Bedienungsanleitung Cola Betty (Seite 6 von 11) (Englisch)

669019

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

5 Betty

1.7 Dataplate

The dataplate is located on the back of the stove. It gives the following data :

- model;

- serial number;

- type of fuel;

- nominal heat output;

- CO measured with 13% O2

- thermal efficiency;

1.8 Instructions for ordering replacement parts

For the end-user:

Contact your service centre and/or dealer to order replacement parts.

For the dealer:

To request any replacement parts contact the Cola s.r.l. after-sales service and/or send a fax clearly specifying

the following data:

- stove model;

- serial number;

- date of purchase;

- list of replacement parts;

- details of faults encountered.

- All work on parts must be carried out by authorised and/or qualified personnel.

- Only use original replacement parts

1.9 Stove decommissioning

For disposal, the stove must be sealed inside strong packing; contact the local authority in charge of such

operations in order to proceed according to the current local regulations.

2 – TRANSPORT AND INSTALLATION

2.1 Packing, handling, shipment and transport

The stove can be lifted using a lift truck, inserting the forks (of suitable length) in the special spaces in the wooden

packing.

Make sure the equipment used for lifting and transport can take the weight of the stove, specified on the dataplate

and in this manual.

Avoid taking the load in areas where it could be a danger if dropped.

Set the stove down on the floor carefully without bumping, and position it in the required place; make sure the

floor can take the weight of the stove, otherwise contact a specialised technician.

2.2 Instructions for safe installation

The stove must be installed by a technician, taking into account the local, national and European regulations. The

stove must be placed on a floor able to take its weight; otherwise corrective measures can be taken according to

the advice of specialised technicians.

Do not keep flammable or heat-sensitive parts near the glass. The minimum front distance for the protection of

flammable objects is 80 cm. Flammable or heat-sensitive parts must be at least 20 cm from the side and the

back wall. If the support base is made of flammable material (wood, cork, etc.) a protection base in 2-3 mm thick

steel plate or a sheet of toughened glass must be provided.

2.3 Connection to the flue

The stove must be connected to the flue with connection supports place on the top part of the stove body and by

means of flue pipes readily available on the market. Connection to the chimney must be made using strong and

stable pipes at least 1.2-2 mm thick. The flue pipe must possibly be straight, to avoid pressure losses, and

towards the flue. The single parts of the exhaust gas pipe must be tight.

To ensure regular operation, the flue draught with stove operating must be between 10 and 14 Pa.

For maximum stove efficiency, a draught control or

damper should be installed in the

flue pipe or chimney.

Every unit must eliminate the fumes through its own flue; never use the same flue for several units.

- hourly consumption;

- flue pipe size;

- minimum safety distance;

- stove external dimensions;

- weight.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cola Betty Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info