel. The 2 kW power

mode is accompanied by indication of pilot lamp "Double power," and 1.3 kW by indication of

pilot lamp "Single power."

7.3.4. Timer mode

The timer mode can be enabled (disabled) by pressing key on the control panel and is

accompanied by switching on (off) "Timer" indicator. After passage into the timer mode, the

EWH will be in standby mode until a preset time is reached. On reaching the preset time, the

EWH starts heating water to a preset temperature.

7.3.5. Adjustment of the EWH parameters

When the EWH is in operation, the Consumer can adjust the operating parameters in any

mode. Pressing any key on the control panel is accompanied by a sound signal. After the first

pressing of key (Setting or Selection) the value of "Single power" or "Double power" starts

flashing, and with keys and you may select an appropriate power mode. The second

pressing allows you to set a temperature up to which water will be heated in the EWH, with keys

or you may adjust the parameter up to an appropriate value. Prolonged holding of keys

or allows you to quickly change the parameter. The third pressing of key provides

for setting of the value of current time hours. The fourth pressing allows you to set current time

minutes. The fifth pressing can set an hour of timer in service, and the sixth pressing can set

minutes of timer in service. After the seventh pressing or within 5 seconds of the last pressing of

key the system will return to work. Discreteness of temperature changes -1°С. Temperature

is set on default at +75°C.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cointra Thermex ID Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cointra Thermex ID

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info